Hotpoint CS1A 400 H FM FA UK 1 Manual

Hotpoint Fryser CS1A 400 H FM FA UK 1

Læs gratis den danske manual til Hotpoint CS1A 400 H FM FA UK 1 (4 sider) i kategorien Fryser. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Hotpoint CS1A 400 H FM FA UK 1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

INSTRUCTIONS FOR USE

DIAGRAM OF THE APPLIANCE (Fig. 1)

A. Handle.

B. Safety lock (if provided).

C. Gasket.

D. Separator (if provided).

E. Defrost water drain plug.

F. Control panel.

G. Side motor cooling grille.

INSTALLATION

• Unpack the appliance.

• Remove the 4 spacers inserted between the door

and the appliance. (Fig. 3)

• Make sure the defrost water drain plug (if provided) is

correctly positioned (E).

• For optimum appliance operation and to avoid damage

when the door is opened, leave a space of at least 7 cm

from the rear wall and 7 cm at the sides. (Fig. 4)

• Fit the accessories (if provided).

• Clean the inside of the appliance before using it.

DIAGRAM OF THE CONTROL PANEL (Fig. 2)

a. Red LED: when ashing, it indicates that an alarm

condition is present see TROUBLESHOOTING GUIDE.

b. Green LEDs: they indicate that the appliance is in

operation, and the temperature has been set as follows:

b1 less cold temperature (right light on), use this setting

with partial loads will optimise energy consumption.

b2 middle temperature (centre light on)

b3 very cold temperature (left light on)

ALL Green LEDs ON: FAST FREEZING function is active;

see the section “freezing fresh food”.

c. Temperature setting button: to adjust the set

temperature and to activate/deactivate the fast freezing

operations.

To select the desired temperature, repeatedly press the

setting button (3): each time the button is pressed, the set

temperature is updated.

To activate/deactivate fast freezing function, pressing

for approximately 3 seconds: all green LEDs ash

simultaneously 3 times and then remain lit.

Note:

The settings will be saved in the memory even if

a power cut occurs. The time needed for the temperature

inside the freezer to reach the set value, can vary

depending on climatic conditions and the set temperature

itself.

SWITCHING ON THE APPLIANCE

• Plug in the appliance.

• The green LED lights up (middle temperature).

• The red LED ashes to indicate that the temperature

inside the appliance is not yet suciently low for food

storage. The red LED will normally switch o within the

rst six hours after the appliance is switched on.

• Place food inside the product only when the red LED has

switched o.

Note:

As the seal is tight, the appliance lid cannot be

reopened immediately after closing. Wait a few minutes

before re-opening the lid of the appliance.

This appliance features “skin condenser” technology:

the condensing unit is integrated into the walls of

the freezer. For this reason the side and front walls

of the product may become hot while the product

is running. This is entirely normal and also reduces

the risk of condensation forming in particularly

critical environmental conditions (see paragraph

“Troubleshooting guide”).

FREEZING FOOD

Preparation of fresh food for freezing

• Before freezing, wrap and seal fresh food in: aluminium

foil, cling lm, air and water-tight plastic bags,

polyethylene containers with lids, provided they are

suitable for freezing foods.

• Food must be fresh, mature and of prime quality in order

to obtain high quality frozen food.

• Fresh vegetables and fruit should preferably be frozen

as soon as they are picked to maintain the full original

nutritional value, consistency, colour and avour.

• Always leave hot food to cool before placing in the

appliance.

Freezing fresh food

• Place foods to be frozen in direct contact with the walls

of appliance:

A) - foods to be frozen,

B) - foods already frozen.

• Avoid placing foods to be frozen in direct contact with

food already frozen.

• For best and fastest freezing, foods should be split into

small portions; this will also be useful when the frozen

items are to be used.

1. At least 24 hours before storing fresh foods inside the

product for freezing, activate the fast freezing function by

pressing button for approximately 3 seconds. All green c

LEDs ( ) comes on.b

2. Introduce the food to freeze inside the appliance, and

keep the door of the appliance closed for 24 hours.

After this period the food will be frozen. The fast freezing

function can be deactivated pressing button for c

approximately 3 seconds.

If the fast freeze function is not manually deactivated, it

will be automatically deactivated by the appliance after

50 hours.

FOOD STORAGE

Refer to the table on the appliance.

Classication of frozen foods

Load and classify the frozen foods; it is advisable to indicate

the storage date on the packs, to ensure consumption

before the expiry dates listed in months in g. 6 for each

type of food.

Advice for storing frozen food

When buying frozen food, make sure that:

• The packaging is intact (food in damaged containers

may have deteriorated). If a package is swollen or has

damp patches, the product may not have been stored

in optimum conditions and therefore undergone partial

defrosting.

• When shopping, leave frozen food purchases until last

and carry them in a thermally insulated bag.

• On arriving home, immediately place the frozen food in

the appliance.

• Avoid or minimise temperature variations. Observe the

expiry date on the packaging.

• Always follow the storage instructions on frozen food

packages.

Note:

• Eat fully or partially defrosted foods immediately. Do

not refreeze unless the food is cooked after it has

thawed. Once cooked, the food can be refrozen.

• In case of a prolonged power failure:

Do not open the appliance door, except to place

ice packs (if provided) over the frozen foods on the

right and left side of the appliance. This will slow

down the rise in temperature.

APPLIANCE DEFROSTING

The appliance should be defrosted when the thickness of

ice on the walls reaches 5-6 mm.

• Disconnect the appliance from the power supply.

