Hotpoint H0I D534A S Manual

Hotpoint Opvaskemaskine H0I D534A S

Læs gratis den danske manual til Hotpoint H0I D534A S (8 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Hotpoint H0I D534A S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

ENQuick Guide

THANK YOU FOR BUYING A HOTPOINT ARISTON PRODUCT.

In order to receive a more complete assistance, please register

your appliance on: www.hotpoint.eu/register

Before using the appliance carefully read Safety Instructions

guide.

PLEASE SCAN THE QR CODE ON YOUR

APPLIANCE IN ORDER TO HAVE MORE

DETAILED INFORMATION

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and on

the machine’s functional components.

• It is mandatory that the salt reservoir never be empty.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher and must be

lled when the SALT REFILL indicator light in the control panel is lit.

1. Remove the lower rack and unscrew the reservoir cap

(anticlockwise).

2. Only the rst time you do this: ll the salt reservoir

with water.

3. Position the funnel and ll the salt reservoir (see gure)

right up to its edge (approximately 1 kg); it is not unu-

sual for a little water to leak out.

4. Remove the funnel and wipe any salt residue away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get into

the container during the wash program (this could damage the water

softener beyond repair).

Whenever you need to add salt, it is mandatory to complete the proce-

dure before the beginning of the washing cycle to avoid corrosion.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid

dispenser A should be lled when the RINSE AID

REFILL indicator light in the control panel is lit.

NEVER pour the rinse aid directly into the

appliance tub.

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser use the opening device C. Introduce the

detergent into the dry dispenser only. Place the amount of detergent for D

pre-washing directly inside the tub.

If all-in-one detergents are used, we recommend using the TABLET button,

because it adjusts the program so that the best washing and drying results

are always achieved.

Usage of detergent not designed for dishwashers may cause malfunc-

tion or damage to the appliance.

WATER SOFTENING SYSTEM

Water softener automatically reduces water hardness, consequently pre-

venting scale buildup on heater, contributing also to better cleaning e-

ciency. This system regenerates itself with salt, therefore it is required

to rell salt container when empty.

Frequency of regeneration depends on water hardness level setting - regen-

eration takes place once per 6 Eco cycles with water hardness level set to 3.

Regeneration process starts in nal rinse and nishes in drying phase, be-

fore cycle ends.

• Single regeneration consumes: ~3.5L of water;

• Takes up to 5 additional minutes for the cycle;

• Consumes below 0.005kWh of energy.

Program Programs description

Drying

phase

ActiveDry

Available

options *)

Duration

of wash

program

(h:min)**)

Water

consumption

(litres/cycle)

Energy

consumption

(kWh/cycle)

Eco 50°- Eco program is suitable to clean normally soiled

tableware. that for this use. it is the most ecient program in

terms of its combined energy and water consumption. and that

it is used to assess compliance with the EU Ecodesign legislation. 3:10 9.5 0.85

2. Auto Intensive 65° - Automatic program for heavily soiled

dishes and pans (not to be used for delicate items). 2:00 - 3:10 14.0 - 17.0 1.50 - 1.85

3. Auto Mixed 55° - Automatic program for normally soiled pans

and dishes. 1:30 - 2:30 14.5 - 16.0 1.15 - 1.30

Auto Fast Wash 50° - Automatic program for limited quantity

of normally soiled crockery. Ensures optimal cleaning

performance in shorter time. - - 0:55 - 1:20 13.0 - 14.5 1.15 - 1.25

5. Rapid 30’ 50° - Program to be used for half load of lightly-soiled

dishes with no dried food residues. Does not have drying phase. -- 0:30 9.0 0.50

Good Night 50° - Suitable for night-time operation of the

appliance. Ensures optimal cleaning and drying performance

with the lowest noise emission. 3:30 15.0 1.15

Sanitizing 65° - Normally or heavily soiled crockery, with

additional antibacterial wash. Can be used to perform

maintenance of the dishwasher. - 1:40 10.0 1.30

8. Soak - Use to refresh crockery planned to be washed later.

No detergent to be used with this program. -- 0:12 4.5 0.01

Self-Clean 65° - Program to be used to perform maintenance

of the dishwasher, to be carried out only when the dishwash-

er is EMPTY using specic detergents designed for dishwash-

er maintenance.

