Hotpoint HA6FA14BN7A0X Manual

Hotpoint Opvaskemaskine HA6FA14BN7A0X

Læs gratis den danske manual til Hotpoint HA6FA14BN7A0X (8 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Hotpoint HA6FA14BN7A0X, eller vil du spørge andre brugere om produktet?

Side 1/8
ENQuick Guide
1
THANK YOU FOR BUYING A HOTPOINT ARISTON PRODUCT.
In order to receive a more complete assistance, please register
your appliance on: www.hotpoint.eu/register
Before using the appliance carefully read Safety Instructions guide.
PLEASE SCAN THE QR CODE ON YOUR
APPLIANCE IN ORDER TO HAVE MORE
DETAILED INFORMATION
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
It is mandatory that the salt reservoir never be empty.
It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher and must be
lled when the SALT REFILL indicator light in the control panel is lit.
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel and ll the salt reservoir (see gure)
right up to its edge (approximately 1 kg); it is not unu-
sual for alittle water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get into
the container during the wash program (this could damage the water sof-
tener beyond repair).
Whenever you need to add salt, it is mandatory to complete the pro-
cedure before the beginning of the washing cycle to avoid corrosion.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently prevent-
ing scale buildup on heater, contributing also to better cleaning eciency.
This system regenerates itself with salt, therefore it is required to rell
salt container when empty.
Frequency of regeneration depends on water hardness level setting - regen-
eration takes place once per Eco cycles with water hardness level set to . 6 3
Regeneration process starts in nal rinse and nishes in drying phase, be-
fore cycle ends.
Single regeneration consumes: ~3.5L of water;
Takes up to 5 additional minutes for the cycle;
Consumes below 0.005kWh of energy.
A
C
D
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid
dispenser Ashould be lled when the RINSE AID
REFILL indicator light in the control panel is lit.
NEVER pour the rinse aid directly into the ap-
pliance tub.
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device . Introduce the C
detergent into the dry dispenser only. Place the amount of detergent for D
pre-washing directly inside the tub.
The detergent dispenser automatically opens up at the right time accord-
ing to the program.
If all-in-one detergents are used, we recommend using the TABLET button,
because it adjusts the program so that the best washing and drying results
are always achieved Usage of detergent not designed for dishwashers
may cause malfunction or damage to the appliance.
Program Programs description
Drying
phase
ActiveDry
Available
options *)
Duration
of wash
program
(h:min)**)
Water
consumption
(litres/cycle)
Energy
consump-
tion
(kWh/cycle)
1.
Eco 50°- Eco program is suitable to clean normally soiled table-
ware. that for this use. it is the most ecient program in terms of
its combined energy and water consumption. and that it is used
to assess compliance with the EU Ecodesign legislation.
4:50 9.5 0.54
2. Auto Intensive 65° - Automatic program for heavily soiled dish-
es and pans (not to be used for delicate items). 2:00 - 3:10 14.0 - 17.0 1.50 - 1.85
3. Auto Mixed 55° - Automatic program for normally soiled pans
and dishes. 1:30 - 2:30 14.5 - 16.0 1.15 - 1.30
4.
Auto Fast Wash 50° - Automatic program for limited quantity
of normally soiled crockery. Ensures optimal cleaning perfor-
mance in shorter time. 0:55 - 1:20 11.0 - 14.5 1.15 - 1.25
5. Rapid 30’ 45° - Program to be used for half load of lightly-soiled
dishes with no dried food residues. Does not have drying phase. - 0:30 9.0 0.50
6.
Good Night 5- Suitable for night-time operation of the ap-
pliance. Ensures optimal cleaning and drying performance with
the lowest noise emission. 3:30 16.0 1.15
7.
Sanitizing 65° - Normally or heavily soiled crockery, with addi-
tional antibacterial wash. Can be used to perform maintenance
of the dishwasher. - 1:40 12.0 1.30
8. Soak - Use to refresh crockery planned to be washed later.
No detergent to be used with this program. -- 0:12 4.5 0.01
9.
Self-Clean 65° - Program to be used to perform maintenance of the
dishwasher, to be carried out only when the dishwasher is EMPTY
using specic detergents designed for dishwasher maintenance.
