Haier HWM-60-12699 Manual

Haier Vaskemaskine HWM-60-12699

Læs gratis den danske manual til Haier HWM-60-12699 (8 sider) i kategorien Vaskemaskine. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Haier HWM-60-12699, eller vil du spørge andre brugere om produktet?

Side 1/8
HWM70-12688NZP
HWM60-12699NZP
HWM70-12688NZP
HWM60-12699NZP
1/12 2/18 3/24 4/29
5/33 6/37 7/41 8/46
L 500mm W 520mm H 902mm
No or slow drain the digitron
displays“E1”,buzzing.
No or slow water filling the digitron
displays“E4”,buzzing.
The digitron displays“FA”,buzzing.
The machine does
not act.
Not wash
Not spin
Water level sensor is abnormal? Please contact with after-sales service
department.
The water tap is not open.
The water inlet valve is blocked.
The water pressure is too low
and the current is too small.
Are the laundries put slantingly?
Is the machine slanting?
Open the tap.Open and close the top lid once,
then press the START/PAUSE button.
Clean the water inlet walve,Open and close the
top once.then press the START/PAUSE button.
Wait for the normal water pressure before use.
Re-order the laundries.Close the top lid and
press the button.START/PAUSE
Safety switch actuates,not spin,
(after self-correction twice),the digitron
displays“E3”,buzzing.
Is the drain hose put down?
Is the drain hose blocked by
foreign material?
Put down the drain hose.Open and close the top
lid once then press the START/PAUSE button
Clean the foreign material.Open and close the
top lid once,then press the START/PAUSE button
Level the machine in right position
Note: when the digital tube displays the abnormal symbol during working,it buzzs once in
succession every two minutes,then the power will be cut automatically after ten minutes.
When the power plug is inserted, computer
board indicator is switched on, and the
machine starts working.
It is the special resume function. In the case of power
failure or the power plug is loose during washing, the
machine can save the running program, and resume
the program after the power supply is recovered. You
do not need to set the program again.
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset
position?
Is the top lid closed?
Use it when there’s power supply.
Insert the power plug tightly.
Fill water to the preset position
Close the top lid
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
There’s abnormal sound
inside the machine
Is the machine slanting?
Are the laundries put slantingly in
spinning?
Adjust the machine to be even.
Reorder the laundries and close the
top lid.
The water tap leaks Fasten the jointer properly.
Is the jointer of water inlet hose
loose or twisted awry?
114
Phenomena The reason How to settle
The digitron displays E2. The top lid is not closed. Close the top lid or close the top lid
and press the START/PAUSE button
Please first pull off the power plug from the receptacle before cleaning.
After using, please clean the lint and foreign materials of the lint filter and
overflow filter in time. Otherwise it may influence your using the machine.
After washing
The lint filter must be used during washing.
It must be cleaned in time after each using.
The methods of dismantle and install lint filter as follows:
1.Push down the spring piece of the top lint filter to
make the claws out of the filter cover,and then pull out
the lint filter to get it down.(figure 1)
2.Pull the back cover of the lint filter, and then you can
get down it off the front cover (figure 2)of the lint the lint
filter.
3.Sweep the rubbish in the lint filter.
4.Put the back cover of the lint filter into the front cover.
(figure 2)
5.Put the lint filter into filter cover, and make it tight.
6.Make sure the lint filter well installed,or it can influence
your use.
The filter screen of the water inlet valve is likely
to be blocked by foreign materials and influence
the water inlet.
Please clean it with brush every two months.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose.)
2.Do not store water in the washing machine for a long period. Drain the water completely
after each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid
for some time (about 1 hour), then close the top lid.
(If there’s breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair.
If there are real breakdowns, please come to the special maintenance department or after-sale
service department of our company. Do not repair it by yourself.


Produkt Specifikationer

Mærke: Haier
Kategori: Vaskemaskine
Model: HWM-60-12699

Har du brug for hjælp?

Hvis du har brug for hjælp til Haier HWM-60-12699 stil et spørgsmål nedenfor, og andre brugere vil svare dig