Haier HSU-30LNL03/R2(T3) Manual

Haier Ikke kategoriseret HSU-30LNL03/R2(T3)

Læs nedenfor 📖 manual på dansk for Haier HSU-30LNL03/R2(T3) (8 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 19 personer og blev bedømt med 4.9 stjerner i gennemsnit af 10 brugere

Side 1/8
Please read this operation manual before using the air conditioner.
Keep this operation manual for future reference.
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
0010539051
Contents
1
2-4
5
7
6.7
CAUTIONS
PARTS AND FUNCTIONS
OPERATION
MAINTENANCE
TROUBLE SHOOTING
HSU-18LEG03(T3)
HSU-18HEG03(T3)
HSU-24LEG03(T3)
HSU-24HEG03(T3)
HSU-18LEG13(T3)
HSU-18HEG13(T3)
HSU-24LEG13(T3)
HSU-24HEG13(T3)
HSU-30LEG13(T3)
HSU-30HEG13(T3)
HST-30LEG13(T3)
HST-30HEG13(T3)
HST-18LEG13(T3)
HST-18HEG13(T3)
HST-24LEG13(T3)
HST-24HEG13(T3)
HSU-12HEG13(T3)
HSU-09HEG03
HSU-12HEG03
HSU-24HEG03
HST-18LEG03(T3)
HST-24LEG03(T3)
1
Parts and Functions
Remote controller
Indoor Unit
Outdoor Unit
4
Loading of the battery
1
2
3
4
OUTLET
INLET
CONNECTING PIPING
AND ELECTRICAL WIRING
DRAIN HOSE
Remove the battery cover;
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
is in line with the" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change- over
wireless telephone is installed in the
ver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
type fluorescent lamp or
room, the recei
Note:
Full display or unclear display during operation indicates the
ries have been used up.Please change batteries.
If the remote controller can't run normally during operation, please
reload several minutes later.
batte
remove the batteries and
4
Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.
Display board
(adjust left and
ow)
Vertical blade
r ight air fl
Air Purifying FilterInlet (inside)
Emergency
Switch
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Outlet
Inlet grille
Display board 1 42 3 5
Signal receiver hole
ON/OFF display
4
2
3
1
5
TIMER ON\OFF display
SLEEP display
Ambient temp.display
When receiving the remote
control signal, display the set
displayed.
time the room temperature is
temperature and in the rest
Note to the power failure resume:
press the sleep button ten times in five seconds
and enter function after hearing four sounds.And
press the sleep button ten times within five
seconds and leave this function after hearing
TIMER ON-OFF display
COOL\HEAT\Dry\AUTO display
two sounds.
1. Mode display
2. Signal sending display
4. FAN SPEED display
5. LOCK display
6. TIMER OFF display
TIMER ON display
LO MED HI
7.TEMP display
16. LOCK button
Used to lock buttons and LCD display.
25. RESET button
When the remote controller
appears abnormal, use a sharp
pointed article to press this button
to reset the remote
22. HOUR button
Operation mode AUTO FANCOOL DRY
Remote controller
HEAT
1
2
3
4
5
9
10
11
12
13
14
15
16
17
22
23
24
25
19
20
21
8
18
7
6
Control the lightening and extinguishing
of the indoor LED display board.
3. SWING display
8.
9. TURBO button
10. FAN button
11. COOL button
12. AUTO button
13. FAN SPEED button
14. TIMER button
15. SLEEP button
17. LIGHT button
18. POWER ON/OFF button
19. DRY button
20. TEMP button
21. SWING button
23. EXTRA FUNCTION button
24.CANCEL/CONFIRM button
AUTO
Function: Setting and cancel to the
timer and other additional functions.
Display
circulated
Operation mode
Remote controller
QUIET TURBOSLEEP
supplemental
electrical
heating HEALTH
Additional functions display
NOTE: Healthy function is not available for some units.
Function: Health--- Healthy airflow
position1--- Healthy airflow position 2
--- Restore the original flap position---
Right & left air airflow--- A-B yard---
Refresh air(reserved function)--- QUIET
--- Fahrenheit/Celsius mode conversion
Remote controller A
1. Mode display
2. Signal sending display
4. FAN SPEED display
5. LOCK display
6. TIMER OFF display
TIMER ON display
LO MED HI
7.TEMP display
16. LOCK button
Used to lock buttons and LCD display.
25. RESET button
When the remote controller
appears abnormal, use a sharp
pointed article to press this button
to reset the remote
22. HOUR button
Operation mode AUTO FANCOOL DRY
Remote controller
HEAT
1
2
3
4
5
9
10
11
12
13
14
15
16
17
22
23
24
25
19
20
21
8
18
7
6
Control the lightening and extinguishing
of the indoor LED display board.
3. SWING display
8.
9. TURBO button
10. HEAT button
11. COOL button
12. AUTO button
13. FAN SPEED button
14. TIMER button
15. SLEEP button
17. LIGHT button
18. POWER ON/OFF button
19. DRY button
20. TEMP button
21. SWING button
23. EXTRA FUNCTION button
24.CANCEL/CONFIRM button
AUTO
Function: Setting and cancel to the
timer and other additional functions.
Display
circulated
Operation mode
Remote controller
QUIET TURBOSLEEP
Supplemented
electrical
heating HEALTH
Additional functions display
Function: Health--- FAN---
Healthy airflow
position1---
--- Healthy airflow position 2---
Right & left air airflow--- A-B yard---
function
)-- QUIET--- Refresh air( reserved
--- Fahrenheit/Celsius mode conversion
HEAT
Low-Temperature Heating Operation Down to 10
Remote controller B
FAN
Actual inlet grille may vary from the one shown in the
manual according to the product purchased


Produkt Specifikationer

Mærke: Haier
Kategori: Ikke kategoriseret
Model: HSU-30LNL03/R2(T3)

Har du brug for hjælp?

Hvis du har brug for hjælp til Haier HSU-30LNL03/R2(T3) stil et spørgsmål nedenfor, og andre brugere vil svare dig