Indesit IDC 8T3 B S (UK) Manual

Indesit Tørretumbler IDC 8T3 B S (UK)

Læs gratis den danske manual til Indesit IDC 8T3 B S (UK) (4 sider) i kategorien Tørretumbler. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Indesit IDC 8T3 B S (UK), eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Instruction booklet

TUMBLE DRYER IDC 8T3 B (UK)

IDC 8T3 B K (UK)

IDC 8T3 B S (UK)

Step 1

Open the door of your dryer.

Step 2

Pull out the ﬁ lter (using the two

ﬁ nger grips).

Step 3

Clean the ﬂ uff off the ﬁ lter and

replace it correctly.

Step 4

Make sure the ﬁ lter is pushed fully home -

NEVER run the dryer without the ﬁ lter in position.

Failure to clean the ﬁ lter after EVERY drying

cycle will affect the drying performance of your

machine.

It will take longer to dry and as a result will use

more electricity during drying.

Step 1

Open the condenser cover.

Step 2

Remove the condenser by turning

the 3 catches and

pulling the condenser

towards you. It is normal for some

residual water to be left in the

condenser unit.

Step 3

Flush the condenser

from the rear with water to remove

any ﬂ uff deposits.

Step 4

Replace the condenser unit and

make sure that all 3 catches are

closed and that the position arrows

on the front of the condenser are

pointing upwards.

Less than 1m

This symbol reminds you to read this booklet

WHERE TO INSTALL THE TUMBLE DRYER

Install the dryer far from

gas ranges, stoves, radiators

or hobs as ﬂ ames may

damage it. If the dryer is

installed below a worktop,

ensure there are 10 mm

between the upper panel of

the dryer and any objects

above it and 15 mm between

the sides of the machine

and the walls or furniture units adjacent to it. This

ensures adequate air circulation.The appliance

must be installed with the rear surface placed

against a wall.

! We do not recommend that the dryer is installed

in a cupboard but the dryer must never be

installed behind a lockable door, a sliding door or

a door with a hinge on the opposite side to that of

the dryer door.

Priming the Water Collection System.

When your dryer is new, the water container will not collect water

until the system is primed. This will take 1 or 2 drying cycles. Once

primed it will collect water during every drying cycle.

WATER DRAINAGE CONNECTION

If the dryer is installed next to a drain the

water can be plumbed into this drain. This

does away with the need to empty the

water container. The height of the drain

must be less than 1m from the bottom of

the dryer. Remove the existing hose from

the dryer and connect it to the drain (if

required add an additional length of hose).

ELECTRICAL CONNECTIONS

The socket must be grounded.

! The power cord must be regularly checked. If

the supply cord is damaged it must be replaced

by the manufacturer, its service agent or similarly

qualiﬁ ed persons in order to avoid a hazard.

BEFORE YOU START USING YOUR DRYER

Once you have installed your dryer and before

you use it clean the inside of the drum to remove

any dust that could have accumulated during

transport.

CONDENSER UNIT

You MUST clean the ﬂ uff from the condenser

EVERY month. Failure to clean the condenser

could cause premature failure of your dryer.

Remove the condenser unit regularly (at least

monthly) and clean off any ﬂ uff deposits.

10 mm

15 mm 15 mm

WATER CONTAINER

You empty the water container after MUST EVERY

drying cycle. Removing the water container:

Step 1 Pull the water container

towards you and remove it

completely from the dryer.

Step 2 Empty all the water in the

water container.

Step 3 Replace the water

container making sure that it is securely ﬁ xed.

! Failure to empty the water container will

cause the machine to stop heating and the

load may still be wet at the end of the drying

cycle. The ‘Empty Water’ light will tell you

that the water container needs to be emptied

FLUFF FILTER

You must clean the ﬂ uff ﬁ lter after EVERY drying cycle.

Produkt Specifikationer

Mærke:	Indesit
Kategori:	Tørretumbler
Model:	IDC 8T3 B S (UK)
Vekselstrømsindgangsspænding:	220 - 240 V
Vekselstrømsindgangsfrekvens:	50 Hz
Bredde:	595 mm
Dybde:	610 mm
Højde:	850 mm
Vægt:	35200 g
Produktfarve:	Sølv
Kontroltype:	Buttons, Rotary
Indbygget skærm:	Ingen
Ledningslængde:	1.5 m
Pakkevægt:	36600 g
Pakkedybde:	670 mm
Pakkebredde:	640 mm
Pakkehøjde:	890 mm
Årligt energiforbrug:	560 kWh
Strømforbrug (slukket):	0 W
Placering af apparat:	Fritstående
Tilsluttet belastning:	2400 W
Støjniveau:	68 dB
Ilægningstype:	Front-læsning
Tromlekapacitet:	8 kg
Forsinket start-timer:	Ingen
Børnesikring:	Ingen
Tromle volumen:	112 L
Cyklustid:	147 min.
Tørringsklasse:	C
Energieffektivitetsskala:	A+++ til D
Filterrengøringsindikator:	Ja
Energieffektivitetsklasse:	B
Tørreprogrammer:	Cotton, Synthetics
Tørresystem:	Kondensering
Antal tørreprogrammer:	16
Anti-krølle funktion:	Ingen
Tromle indvendigt lys:	Ja
Nominel strømstyrke:	13 A
Energiforbrug:	4.79 kWh
Varmekilde:	Elektrisk