Hubbell J1639T Manual

Hubbell Varmeapparat J1639T

Læs gratis den danske manual til Hubbell J1639T (5 sider) i kategorien Varmeapparat. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Hubbell J1639T, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

OPERATING AND MAINTENANCE

MANUAL FOR

ELECTRIC BOOSTER HEATER

ELECTRIC HEATER COMPANY

BASE MODEL “ J ”

UM ANSI/NSF5

201 Edition7

OPTIONAL FIELD CONVERSION FROM SINGLE TO THREE PHASE OR

THREE TO SINGLE PHASE (J6 and J16 models in 6, 7, and 9 kW at 208 and 240

volts and J411 models only)

1. Re-wire the unit to desired configuration as indicated below.

NOTE: The wire to be used for internal wiring must conform to SEW-2 or PTFE

(200°C) and must match the wire size currently in use. Contact the factory for

assistance, if required.

2. Contact the factory for correct labels. The factory will need the serial number for

proper identification.

Single-Phase 3-Phase

OPTIONAL 24-VOLT HEATER INTERLOCK ADAPTER

1. If desired, the heater can be wired to operate only when supplied with a 24-volt signal

through the heater interlock adapter. When no 24-volt signal is supplied through the

heater interlock adapter the heater is interlocked and will not energize. When

interlocked the display will show “ HLd”. The heater will resume normal operation

when a 24-volt signal is re-applied through the heater interlock adapter.

2. To utilize this feature, plug the 24-volt heater interlock adapter into terminal J1 of the

T1000 control board (note: if the XB1 expansion board is used, plug the adapter into

terminal JX3 of the XB1) and verify that the configuration is set to “ Hon”, see the

controller operation section for further detail. The signal can be either AC or DC.

However, if a DC signal is utilized and the interlock feature does not operate, switch

the two 24-volt supply wires at the heater interlock adapter.

FINAL CHECKS

1. Check all connections for tightness.

2. Ensure that all the above steps are completed.

3. Remove the protective outer plastic covering from the sheet metal shell.

4. After the water is heated for the first time, monitor the water temperature as described

in Section III, Annual Inspection.

To J1

To 24-Volt Si

nal

Produkt Specifikationer

Mærke:	Hubbell
Kategori:	Varmeapparat
Model:	J1639T

Har du brug for hjælp?

Hvis du har brug for hjælp til Hubbell J1639T stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Varmeapparat Hubbell Manualer

Hubbell J1610S Manual

21 August 2024

Hubbell J1658T4 Manual

21 August 2024

Hubbell J610T4 Manual

21 August 2024

Hubbell J66T Manual

20 August 2024

Hubbell J167T Manual

20 August 2024

Hubbell J65T4S Manual

20 August 2024

Hubbell J1639R Manual

20 August 2024

Hubbell J630T Manual

19 August 2024

Hubbell J1636T Manual

19 August 2024

Hubbell J67RS Manual

19 August 2024

Varmeapparat Manualer

Nyeste Varmeapparat Manualer

Klarstein Wonderwall Air 60 Manual

30 Juli 2025

Panasonic NF-GM600 Manual

29 Juli 2025

Heatstrip THSTAND Manual

29 Juli 2025

Heatstrip Intense Manual

29 Juli 2025

Rowenta Auto Confort BU7500 Manual

29 Juli 2025

TriStar KA-5877 Manual

28 Juli 2025

TriStar KA-5866 Manual

27 Juli 2025

TriStar KA-5869 Manual

27 Juli 2025

Sencor SOH 3111BK Manual

27 Juli 2025

Sencor SOH 3011BE Manual

26 Juli 2025