Ice-O-Matic B1300-48 Manual
Ice-O-Matic
Ismaskine
B1300-48
Læs nedenfor 📖 manual på dansk for Ice-O-Matic B1300-48 (12 sider) i kategorien Ismaskine. Denne guide var nyttig for 4 personer og blev bedømt med 4.4 stjerner i gennemsnit af 2.5 brugere
Side 1/12
1
Ice-O-Matic Upright Ice Storage Bins with Ice Shield
Installation Instructions and Parts List
Ice-O-Matic ice storage bins enjoy a well-deserved reputation for excellent performance, long-term reliability and
outstanding after-the-sale support. To ensure that this bin delivers that same degree of service, we ask that you
take a moment to review this instruction before beginning the installation of the bin. Should you have any
questions or require technical help at any point, please call our technical service group at (800)423-3367
(US & Canada)
Before You Begin.
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If
damage is found, notify the shipper immediately and contact Ice-O-Matic so that we can help in the filing of a
claim, if necessary.
!
Important Cautions
• Avoid excessive tightening force when connecting to the bin drain fitting
• Do not apply excessive heat if any sweating of fittings is necessary. Heat conduction through metal may melt
threads in plastic drain fitting.
• When leveling, do not extend any leg more than 1 in. (26mm) for total leg height no greater than
2.125 in. (54mm).
Installation
1. Remove all packing material from bin.
2. Remove all tape and temporary fastenings from door assemblies and outside of bin.
3. Remove set of four legs and any other accessories packed inside bin.
4. Lay bin on back, being careful to protect finish, and remove bolts holding skid to bin.
5. Screw legs into tapped holes in bin bottom and tighten to seat legs well against bottom.
6. Set bin upright.
7. Remove protective paper from stainless steel exterior.
8. Move bin to permanent location.
9. Adjust “foot” at bottom of each leg to level bin in both directions.
10. Mount icemaker(s) on bin in accordance with icemaker manufacturer's instructions.
11. Connect drain line to 1" FPT female fitting located in bottom of bin.
12. Make final connections to icemaker. (Reference the Ice-O-Matic Installation Manual)
11100 East 45th Ave.
Denver CO 80239
800 423-3367
EP 2138774
Bin Model Numbers www.iceomatic.com 9081461-01
B700-30, B1000-48, B1300-48, B1325-60, B1600-60 01078856R00
12/14
2
Removing L ower
Door Assemb
l
y
(Only if required for access through narrow doors)
1. With door in closed position, remove Phillips head screw and washer from hinge area on each side of lower
access door.
2. Insert screwdriver between door and hinge bracket on one side of door and gently push against bracket to
provide room for
door stud to clear bracket.
3.
Remove
access door.
4.
Pull
up on
Ice Shied
t
o
r
emo
v
e
.
5.
Remove screws along
t
op
of
door
assemb
l
y
.
6.
Pull forward
on
t
op
of
assemb
l
y
and lift
t
o
r
emo
v
e
.
Reinstalling Door Assembly
1. Reinstall lower door assembly in bin opening.
2. Reinstall screws in hood at top of door assembly.
3. Reinstall Ice Shield in side panel tracks and push down to
seat.
4. With door in closed position, insert one door stud through
hinge bracket, install washer, screw and tighten.
Note: For proper operation the access door must be reinstalled in the closed position.
5. On other side, insert screwdriver between door and hinge bracket and gently push against bracket to provide
room for door stud to clear bracket.
6. Reinstall washer and screw in lift door and tighten.
7. Check door to ensure proper operation.
Operation
Ice Shield Operation
Ice-O-Matic’s unique Ice Shield positively controls the flow of ice into lower door assembly area for removal with
either a scoop or shovel.
Ice Shield can also be adjusted and locked at one of several levels to accommodate flow characteristics of
different types of ice.
Bin is shipped with Ice Shield in full down position. The Ice Shield can be raised and locked in higher position
for better flow or when more access is needed.
If More Ice Is Needed In Lower Door Area:
1. Use full-length handle at top of Ice Shield to gently lift and jiggle the Ice Shield to encourage ice to flow into
access area of the bin (Fig. 1). (Loose ice will cascade into lower door area.)
2. When adequate ice has flowed, push the Ice Shield back down.
When More Access Is Needed Or To Encourage Flow Of Less Ice:
1. Lock gate at higher level by pulling up and holding the
Ice Shield at correct level, and pushing tapered end of catch into nearest hole in gate
(catch will automatically release when you pull up).
2. To release catch, pull up on the Ice Shield.
Fig.
1
Produkt Specifikationer
| Mærke: | Ice-O-Matic |
| Kategori: | Ismaskine |
| Model: | B1300-48 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Ice-O-Matic B1300-48 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ismaskine Ice-O-Matic Manualer
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
Ismaskine Manualer
- Ismaskine Focus Electrics
- Ismaskine Jocel
- Ismaskine Maytag
- Ismaskine Duronic
- Ismaskine Avantco
- Ismaskine ECG
- Ismaskine Domoclip
- Ismaskine Whirlpool
- Ismaskine GlobalTronics
- Ismaskine Emerio
- Ismaskine Termozeta
- Ismaskine Caso
- Ismaskine Team
- Ismaskine Frigidaire
- Ismaskine Blaupunkt
Nyeste Ismaskine Manualer
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025