-- 0:50 8.0 0.85
CONTROL PANEL
FIRST TIME USE
PROGRAMS TABLE
3
1
2
8
13
1454 6 7 11 129 10
1. On-O / Reset button with indicator light
2. Program selection button with indicator light
3. 3D Zone Wash button with indicator light / Keylock
4. Eco program indicator light
5. Keylock indicator light
6. Display
7. Program number and remaining time indicator
8. Tablet (Tab) indicator light
9. Closed water tap indicator light
10. Rinse Aid rell indicator light
11. Salt rell indicator light
12. Short Time button with indicator light / Tablet (Tab)
13. Delay button with indicator light
14. Start/Pause button with indicator light / Drain out
2
Quick Guide
EN
TABLET (Tab) If you use powder or liquid detergent, this option -
should be o.
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected
program (see PROGRAMS TABLE), the corresponding LED ashes rapidly 3 times and beeps will sound. The option will not be enabled.
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.
Note for Test Laboratories: For information on
comparative EN testing conditions, please send an email to the following address: dw_test_support@europeanappliances.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and
pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor cali-
bration. The sensor calibration can increase program duration up to 20 min.
3D ZONE WASH - Option works with one rack at once. In particular,
we recommend to use it with Mixed and Intensive cycles - thanks to
the additional 3D water jets placed on the bottom o the cavity, 3D ZONE
WASH option allows to save energy or to increase the washing performance
of the dishwasher.
CLEANING AND MAINTENANCE More information in the Daily Reference Guide on website.
OPTIONS AND FUNCTIONS Please scan the on your product in order to have more detailed information. QR code
ActiveDry - is a convection drying system which automatically opens the
door during/after the drying phase to ensure exceptional drying perfor-
mance every day.
The door opens at a temperature that is safe to your kitchen furniture, thus
door will not be opened when the option of SHORT TIME is on.
SHORT TIME - This option can be used to reduce the duration of the
main programs while maintaining the same washing and drying per-
formance levels.
CLEANING THE FILTER ASSEMBLY CLEANING THE SPRAY ARMS
A
A
B
C
In case you nd foreign objects (such as broken glass, porcelain, bones, fruit seeds etc.)
please remove them carefully.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
To remove the upper spray arm,
turn the plastic locking ring in a
clockwise direction.
The lower spray arm may be
removed by pulling it up-
wards.
DELAY -The start of the program may be delayed for a period of time
between and hours.0:30 24
The DELAY function cannot be set once a program has been started.
KEYLOCK - A long press (for 3 seconds) of 3D ZONE WASH button, will
activate the KEYLOCK function. To deactivate the KEYLOCK, long press again.
CUTLERY RACK
The third rack was designed to
house the cutlery.
(loading example for thecutlery
rack)
UPPER RACK
Load delicate and light dishes:
glasses, cups, saucers, low sal-
ad bowls.
(loading example for
theupper rack)
FOLDABLE FLAPS
WITH ADJUSTABLE
POSITION
LOADING THE RACKS CAPACITY: 14 standard place-settings
LOWER RACK
For pots, lids, plates, salad bowls, cutlery etc.
Large plates and lids should ideally be placed
at the sides to avoid interferences with the
spray arm.
The lower rack has tip-up supports which can
be used in avertical position when arranging
plates or in a horizontal position (lower) to
load pans and salad bowls easily.
(loading example for the lower rack)
ZONE WASH 3D
3D Zone Wash uses additional water jets located both: in
the lower and upper part of the dishwasher (marked with
orange color) to wash more intensively heavily soiled
items by increasing water coverage on dishes.
GLASS CARE
2 3
1
1
3
2
A
B
Dedicated accessory that allows you to
safely store dierent types of stem glasses
in the lower rack. It enables cleaning &
drying results by allowing an optimised
and stable positioning of the glasses.


Produkt Specifikationer

Mærke: Hotpoint
Kategori: Opvaskemaskine
Model: HA6FA14BN7A0X

Har du brug for hjælp?

Hvis du har brug for hjælp til Hotpoint HA6FA14BN7A0X stil et spørgsmål nedenfor, og andre brugere vil svare dig