Iget SMART Security M3P1 Manual

Iget Bevægelsesdetektor SMART Security M3P1

Læs gratis den danske manual til Iget SMART Security M3P1 (2 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Iget SMART Security M3P1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation manual | Wireless Motion Sensor

Instalační manuál | Pohybový PIR detektor

Inštalačný manuál | Pohybový PIR detektor

Website : www.iget.eu E-mail : sales@iget.eu

Battery replacement instructions/ Výměna baterie/ Výmena batérie

Trigger Mode Clarication/ Funkce Trigger/ Funkcie Trigger

Trigger Mode Mód Triggeru Mód Triggeru VýznamClarification Význam

Close Zatvorený Deactivated when triggered Deaktivován pro všechny režimy alarmu Deaktivovaný pre všetky režimy alarmuZavřený

Instant Okamžitý Okamžitý Activated when ARM/HOME ARM Aktivní když je režim alarmu Aktivován/

Režim Doma

Aktívny keď je režim alarmu Aktivovaný /

Režim Doma

24 Hours 24 Hodin 24 Hodín Activated even when DISARM Aktivní vždy i při režimu alarmu Deaktivace Aktívna vždy aj pri režime alarmu

Deaktivácia

Home Režim Doma Režim Doma Deactivated when DISARM/HOME ARM Neaktivní pokud je režim alarmu Deaktivace/

Režim Doma

Neaktívne ak je režim alarmu Deaktivácia /

Režim Doma

Door Chime Uvítací Gong Uvítací Gong No alarm but clanking Bez alarmu, ale uvítací gong (např. pro

obchody)

Bez alarmu, ale uvítací gong (napr. pre

obchody)

Delay Zpoždění Oneskorenie Wait few seconds before alarm Čeká několik vteřin před aktivací alarmu Čaká niekoľko sekúnd pred aktiváciou

alarmu

①Press down the hook on sensor with thumb, push it to open the cover.

①Stiskněte tlačítko dolů pomocí palce a druhou rukou otevřete kryt detektoru.

①Stlačte tlačidlo nadol pomocou palca a druhou rukou otvorte kryt detektora.

②Replace with 2x AA battery.

②Vyměňte 2x AA baterie.

②Vymeňte 2x AA batérie.

Operating Instructions

Installation & Notice

1. Working principle

with digital dual-core fuzzy logic operative pro-

gramming and intelligent analysis, it accurately

detects human body movement with infrared

sensor and sends signal to main panel.

2. Pairing with main panel by App

① Scan the QR code printed on the sensor.

② The pairing result would be confirmed by SMS

sent from main panel.

• Open the case and remove the battery insulative strip.

• Pairing with main panel by App before installing.

• Fix the bracket with double-side sticky tape or screws on wall, connect the sensor to bracket, adjust a

proper angle. 360° angle adjustment is easily available with connection of bead and magnetic slice.

• Recommended to install at height of 1.8-2.2m from ground, with gradient 10°~20°.

• Indoor use only. Avoid installing the sensors in area with strong light, temperature changes rapidly or

the air stream flows frequently, like close to windows, air conditioner, refrigerator, heater, oven, and

large obstacles.

• Aovid installing two sensors in the same detection scope to interference.

• The sensor is more sensitive to the cross movement than to the vertical movement, so the perference

of sensor is best when the detection direction is vertical to the walking direction of people.

PCB Layout

Detective Interval Time

Setting Switch

(every 5s. or 5min.)

On/Off Switch

Infrared Sensor

10°-20°

1.8-2.2m

Detection blind zone

12m6m1.2m

Features

Parameters

Appearance

The M3P1 wireless motion sensor is an accessory of iGET SECURITY M3 series smart alarm system, mainly for indoor use. With

high performance infrared sensor, works under digital dual-core fuzzy logic operative programming and intelligent analysis,

it accurately detects human body movement and effectively avoids false alarms. Featured with automatic temperature

compensation technology, it ensures high intelligence, sensitivity, and stability. It’s fashion design, energy saving, low battery

warning supported and with long transmission distance. The main panel will send a SMS to user for battery changing when

needed. With 360º angle adjustment supported, it’s easy to setup and never get stuck.

• Working Voltage DC 3V

• Battery 2 × AA battery(1.5V)

• Working Current 22mA

• Standby Current 60μA

• Detective Range 110°

• Detective Distance 9m

• Transmission Distance Without obstacle 100m

• Transmission Frequency 433.29MHz

• Working Temperature -10℃~40℃

• Humidity ≤90%rh (non-condensing)

• Weight 66g (battery not included) 112g (battery included) 62.3g (Bracket)

• Dimension 99.6mm*54.0mm*40.2mm L*W*H(±0.1mm)

Detection Window

Magnetic Slice

Trigger Button

Stainless-steel Bead

LED IndicatorBracket

SECURITY M3P1

Exclusive importer of products Shenzhen Dinsafe Intelligence Co., Ltd.

for the Czech Republic and Slovak Republic

INTELEK spol. s.r.o., Vlárská 22, 627 00 Brno

SUPPORT: http: //www.iget.eu/helpdesk

Produkt Specifikationer

Mærke:	Iget
Kategori:	Bevægelsesdetektor
Model:	SMART Security M3P1

Har du brug for hjælp?

Hvis du har brug for hjælp til Iget SMART Security M3P1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bevægelsesdetektor Iget Manualer

Iget SMART Security M3P1 Manual

25 August 2024

Iget SMART Security M3P10 Manual

25 August 2024

Iget SMART Security M3P4 Manual

25 August 2024

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

Theben theLuxa E180 Manual

20 December 2025

Theben TheLeda P24 WH Manual

18 December 2025

ORNO OR-CR-285 Manual

16 December 2025

Heath Zenith 4170 Manual

11 December 2025

Heath Zenith 5846 Manual

10 December 2025

Heath Zenith 4305 Manual

10 December 2025

Heath Zenith 7163 Manual

9 December 2025

Heath Zenith 7161 Manual

9 December 2025

MDT SCN-P360R306.01 Manual

8 December 2025

MDT PSE-PMC06.01S Manual

7 December 2025