Intelix AVO-A2 Manual

Intelix AV forlænger AVO-A2

Læs gratis den danske manual til Intelix AVO-A2 (2 sider) i kategorien AV forlænger. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Intelix AVO-A2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Specifications subject to change without notice.
Maximum Distance* 2500 feet
Bandwidth 20 Hz to 20 kHz
Impedance 600 ohms, balanced
Isolation 500 V
Nominal Level 1.0 volts
Insertion Loss 1 dB
Common Mode Rejection Greater than 40 dB
Unshielded Twisted Pair Maximum capacitance: 20 pf/foot
Cabling Specifications Impedance: 100 ohms @ 1 MHz
(24 gauge or lower solid Attenuation: 6.6 dB/1000 ft. @ 1 MHz
copper) Cat 3, Cat 5, Cat 5e, Cat 6, Cat 7 compatible
Connectors Two (2) female RCA to one (1) RJ45
RJ45 Pinout Channel 1 (R): 1 & 2, pair 2
Channel 2 (L): 3 & 6, pair 3
Temperature Operating: 32 to 131 F (0 to 55 C)
Storage: -4 to 185 F (-20 to 85 C)
Humidity: up to 95%
Enclosure Black plastic
Dimensions 4.3” x 2.5” x 1”
Weight 0.2 lbs (3.2 oz.)
Ordering Information AVO-A2: single AVO-A2 balun in bulk packaging
AVO-A2-PAC: two AV0-A2 baluns in retail-ready packaging
Warranty 2 years
*Distances and picture quality may be affected by cable grade, cable quality, source and
destination equipment, RF and electrical interference, and cable patches. Intelix specifications are
based on straight-through cabling with standard-grade Cat 5.
Intelix
2222 Pleasant View Road
Middleton, WI 53562
Toll-free: 866-4-MATMIX
Phone: 608-831-0880
Fax: 608-831-1833
www.intelix.com
Intelix AVO-A2 Stereo Audio Balun
The Intelix AVO-A2 balun passively transmits two
mono or one stereo analog audio signal via Cat 5
unshielded twisted pair (UTP) cable, such as Cat 5.
Used in pairs, the AVO-A2 transmits analog audio in
either direction up to 2500 feet, providing a low-cost,
versatile cabling solution which uses a building’s
existing structured cabling system
The AVO-A2 is ideal for corporate AV, houses of
worship, schools, auditoriums, and virtually any other
situation involving structured audio distribution
To install an AVO-A2 balun, perform the following steps:
1. Turn off power and disconnect the audio equipment by following the manufacturer’s
instructions.
2. Make certain that outlets and cross connects to which you will connect the AVO-A2
are configured properly and labeled appropriately to identify the circuit.
3. Verify the desired twisted pairs are not being used for other LAN or telephony
equipment.
4. Connect the RCA inputs from the source equipment to one of the two baluns. Two
AVO-A2’s are needed—one at each end of the run—and are interchangeable.
5. Connect a 4-pair Cat 5 cable from the RJ45 8-position modular jack of the AVO-A2
to a structured cable, such as Cat 5.
6. Connect the second balun’s RCA inputs to the destination equipment.
7. Connect the 4-pair Cat 5 cable from the RJ45 8-position modular jack of another
AVO-A2 to the structured cable attached to the first balun.
8. Power on the source and destination equipment and test for correct operation.
Caution: Do not attempt to open the balun housing. There are no user-serviceable parts
inside the AVO-A2. Opening the unit will void your warranty.
Caution: Do not connect the AVO-A2 to a telecommunication outlet wired to unrelated
equipment. Making such a connection may damage the equipment and/or
balun. Please ensure all wiring is “straight-through.”
Caution: Do not mount the balun over equipment ventilation openings. Covering the
openings may cause the equipment to overheat.
Cat
Series
If your equipment malfunctions with AVO-A2 baluns in place, follow the troubleshooting
procedures below:
1. Perform diagnostics on your audio equipment by following the manufacturer’s
instructions.
2. Check all the connections and the structured cabling system. Verify the RJ45 crimp
pattern conforms to either EIA/TIA 568A or 568B standards.
3. Check the pin configuration on the structured cable.
4. The maximum operational distances over which the AVO-A2 can be transmitted is
dependant on the equipment used and cable. Ensure that the maximum recommended
operational distances have not been exceeded.
5. Check that only twisted pair patch cords are being used.
6. Replace the AVO-A2 balun with another AVO-A2 that is known to be working.
7. If you still cannot diagnose the problem, contact Intelix for support.
How do I expose the individual pairs in Cat 5 cabling?
There is no single method when exposing the four
individual pairs in twisted pair cabling, such as Cat 5
and Cat 6; however, it does help to have a cable
stripping tool designed to strip the cable jacket/
insulation.
Begin by stripping back the cable’s outer jacket/
insulation about an inch (or more depending on
whether multiple baluns will be connected to the pairs
of a single cable) so that the internal wires are exposed.
Be careful not to cut the internal wires when stripping
the insulation/jacket. Eight twisted wires and a string
should now be visible; the string is unnecessary and
may be removed. These eight wires, which when
combined form four pairs, connect directly to the
baluns. Typical protocol pairs similar colors; the
important thing is to verify the same color-coded pairs
are used on each end.
How do I crimp an unshielded RJ45 connector onto Cat 5?
Crimping an RJ45 connector onto Cat 5 is a fairly straight forward task, assuming you have
the proper tools. Keep in mind that baluns require either the EIA/TIA 568A or 568B crimp
pattern, which are the industry standards for networking.
1. First, strip a portion of the insulation about 3/4" to expose the four twisted pairs.
2. Next, untwist the wires and fan them out so that they match either EIA/TIA 568A or
568B pattern.
3. Evenly trim the wires to about 1/2". Most RJ45 crimp tools feature a built-in wire
trimmer.
4. Insert the trimmed wires into the RJ45 connector so that each wire is in its individual
slot. Verify each wire is completely inserted.
5. Finally, insert the RJ45 connector into the crimp tool and squeeze firmly.
6. Repeat the above steps on the other end of the Cat 5 cable and verify pinout is iden-
tical on each end.

Produkt Specifikationer

Mærke: Intelix
Kategori: AV forlænger
Model: AVO-A2

Har du brug for hjælp?

Hvis du har brug for hjælp til Intelix AVO-A2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


AV forlænger Intelix Manualer

Intelix

Intelix AVO-A2 Manual

8 Juni 2024

AV forlænger Manualer

Nyeste AV forlænger Manualer

Kramer

Kramer 690R Manual

1 August 2025
Tripp Lite

Tripp Lite B132-100-1 Manual

31 Juli 2025
Tripp Lite

Tripp Lite B126-1A1SR Manual

31 Juli 2025
Tripp Lite

Tripp Lite B127U-002-PDPD2 Manual

31 Juli 2025
Tripp Lite

Tripp Lite B140-004 Manual

31 Juli 2025
Tripp Lite

Tripp Lite B127U-002-PHPH2 Manual

31 Juli 2025
Tripp Lite

Tripp Lite B126-2A0 Manual

31 Juli 2025
Tripp Lite

Tripp Lite B126-1A1-PLHD Manual

31 Juli 2025
Tripp Lite

Tripp Lite B013-330 Manual

31 Juli 2025
Tripp Lite

Tripp Lite B127U-111-PHPH Manual

30 Juli 2025