IFM ID3508 Manual

IFM Ikke kategoriseret ID3508

Læs gratis den danske manual til IFM ID3508 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om IFM ID3508, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

TEL: 800-441-8246 • FAX: 800-329-0436

www.ifmefector.com

ifm efector

Mounting Instructions

Inductive nonflush mountable rectangular switches - adjustable / CSA Div. 2

Concerning Safety… ifm efector makes every effort to build a depend-

able product, but every product will eventually fail. Therefore, your equip-

ment must be designed to prevent property damage and personal injury

if our products fail. ifm efector proximity switches are not designed to be

used as stand-alone devices to protect or guard human life or limb.

Nonflush mountable rectangular switches should have a metal-free zone surrounding the sensing face in

accordance with the diagrams shown here.

Metal

Sensing Face

‡1.5xB

Metal

‡3xSn

‡2xB

Sensin g Face

n-target

bac

kgroun

d metal

‡2xB

B2xB

Sensing Face

Metal

8xSn

Sensing Face

B = width of sensing face

Sn = nominal sensing range

B = width of sensing face

702796/01

Adjustment to Range

Place the target in position where detection is to take place.

If the factory setting of the sensitivity adjustment has not been

disturbed, the indicator LED should be on. Factory setting of the

sensitivity range involves tuning the switch so the LED just turns

on when a target is placed at the maximum sensing range of the

switch. The target should be made of mild steel and be at least as

large as the sensing area of the switch. Further adjustment is not

usually required.

If the indicator LED is not on, the application is beyond the range

of the switch. No increase in sensitivity above this setting should

be used even it it seems to work.

If there is a known position where the switch must be off, move

the target to that position and observe that the indicator LED

turns off. If it doesn’t, decrease the sensitivity (ccw) until it turns

off and continue an additional quarter turn. Verify that it still turns

on when the target is returned to its original position.

B = width of sensing face

Sn = nominal sensing range

Wiring

The output of the switch can be programmed normally open

or normally closed. It will be shipped normally open unless

specified normally closed when ordered. To change from normally

open to normally closed, remove the wire from terminal 4 and

insert in terminal 5.

To access the terminal block, loosen the four screws on the switch

housing and remove the switch from the base. To remove or insert

a wire into the terminal block, apply firm downward pressure to

the top of one of the numbered rectangular openings with a

screwdriver or similar tool. The pressure from the screwdriver will

open the spring contact enabling you to remove or insert a wire.

ELECTRICAL

DO NOT operate an incandescent light bulb as a

load. The current inrush when the bulb is cold can

cause a current overload.

DO NOT operate a proximity sensor directly from a

voltage supply without a load. This is a short circuit

and can cause damage. Note: insert a miniature fuse

according to the technical data sheet, if specified.

WARNING

Explosion Hazard — substitution of components may impair suit-

ability of Class 1, Div. 2.

CAUTION

Nonmetallic enclosure does not provide grounding between con-

duit connections. Use grounding type bushing and jumper wires.

Use only ifm efector conduit adapters (U30029, U30030, U30031)

or other CSA certified conduit adapters.

Produkt Specifikationer

Mærke:	IFM
Kategori:	Ikke kategoriseret
Model:	ID3508

Har du brug for hjælp?

Hvis du har brug for hjælp til IFM ID3508 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret IFM Manualer

15 November 2025

15 November 2025

14 November 2025

14 November 2025

11 November 2025

10 November 2025

10 November 2025

10 November 2025

9 November 2025

9 November 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone 7800 Manual

11 December 2025

Kwikset 258 Manual

11 December 2025

Schlage F170 Manual

11 December 2025

Moen Align 7565EV Manual

11 December 2025

Energy Sistem ESG M3 Neon Manual

11 December 2025

ALNO MC10244 Manual

11 December 2025

JET TAK-ZX Manual

11 December 2025

Crosley Nashville CF1165 Manual

11 December 2025

Waterstone 1455 Manual

11 December 2025

Laica NE2015 Manual

11 December 2025