Hotpoint HZ1422.1 Manual

Hotpoint Fryser HZ1422.1

Læs gratis den danske manual til Hotpoint HZ1422.1 (12 sider) i kategorien Fryser. Denne vejledning er vurderet som hjælpsom af 45 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 23 anmeldelser. Har du et spørgsmål om Hotpoint HZ1422.1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

FREEZER

HZ1422.1

KSZ1422.1

Operating Instructions

English

Contents

Installation, 2-3

Positioning and connection

Description of the appliance, 4

Overall view

Start-up and use, 5

Starting the appliance

Using the freezer to its full potential

Maintenance and care, 6

Switching the appliance off

Cleaning the appliance

Avoiding mould and unpleasant odours

Defrosting the appliance

Precautions and tips, 7

General safety

Disposal

Respecting and conserving the environment

Troubleshooting, 8

Guarantee, 9

After Sales Service, 10

appliance now on

08448 24 24 24

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24

Installation

Your appliance is supplied with a 13amp fused plug that

can be plugged into a 13amp socket for immediate use.

Before using the appliance please read the instructions

below.

WARNING:

THIS APPLIANCE MUST BE EARTHED.

Replacing fuse covers:

When replacing a faulty fuse, a 13amp ASTA approved

fuse to BS 1362 should always be used and the fuse

cover re-fitted.

If the fuse cover is lost, the plug must not be used until a

replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking or the

colour that is embossed in words on the base of the plug.

Changing the plug:

Removing the plug

If your appliance has a non-rewireable moulded plug and

you should wish to remove it to add a longer cable or

to re-route the mains cable through partitions, units etc.

please ensure that either:

- The plug is replaced by a fused 13amp re-

wireable plug bearing the BSI mark of

approval.

- The mains cable is wired directly into a

13amp cable outlet, controlled by a

switch (in compliance with BS 5733)

which is accessible without moving the

appliance.

Disposing of the plug

Cut off and dispose of the supplied plug if it does not

fit your socket. The cable should be cut as close as

possible to the moulded plug.

Remove the fuse.

WARNING:

To avoid a shock hazard do not insert the discarded

plug into a socket anywhere else.

Fitting a new plug

! Before placing your new appliance into operation

please read these operating instructions carefully. They

contain important information for safe use, for installation

and for care of the appliance.

! Please keep these operating instructions for future

reference. Pass them on to possible new owners of the

appliance.

Positioning and connection

Positioning

1. Place the appliance in a well-ventilated humidity-free room.

2. Do not obstruct the rear fan grills. The compressor and

condenser give off heat and require good ventilation to

operate correctly and save energy.

3. Ensure the appliance is away from any sources of heat

(direct sunlight, electric stove, etc.).

Electrical connections

After the appliance has been transported, carefully place

it vertically and wait at least 3 hours before connecting it

to the electricity mains. Before inserting the plug into the

electrical socket ensure the following:

• The appliance is earthed and the plug is compliant

with the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate located

inside the freezer (e.g. 150 W).

• The voltage is in the range of values indicated on the

data plate located inside the freezer (e.g. 220-240V).

• The socket is compatible with the plug of the appliance. If

the socket is incompatible with the plug, ask an authorised

technician to replace it ( ). Do not use see Assistance

extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should these

safety measures not be observed.

Produkt Specifikationer

Mærke:	Hotpoint
Kategori:	Fryser
Model:	HZ1422.1
Bredde:	540 mm
Dybde:	550 mm
Højde:	870 mm
Produktfarve:	Hvid
Kontroltype:	Dreje
Produkttype:	Stående
Pakkedybde:	610 mm
Pakkebredde:	570 mm
Pakkehøjde:	920 mm
Energieffektivitetsklasse (gammel):	A+
Årligt energiforbrug:	190 kWh
Placering af apparat:	Indbygget
Indvendig belysning:	Ja
Dørhængsel:	Højre
Støjniveau:	39 dB
Vendbare døre:	Ja
Fryser, netto rumindhold:	84 L
Fryser, brutto rumindhold:	102 L
Frysekapacitet:	5 kg/24t
Opbevaringstid under strømafbrydelse:	14 t
Klimaklasse:	SN-T
Brugerdefineret panel klar:	Ingen
Stjernebedømmelse:	4*
Hurtig frys funktion:	Ja
Fryser antal hylder/kurve:	4
Isterning bakke:	Ja