-- 0:50 8.0 0.85

CONTROL PANEL

FIRST TIME USE

PROGRAMS TABLE

1. On-O/Reset button with indicator light

2. Program selection button

3. Salt rell indicator light

4. Rinse Aid rell indicator light

5. Program number and delay time indicator

6. Tablet (Tab) indicator light

7. Display

8. Zone Wash 3D indicator lights

9. Zone Wash 3D button

10. Delay button

11. START/Pause button with indicator light

/ Tablet (Tab)

1 2 3 4 5 6 7 8 9 10 11

Quick Guide

TABLET (Tab) If you use powder or liquid detergent, this option -

should be o.

OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected

program (see PROGRAMS TABLE), the corresponding LED ashes rapidly 3 times and beeps will sound. The option will not be enabled.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.

Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com

Pre-treatment of the dishes is not needed before any of the programs.

*) Not all options can be used simultaneously.

**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and

pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor cali-

bration. The sensor calibration can increase program duration up to 20 min.

ZONE WASH 3D - Option works with one rack at once. In particular,

we recommend to use it with Mixed and Intensive cycles - thanks to

the additional 3D water jets placed on the bottom o the cavity, ZONE

WASH 3D option allows to save energy or to increase the washing

performance of the dishwasher.

LOADING THE RACKS CAPACITY: 14 standard place-settings

CLEANING AND MAINTENANCE More information in the Daily Reference Guide on website.

OPTIONS AND FUNCTIONS Please scan the on your product in order to have more detailed information. QR code

ActiveDry - is a convection drying system which automatically opens the

door during/after the drying phase to ensure exceptional drying perfor-

mance every day. The door opens at a temperature that is safe to your

kitchen furniture.

CLEANING THE FILTER ASSEMBLY CLEANING THE SPRAY ARMS

In case you nd foreign objects (such as broken glass, porcelain, bones, fruit seeds

etc.) please remove them carefully.

NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).

To remove the upper spray arm,

turn the plastic locking ring in a

clockwise direction.

The lower spray arm may

be removed by pulling it

upwards.

DELAY - The start time of the program may be delayed for a period of

time between and hours.1 12

The DELAY function cannot be set once a program has been started.

ZONE WASH 3D

Zone Wash 3D uses addi-

tional water jets located

both: in the lower and

upper part of the di-

shwasher (marked with

orange color) to wash

more intensively heavily

soiled items by increa-

sing water coverage on

dishes.

LOWER RACK

For pots, lids, plates,

salad bowls, cutlery

etc. Large plates and

lids should ideally be

placed at the sides to

avoid interferences

with the spray arm.

The lower rack has

tip-up supports

which can be used

in a vertical position

when arranging pla-

tes or in a horizontal

position (lower) to

load pans and salad

bowls easily.

CUTLERY RACK

(loading example for the

cutlery rack)

The third rack was designed

to house the cutlery.

UPPER RACK

(loading example for the

upper rack)

Load delicate and light

dishes: glasses, cups,

saucers, low salad bowls.

FOLDABLE

FLAPS WITH

ADJUSTABLE

POSITION

(loading example for the

lower rack)

Produkt Specifikationer

Mærke:	Hotpoint
Kategori:	Opvaskemaskine
Model:	H0I D534A S

Har du brug for hjælp?

Hvis du har brug for hjælp til Hotpoint H0I D534A S stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Opvaskemaskine Hotpoint Manualer

Hotpoint H8F HP51BS UK Manual

25 Juli 2025

Hotpoint H8F HP51X UK Manual

25 Juli 2025

Hotpoint HA7IA15B2M6LS0 Manual

16 Juli 2025

Hotpoint HA6IB16B2M6LS0 Manual

16 Juli 2025

Hotpoint HA6IC16B4M6H0 Manual

16 Juli 2025

Hotpoint HA2IE10CS80 Manual

15 Juli 2025

Hotpoint HSIC 3M27 C S Manual

15 Juli 2025

Hotpoint HA4ID11CS80 Manual

20 Juni 2025

Hotpoint HA6IB16B2M6L0 Manual

19 Juni 2025

Hotpoint HA6IA14BN7A0 Manual

18 Juni 2025

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

BEKO BDFS16030W Manual

30 Juli 2025

BEKO BDFN36540PA Manual

30 Juli 2025

BEKO BDFN15440B Manual

30 Juli 2025

Fisher & Paykel DW60U4EI3 Manual

30 Juli 2025

BEKO BDFN26451W Manual

30 Juli 2025

BEKO BDFN15440G Manual

30 Juli 2025

Haier XF 4A4M0W-80 Manual

30 Juli 2025

BEKO BDFN15440W Manual

30 Juli 2025

Kernau KDI 6753 Manual

29 Juli 2025

Candy CH 3E7F0S Manual

29 Juli 2025