Hamlet HBCS2D100W Manual

Hamlet Stregkodelæser HBCS2D100W

Læs gratis den danske manual til Hamlet HBCS2D100W (8 sider) i kategorien Stregkodelæser. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Hamlet HBCS2D100W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

MANUAL SUCCESSIVE SCAN

AUTO-CONDUCTION TRIGGER COMMAND

ENTER* ENTER AND LINE

TAB NONE

NORMAL

ILLUMINATION*

CONTINUOUS

LIGHT MODE

SCAN MODE

SUFFIX SETTINGS

ILLUMINATION AND AIM

SLEEP TIME SETTINGS

ENTER SLEEP

TIME SETTING

SAVE SLEEP

TIME PARAMETER

1. Scan “Enter Sleep Time Setting” QR code.

2. Set sleep time parameter (Unit: minutes).

Example: To set sleep time 10 minutes, scan sleep

time number “0”, “1” and “0” in sequence.

Note: Sleep time can be from 1 to 999 minutes,

consinsting of 3 digits, followed by one hundred, ten,

a bit. Each set of sleep time must be 3 digits number.

3. Scan “Save Sleep Time Parameter”.

Note: After setting the sleep time parameter, it must

be saved. If set error, the scanner will give an alarm

and you need to set it again.

Under data uploading mode, the purple led indicator

keeps flashing when uploading data.

Under invetory mode, the red led indicator keeps on

when uploading data.

Under over-distance storage mode, the red led

indicator keeps flashing when uploading data.

When battery power is too low, the scanner makes

“beep” every 10 seconds. After 5 “beep” sounds, the

scanner turns off automatically.

When the scanner is in over transmission distance

condition, connect the scanner to the receiver and

press trigger button to upload data to the receiver. But

data will not be uploaded to a cell phone.

When the scanner is in inventory mode, it will not go

into over-distance storage mode.

Note: To return to Factory Default settings, scan

“Factory Default”, “RF Setting” and “Bluetooth Mode”

QR codes in sequence.

1. Connect the USB receiver to the computer.

2. Scan below QR code or “Disconnect” QR code on

the receiver.

3. Scan “Connect” QR code on the receiver and wait

few seconds to complete pairing.

Note: Purple led indicates pairing succeed.

INTRODUCTION

One Scanner To One Receiver

Open Android or iOs devices

bluetooth and search for bluetooth

devices after scanning this barcode,

then connect to the bluetooth

device.

Connect To Mobile Device

In iOS, if keyboard is on, scan this

code to turn off the keyboard.

If keyboard is off, scan this code to

turn on the keyboard.

Keyboard ON/OFF in iOS

UPLOAD ALL DATA

CLEAR ALL

DATA

UPLOAD

STATISTIC DATA

QUIT

INVENTORY MODE

ENTER

INVETORY MODE

INVENTORY MODE

HBCS2D100W

www.hamletcom.com

BLUETOOTH INDUSTRIAL BARCODE

SCANNER FOR LINEAR AND QR CODES

USER MANUAL

2D BARCODE SCANNER

Dear Customer,

thanks for choosing an Hamlet product. Please

carefully follow the instructions for its use and

maintenance and, once this item has run its life

span, we kindly ask You to dispose of it in an environmen-

tally friendly way, by putting it in the separate bins for

electrical/electronic waste, or to bring it back to your

retailer who will collect it for free.

We inform You this product is manufactured with

materials and components in compliance with RoHS

Directive 2011/65/EU, WEEE Directive 2002/96/CE,

2003/108/CE Italian Legislative Decree 2005/151 and

RED Directive 2014/53/EU for the following standards:

EN 60950-1: 2006 + A2: 2013

EN 62479: 2010

EN 301 489-1 V1.9.2

EN 301 489-17 V2.2.1

EN 300 328 V1.8.1

CE Mark Warning

This is a Class B product. In a domestic environment, this

product may cause radio interference, in which case the

user may be required to take adequate measures.

The complete CE declaration of conformity of the product

can be obtained by contacting Hamlet at

info@hamletcom.com.

Visit www.hamletcom.com for complete information on

Hamlet products and to access downloads and technical

support.

Imported by:

CARECA ITALIA SPA - Scandiano (RE) . Italy

All trademarks and company names mentioned in this

manual are used for description purpose only and remain

property of their respective owners. The material in this

document is for information only. Contents, specifications

and appearance of the product are indicative and may

change without notice.

LED Devices

Hamlet products using led sources comply with IEC

60825-1, EN 60825-1: 2014. The led classification is

marked on one of the labels on the product. Class 1 Led

devices are not considered to be hazardous when used

for their intended purpose.

The following statement is required to comply with US

and international regulations:

Caution: Use of controls, adjustments or performance of

procedures other than those specified herein may result

in hazardous led light exposure.

Class 2 Led scanners use a low power, visible light diode.

As with any very bright light source, such as the sun, the

user should avoid staring directly into the light beam.

Momentary exposure to a Class 2 Led is not known to be

harmful.

In accordance with Clause 5, IEC 60825 and EN 60825,

the following information is provided to the user:

CLASS 1: CLASS 1 LED PRODUCT

CLASS 2: VISIBLE LED RADIATION

DO NOT STARE INTO BEAM

CLASS 2 LED PRODUCT

RF SETTINGFACTORY

DEFAULT

OVER-DISTANCE

STORAGE OFF

OVER-DISTANCE

STORAGE ON

BLUETOOTH

MODE

NO ILLUMINATION

Produkt Specifikationer

Mærke:	Hamlet
Kategori:	Stregkodelæser
Model:	HBCS2D100W
Type:	Håndholdt stregkodelæser
Bredde:	62 mm
Dybde:	85 mm
Højde:	154 mm
Vægt:	190 g
Produktfarve:	Sort
Batterikapacitet:	2200 mAh
Batteriteknologi:	Lithium
Scanner type:	1D/2D
Kabler inkluderet:	USB
Forbindelsesteknologi:	Trådløs
Strømkilde type:	Batteri
Trådløs rækkevidde:	100 m
Sensortype:	CMOS
Standard grænseflader:	RF trådløst
Ekstern strømadapter:	Ja
Lydalarm:	Ja
Læsehastighed (maks.):	300 læs/sek.
Understøtter lineær (1D) stregkoder:	EAN 128, EAN-13, EAN-8, Interleaved 2 of 5, U.P.C.
Understøtter matrix (2D) stregkoder:	QR Code