• Remove food from the appliance and put it in a very cool

place or a thermally insulated bag.

• Leave the appliance door open.

• Remove the internal defrost water drain plug (depending

on model) (Fig. 8).

• Remove the external defrost water drain plug (depending

on model) and reposition it as shown in gure 8.

• Use the separator (depending on model) inside the

product as a recipient for any remaining water, (D) as

shown in g. 8. If there is no separator, use a shallow

container.

• Defrosting can be sped up by using a spatula to detach

the frost from the appliance walls.

• Remove the frost from the bottom of the appliance.

• In order to avoid permanent damage to the

appliance interior, do not use pointed or sharp

metal instruments to remove the ice.

• Do not use abrasive products or heat up the interior

articially.

• Dry the inside of the appliance thoroughly.

• Ret the plug after defrosting.

CHANGING THE LID LIGHT BULB (if provided)

• Disconnect the appliance from the mains power supply.

• Remove the diuser by following the sequence of steps

shown in the gure.

• Unscrew the light bulb and replace it with an identical

bulb of the same wattage and voltage.

• Ret the diuser and plug in the appliance.

TROUBLESHOOTING GUIDE

1. The red LED ashes.

• Is there a power failure?

• Is a defrosting operation in progress?

• Has fresh food recently been introduced?

• Is the appliance lid properly closed?

• Is the appliance placed near a heat source?

• Are the ventilation grille and condenser clean?

2. All LEDs ash at the same time.

• Contact the After-Sales Service.

3. The appliance is too noisy.

• Is the appliance perfectly horizontal?

• Is the appliance in contact with other furniture or

objects that may cause vibrations?

• Has the packaging been removed from under the

appliance?

Note:

Gurgling noises from the refrigerating circuit after the

compressor cuts out are perfectly normal.

4. All LEDs are o and the product is not working.

• Is there a power failure?

• Is the plug properly inserted in the socket?

• Is the electric cable intact?

5. All LEDs are o and the product is working.

• Contact the After-Sales Service.

6. The compressor runs continuously.

• Have hot foods been put in the appliance?

• Has the appliance lid been left open for a long time?

• Is the appliance placed in a very warm room or near

heat sources?

• Has the fast freeze function been activated? (All green

LEDs ON)

7. Too much ice on the upper edge.

• Are the defrost water drainage plugs correctly

positioned?

• Is the appliance lid properly closed?

• Is the appliance lid seal damaged or deformed? (See

chapter “Installation”)

• Have the 4 protection pieces been removed? (See

chapter “Installation”)

8. Formation of condensate on the external walls of

the appliance.

• It is normal for condensation to form under certain

atmospheric conditions (humidity above 85%) or if the

appliance is located in a damp or poorly ventilated

room. The performance of the appliance is in no way

aected.

9. The layer of ice on the internal walls of the

appliance is not uniform.

• This phenomenon is quite normal.

ELECTRICAL CONNECTION FOR GREAT BRITAIN

AND IRELAND ONLY

Warning – this appliance must be earthed.

Fuse replacement

If the mains lead of this appliance is tted with a BS 1363A

13amp fused plug, to change a fuse in this type of plug use

an A.S.T.A. approved fuse to BS 1362 type and proceed

as follows:

1. Remove the fuse cover (A) and fuse (B).

2. Fit replacement 13A fuse into fuse cover.

3. Ret both into plug.

Important:

The fuse cover must be retted when changing a fuse and

if the fuse cover is lost the plug must not be used until a

correct replacement is tted.

Correct replacement are identied by the colour insert or

the colour embossed in words on the base of the plug.

Replacement fuse covers are available from your local

electrical store.

For the Republic of Ireland only

The information given in respect of Great Britain will

frequently apply, but a third type of plug and socket is also

used, the 2-pin, side earth type.

Socket outlet / plug (valid for both countries)

If the tted plug is not suitable for your socket outlet, please

Produkt Specifikationer

Mærke:	Hotpoint
Kategori:	Fryser
Model:	CS1A 400 H FM FA UK 1

Har du brug for hjælp?

Hvis du har brug for hjælp til Hotpoint CS1A 400 H FM FA UK 1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fryser Hotpoint Manualer

Hotpoint BF 1801 E F2 Manual

1 August 2025

Hotpoint UH8 F1C W 1 Manual

1 August 2025

Hotpoint HTSD18F013H1 Manual

16 Juli 2025

Hotpoint CS1A 250 H FA Manual

10 Juni 2025

Hotpoint HBNF55182SAQUAUK Manual

30 Januar 2025

Hotpoint HF 1801 E F2 Manual

30 Januar 2025

Hotpoint H55ZM 1120 W Manual

30 Januar 2025

Hotpoint H55ZM 1120 B Manual

30 Januar 2025

Hotpoint UH8 F2C W Manual

12 December 2024

Hotpoint HABUFZ011 Manual

12 December 2024

Fryser Manualer

Nyeste Fryser Manualer

Continental Edison CECUF204NFS Manual

14 September 2025

Liebherr FNe 1404 Manual

14 September 2025

Exquisit GB40-050CW Manual

14 September 2025

Exquisit GB40-050CB Manual

13 September 2025

Liebherr FNc 467i Manual

13 September 2025

Liebherr FNsddi 1624 Plus Manual

13 September 2025

Liebherr BFPSvh 6501 Manual

13 September 2025

Liebherr FNd 505i Prime Manual

13 September 2025

Liebherr SFFvh 4001 Manual

13 September 2025

Liebherr EFL 3005 Manual

13 September 2025