IFi Audio Hip dac 3 Manual

IFi Audio Ikke kategoriseret Hip dac 3

Læs gratis den danske manual til IFi Audio Hip dac 3 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 14 anmeldelser. Har du et spørgsmål om IFi Audio Hip dac 3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

8. USB-C data input port

Connect your phone to the hip dac 3 with a Lightning to USB

Camera Adapter (Apple) or USB-C to USB-C cable (Android).

When using other audio sources, please connect with a USB

cable. This USB-C port is intended for data transfer only.

Tip: For Apple iOS and Android devices, please use battery power on the hip dac 3,

otherwise you may receive error messages from your device.

Note: For use with PC it is necessary to download drivers.

Tip: For the required driver and all the latest firmware updates please refer to our

website: www.ifi-audio.com/download-hub/

9. USB-C (5V) battery charge input

For charging only. It will take ~3 hours for a high-powered USB

charger to fully charge hip dac 3. Use the enclosed USB 'Type A'

to 'Type C' cable, smart charger or a regular charger up to 6.3V.

10. LED for Battery Status

LED Status

White* > 75%

Green* 25% >

Red* 10% >

Red (flashing) 10% ≤

*Battery LED will flash when it is charging

ifi-audio.com

Ver1.0

31 2 5 64

4. ON/OFF and Analogue Volume Control

The analogue volume control in hip dac 3 is superior to any digital

volume control.

Warning: Due to the high power of hip dac 3, always start off at a low volume level

so that there is no risk of damage to your headphones and your hearing. iFi audio is

not responsible for any hearing or equipment damage from misuse.

Power ON. Power OFF.

Tip: hip dac 3 will continue to use battery power even if the USB cable is connected

afterwards.

Tip: For connection to Apple devices, Apple Lightning to USB Camera Adapter is

required. For connection to Android devices, USB-C to USB-C cable and

appropriate OS support are required.

For more information, please refer to www.ifi-audio.com

5. Balanced 4.4mm headphone output

Connect balanced 4.4mm headphones.

6. S-Balanced 3.5mm headphone output

Connect 3.5mm headphones.

7. iEMatch switch

iEMatch reduces the output level, so that even the most

sensitive In-Ear-Monitors (IEMs) can be matched to the hip dac 3.

= 3.5mm headphones

= off

= 4.4mm headphone

Tip: The hip dac 3 or the headphone will not be damaged if the iEMatch switch is adjusted incorrectly,

but the attenuation level will not be correct.

98 10

OFF

1. PowerMatch (on/off )

PowerMatch enables hip dac 3 to match headphones' impedance

and sensitivity in order to generate their highest operational

efficiency.

Tip: For in-ear-monitors (earbuds) try PowerMatch off. For headphones try PowerMatch on,

When on, the gain increases by 10dB. If your IEMs are very sensitive, try using the iEMatch

feature (item 7).

2. XBass (on/off)

Many headphones lack the correct bass response. XBass is an

analogue circuit designed to 'add back' the lost bass response for a

more accurate reproduction of the original music.

3. Audio Format LED (kHz)

The LED colour scheme indicates the audio format and sampling

frequency received by hip dac 3 from the music source.

LED Mode

Yellow PCM 44.1/48kHz

White PCM 88.2/96/176.4/192/352.8/384kHz

Cyan DSD 64/128

Red DSD 256

Green MQA

Blue MQA Studio

Magenta Original Sample Rate*

*MQB

Warning: Installing GTO enabled firmware may result in the LED's on this device no longer

changing in accordance with the above table

iE Ma tc h

of f

3. 5

4. 4

SPECIFICATIONS

Input: USB-C

Formats supported: DSD256 / 11.3MHz

PCM 384kHz

full MQA Decoder

DAC: Bit-Perfect DSD & DXD DAC by Burr Brown

Headphone Outputs:

Balanced 4.4mm

S-BAL 3.5mm

Power Output:

Balanced 400mW @ 32 ; 6.3V @ 600Ω Ω

S-BAL 280mW @ 32 ; 3.2V @ 600Ω Ω

Output Impedance:

Balanced ≤1 , With iEMatch engaged: ≤4.5Ω Ω

S-BAL ≤1 , With iEMatch engaged: ≤4.5ΩΩ

SNR:

Balanced ≥109dB(A) @ 0dBFS

S-BAL ≥103dB(A) @ 0dBFS

DNR:

Balanced ≥109dB(A)

S-BAL ≥103dB(A

THD + N:

Balanced <0.006X% (360mW/2.0V @ 600Ω)

S-BAL <0.01% (100mW/1.27V @ 16Ω)

Frequency Response: 20Hz - 45kHz (-3dB)

Power Consumption: <2W idle, 4W max

Battery: Lithium-polymer 2200mAh approx.

8 hours

Power System: Charging via USB-C,BC V1.2 compliant up

to 1000mA charging current

Dimensions: 102 x 70 x 14 mm (4.0" x 2.8" x 0.6")

Net weight: 135 g (0.30 lbs)

Limited Warranty: 12 months*

*12 months typical or as permitted/required by local reseller laws.

**Specifications are subject to change without notice.

Produkt Specifikationer

Mærke:	IFi Audio
Kategori:	Ikke kategoriseret
Model:	Hip dac 3

Har du brug for hjælp?

Hvis du har brug for hjælp til IFi Audio Hip dac 3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret IFi Audio Manualer

IFi Audio GO blu Air Manual

17 Oktober 2025

IFi Audio Omni USB Manual

7 Oktober 2025

IFi Audio iEMatch Manual

19 Juli 2025

IFi Audio iEMatch4.4 Manual

13 Januar 2025

IFi Audio GO link Max Manual

13 December 2024

IFi Audio SupaNova Manual

18 September 2024

IFi Audio LAN iSilencer Manual

4 September 2024

IFi Audio iDSD Diablo 2 Manual

28 August 2024

IFi Audio NEO iDSD 2 Manual

27 August 2024

IFi Audio SPDIF iPurifier2 Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Philips Evnia 32M3C3540 Manual

30 Oktober 2025

Soler & Palau DUOVENT MODULAR XL DV Manual

30 Oktober 2025

Iogear GCS1228TAA3 Manual

30 Oktober 2025

Abus E212 Manual

30 Oktober 2025

Olimpia Splendid Bi2 SLIR Manual

30 Oktober 2025

EtherWAN EX24402 Manual

30 Oktober 2025

Abus Smartvest Pro APP45200 Manual

30 Oktober 2025

EtherWAN ED3501 Manual

30 Oktober 2025

Sage the Puck Sucker SCA800 Manual

30 Oktober 2025

Wimberley AP-606 Manual

30 Oktober 2025