Hikvision DS-KAD706Y Manual

Hikvision Ikke kategoriseret DS-KAD706Y

Læs gratis den danske manual til Hikvision DS-KAD706Y (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 66 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 33.5 anmeldelser. Har du et spørgsmål om Hikvision DS-KAD706Y, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

DS-KAD706Y(-P)

Two-Wire Video & Audio Distributor

1 2 3

4 5

2 3 4 5

7 8

UD29992B

Network

MAX

24VDC

Network

Door Station

Video/Audio Distributor

Indoor Station

24AWG(0.2 mm², 9

Ω/100 m)

20AWG(0.5 mm², 3.5

Ω/100 m)

18AWG(0.8 mm², 2.5

Ω/100 m)

All

DS-KAD706Y - DS-KAD706Y-S Transmission

Distance ≤ 60 m

Transmission

Distance ≤ 60 m

Transmission

Distance ≤ 60 m

DS-KAD706Y - DS-KAD706Y Transmission

Distance ≤ 60 m

Transmission

Distance ≤ 60 m

Transmission

Distance ≤ 60 m

DS-KAD706Y-DS- KD8003Y-IME2 Transmission

Distance ≤ 35 m

Transmission

Distance ≤ 35 m

Transmission

Distance ≤ 35 m

Transmission

Distance ≤ 35 m

Transmission

Distance ≤ 35 m

Transmission

Distance ≤ 60 m

Transmission

Distance ≤ 60 m

DS-KAD706Y-DS-KH6320Y-WTE2 Transmission

Distance ≤ 35 m

Transmission

Distance ≤ 60 m

Transmission

Distance ≤ 60 m

Twisted Pair Parallel lines

Routing Path

MAX

24VDC

MAX

24VDC

24 VDC

Power Input

Diagram References

Appearance

Power Indicator

Cascade Interface

Network Indicator

Network Interface Cascade Network Indicator

Reset ButtonPower Input

Terminals

Wiring

Wire the devices with power supply cables as picture shown.

Door station should be connected to CH6 of the video/audio distributor with two-wire cables.

Indoor Station should be connected to any terminal of CH1 to CH5 of the video/audio distributor

with two-wire cables.

Caution: Make sure all the related equipment is power-off during the installation.

●The power output of CH1 to CH5: 24 VDC, Max. 6W.

●The power output of CH6: 24VDC, Max. 16 W.

Installation

Before you begin:

● Make sure the device in the package is in good condition.

● Make sure all the related equipment is power-off during the installation.

● Check the product specification for the installation environment.

Wall Mounting

1. Fix the DIN rail onto the wall.

Note: You are required to utilize a matched DIN rail.

2. Press the red clip upward, and lock it to the DIN rail.

Tips for Cables and Installation

Cables and Wiring

● When there are multiple cores in one parallel line, only one pair of closed cores are allowed

to transmit signal. It is not allowed to use multiple pair of cores in one cable to transmit

signal.

● When using parallel lines, it is suggested to use those with shielding layer. If dual core or

multiple core parallel lines without shielding layer are routed, stability of signal

transmission can be effected. You need to run a test before installation.

● Impedance of cable should not be over suggested value, or distributor cannot transmit

enough power to indoor station or door station.

● Strong electricity and weak electricity cannot be wired in the same route, they need to be

wired separately and the distance should be more than 0.5 meter.

● All the cables used need to follow the restriction in the following table.

Device Installation

● Installation environment (temperature, moisture etc.) needs to follow requirements in

specification or power output can be effected.

● Power consumption of modular door station (main module and sub modules) should be less

than 12W. Please reach local technical support if you are not sure about power consumption

of each module. Door station should be connected to CH6 of the video/audio distributor. If

modular door station is connected to any terminal of CH1 to CH5, up to 3 sub modules can

be connected.

● Indoor station should be connected to any terminal of CH1 to CH5 of the video/audio

distributor.

● Up to 15 video/audio distributor can be cascaded. If more distributors are needed, you

should cascade network switch supporting 1000Mbps. The whole 2-wire system can have up

to 500 devices.

● Power supply must be certified by Hikvision.

● Indoor station needs to use firmware released after October, 2019.

Note: The power source should be qualified and meet limited power

source or PS2 requirements according to IEC 60950-1 or IEC 62368-1 standard.

Note:

The indoor station and doorstation are not contained in the package.

The adapter is contained in the DS-KAD706Y-P package.

Model Manufacturer

KPL-060M-II Channel Well Technology Co., Ltd

The detail for the power adapter contained

in the package is as follows:

Produkt Specifikationer

Mærke:	Hikvision
Kategori:	Ikke kategoriseret
Model:	DS-KAD706Y

Har du brug for hjælp?

Hvis du har brug for hjælp til Hikvision DS-KAD706Y stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Hikvision Manualer

Hikvision DS-A81024S Manual

28 Juli 2025

Hikvision ISD-SC5030S-2CVL Manual

28 Juli 2025

Hikvision DS-1471ZJ-155 Manual

28 Juli 2025

Hikvision DS-MDT301 Manual

27 Juli 2025

Hikvision ISD-SC5030SA-2CL Manual

27 Juli 2025

Hikvision DVR-208G-K1 Manual

27 Juli 2025

Hikvision DVR-204G-M1 Manual

27 Juli 2025

Hikvision DS-PI-D100 Manual

27 Juli 2025

Hikvision DS-MDT201 Manual

27 Juli 2025

Hikvision DS-TVG100-DH Manual

27 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Advantech PCE-3B03 Manual

30 Juli 2025

Graphite 57G100 Manual

30 Juli 2025

JUNG RCDME2044 Manual

30 Juli 2025

Neutrik NAC3FXXB-W-L Manual

30 Juli 2025

CYP OUTX-2100-AVLC Manual

30 Juli 2025

Advantech SOM-C350 Manual

30 Juli 2025

Deye SUN-33K-G04P3-EU-AM4-LV Manual

30 Juli 2025

Ghibli & Wirbel TOOL PRO WDA 40 H AS Manual

30 Juli 2025

Advantech UNO-3483G Manual

30 Juli 2025

Advantech ADAM-3956 Manual

30 Juli 2025