Hotpoint H7F HS41 UK Manual

Hotpoint Opvaskemaskine H7F HS41 UK

Læs gratis den danske manual til Hotpoint H7F HS41 UK (8 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Hotpoint H7F HS41 UK, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

ENDaily Reference Guide

CONTROL PANEL

THANK YOU FOR BUYING A HOTPOINT PRODUCT.

In order to receive a more complete assistance, please

Before using the appliance carefully read Safety

and Installation Instructions. More information about your product

available on website: docs.hotpoint.eu

After installation, please remember to remove all transport protection

parts from the dishwasher.

SETTING MENU

1. Switch on the appliance by pressing the button.ON-OFF

2. Hold the Settings (Half Load ) button for 3 seconds until you hear

a beep.

3. After one second the rst available setting (letter „h”) will be displayed.

4. Press button to scroll through the list of available settings (see table

below), then press START/Pause to view and change the value of the

currently selected setting.

5. Press to change the value, then press START/Pause to save the

new value.

6. To change another setting, repeat points 2 and 5.

7. Press or wait 30 seconds to exit the menu.ON-OFF

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and the

machine’s functional components.

The salt reservoir is located in the lower part of the dishwasher (under the

lower rack on the left side).

• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.

• It is important to set the water hardness.

• Salt must be lled when the SALT REFILL indicator light on the

control panel is lit.

1. Remove the lower rack and unscrew the reservoir cap

(anticlockwise).

2. Position the funnel and ll the salt reservoir (see gure)

right up to its edge (approximately kg); it is not 0,5

unusual for a little water to leak out.

3. Only the rst time you do this: ll the salt reservoir

with water.

4. Remove the funnel and wipe any salt residue away from the opening.

Make sure the cap is screwed on tightly so that no detergent can get into

the container during the wash program (this could damage the water

softener beyond repair).

Run a program every time as soon as you completed relling the salt

reservoir to avoid corrosion.

Setting the water hardness

To allow the water softener to work in a perfect way, it is essential that the water

hardness setting is based on the actual water hardness in your house. This infor-

mation can be obtained from your local water supplier. The factory setting is “3”.

See „WATER HARDNESS TABLE”.

To change, follow instructions in section „SETTING MENU”.

LETTER SETTING VALUES

(Default - )in bold

Water Hardness Level

(see “SETTING THE WATER HARDNESS”

and “WATER HARDNESS TABLE”) 1 | 2 | | 4 | 53

Rinse Aid Level

(see “ADJUSTING THE DOSAGE OF RINSE AID”) 0 | 1 | 2 | 3 | 4 | 5

ActiveDry (see “OPTIONS AND FUNCTIONS”)

“1” = On, “0” = O 1 | 0

Sound

“1” = On, “0” = O 1 | 0

Factory Settings

Press START/Pause to restore to the factory

default all the values of the settings included

in the settings menu.

Only use salt that has been specically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL indicator

light switches o.

If the salt container is not lled, the water softener and the heating

element may be damaged as a result of limescale accumulation.

Use of salt is recommended with any type of dishwasher detergent.

WATER SOFTENING SYSTEM

Water softener automatically reduces water hardness, consequently preventing

scale buildup on the heater, contributing also to better cleaning eciency.

This system regenerates itself with salt, therefore it is required to rell

the salt container when empty. The frequency of regeneration depends

on the water hardness level setting - regeneration takes place once per 4-6

Eco cycles with the water hardness level set to . The regeneration process 3

occurs at the beginning of the cycle with additional fresh water.

• Single regeneration consumes: ~3L of water;

• Takes up to 5 additional minutes for the cycle;

• Consumes below 0.005kWh of energy.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser should be lled A

when the in the control panel is lit.RINSE AID REFILL indicator light

1. Open the dispenser B by

pressing and pulling up the

tab on the lid.

2. Pour in the rinse aid (max. 110

ml), making sure it does not

overow from the dispenser.

If this happens, clean the spill

immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

Adjusting the dosage of rinse aid

If you are not completely satised with the drying results, you can adjust

the quantity of rinse aid used.

To change, follow instructions in the section .„SETTING MENU”

If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW

RINSE AID indicator light will not be lit if you run out of rinse aid.

A maximum of levels can be set according to the dishwasher model.6

• If you see bluish streaks on the dishes, set a low number (0-3).

• If there are drops of water or limescale marks on the dishes, set

a mid-range number (4-5).

FIRST TIME USE

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

°Clark

English degrees

1 (soft) 0 - 6 0 - 10 0 - 7

2 (medium) 7 - 11 11 - 20 8 - 14

3 (average) 12 - 16 21 - 29 15 - 20

4 (hard) 17 - 34 30 - 60 21 - 42

5 (very hard) 35 - 50 61 - 90 43 - 62

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

1. ON-OFF/Reset button with indicator light

2. Eco program button with indicator light

3. Auto Intensive program button with indicator light

4. Auto Mixed program button with indicator light

5. Auto Fast program button with indicator light

6. Rapid program button with indicator light

7. Delicates

program button with indicator light

8. Soak program button with indicator light

9. Salt reservoir empty indicator light

10. Rinse Aid reservoir empty indicator light

11. Display

12. Program number remaining time and indicator

13. Closed water tap indicator light

14. DESCALE indicator light

15. 3D Zone Wash option button with indicator light

16. Half Load option Settings button with indicator light/ - 3 sec. press

17. Extra Dry option button with indicator light

18. Silent option Key lock button with indicator light/ - 3 sec. press

19. Sani Rinse option button with indicator light

20. Self-Clean program button with indicator light

21. Delay option button with indicator light

22. START/Pause button with indicator light

Produkt Specifikationer

Mærke:	Hotpoint
Kategori:	Opvaskemaskine
Model:	H7F HS41 UK

Har du brug for hjælp?

Hvis du har brug for hjælp til Hotpoint H7F HS41 UK stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Opvaskemaskine Hotpoint Manualer

Hotpoint HA2FFC14BX Manual

8 Oktober 2025

Hotpoint HA2FFD14BX Manual

8 Oktober 2025

Hotpoint HI 3010 Manual

2 August 2025

Hotpoint HSIO 3O23 WFE dishwasher Manual

2 August 2025

Hotpoint HIC 3O33 WLEG Manual

1 August 2025

Hotpoint HFC 2B19 X Manual

1 August 2025

Hotpoint HIC 3C41 CW Manual

1 August 2025

Hotpoint HFC 3C32 WX Manual

1 August 2025

Hotpoint HIC 3C34 Manual

1 August 2025

Hotpoint HSIC 3T127 C Manual

1 August 2025

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Infiniton DIW-6115BD3 Manual

5 November 2025

KitchenAid KDFS424SPS Manual

5 November 2025

KitchenAid KDTS724SPS Manual

4 November 2025

KitchenAid KDFS424SBE Manual

4 November 2025

Icecool LVI60E Manual

4 November 2025

Elektra Bregenz GIV 56480 X Manual

3 November 2025

Frigor OP700S Manual

3 November 2025

Whirlpool WIP 4T233 PFEG B Manual

3 November 2025

Big Chill BC24DWCCPMW Manual

3 November 2025

Big Chill BC24DWCSNSB Manual

3 November 2025