Intermatic EH10 Manual

Intermatic Tidsskifte EH10

Læs gratis den danske manual til Intermatic EH10 (8 sider) i kategorien Tidsskifte. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Intermatic EH10, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

ELECTRONIC 7-DAY WATER -

HEATER TIME SWITCHES

MODELS EH10 AND EH40

WITH BATTERY CARRYOVER

MAN

AUTO

PROG

RUN

TIME

SET

OFF

EVENT DAY HOUR MINLOAD

RESET

BATTERY

OWNER/INSTALLER INSTRUCTION MANUAL

ATTENTION: READ CAREFULLY BEFORE ATTEMPTING

TO INSTALL YOUR INTERMATIC TIME SWITCH. FAIL-

URE TO COMPLY WITH INSTRUCTIONS COULD

RESULT IN PERSONAL INJURY AND/OR PROPERTY

DAMAGE! RETAIN FOR FUTURE REFERENCE.

MANUAL (MAN) - AUTOMATIC (AUTO)

(See Fig. 1)

•MANUAL: Bypasses your program completely; timer

will not resume program until you return switch to

AUTO mode position.

•AUTOMATIC: For automatically switching at ON/OFF

times; accurate to-the-minute.

PROGRAM (PROG) - RUN - TIME SET

•PROGRAM: Use this position when programming.

•RUN: Use this position for normal operation. Be sure to

return to RUN after setting time and program.

•TIME SET: Use this position to set day and time of day.

ON/OFF - EVENT (the large push button) - Serves a dual

purpose

• EVENT: Used for programming (active only when switch

is set at PROG)

• ON/OFF: Override (active only when switch is set at

RUN); turns load ON if already off or OFF if already on.

Timer automatically resumes program cycle only when

slide switch is in AUTO. Note that this button is also

accessible without opening the enclosure.

SPECIFICATIONS:

Clock Voltage - Model EH40 - 240V. A.C., 50/60 Hz

EH10 - 120V. A.C., 50/60 Hz

Power Consumption - EH10 - 1.0 W. Max. EH40 - 3.0

W. Max..

Contact Configuration - EH10 (SPST) Single pole-single

throw model-EH40(DPST) Double pole-single throw model

Switch Rating (Per Pole) -

• 30 amp inductive/resistive - 120-240V. A.C., 60 Hz

• 1 H.P. 120V. A.C., 60 Hz.

• 1-1/2 H.P. 240V. A.C., 60 Hz.

• 5 amp tungsten, 120-240V. A.C., 60 Hz.

Set Points (Events) - 12 total (6 ON/6 OFF) - Can be

assigned in any combination to weekdays, weekend days,

daily or weekly operation providing up to a maximum of 84

weekly operations (42 ON/42 OFF).

Battery Powered Clock Operation - 3 years minimum,

AA industrial grade alkaline supplied with time switch.

Minimum ON/OFF Time - 1 Minute

Maximum ON/OFF Time - 6 days 23 hours 59 minutes

Shipping Weight - 2.37 Lbs. (1.05 Kg)

Case - Drawn steel, 7-3/4” (19.7 cm) high, 5” (12.7cm)

wide, 3” (7.6 cm) deep; gray finish with lockable spring

hasp, clear see-through viewing window and external over-

ride.

Knockouts - Combination of 1/2 - 3/4” (one on back and

each side, two on bottom)

Wire Size - AWG #10 through #18

GENERAL SAFETY INFORMATION:

WARNING: DISCONNECT THE POWER TO THE TIME

SWITCH AND THE LOADS BEFORE INSTALLING THIS

TIME SWITCH.

1. Mount the time switch in the desired location using the

three mounting holes which are provided. Mount the

time switch at eye level, if possible, providing

sufficient room to the left of the enclosure for the

cover to swing open fully. (See Fig. #2). The time switch

mechanism does not need to be removed from the

enclosure to mount the time switch since the top mount-

ing hole is a slotted type mounting hole. Secure a screw

or other fastener at eye level. The head of the screw

of fastener should be slightly larger than the narrow

portion of the slotted hole to ensure that the time switch

is securely held in place. The remaining two mounting

holes provide a means to secure the time switch.

2. If you do remove the mechanism, refer to Figure #3 and

remove the mechanism from the case by depressing

the catch at the top of the case and pulling out.

CAUTION: DO NOT TOUCH THE CIRCUIT

BOARD COMPONENTS SINCE STATIC DISCHARGE

COULD DAMAGE THE MICROPROCESSOR.

3. Replace the mechanism in the case if it has been

removed, making sure to engage ribs at sides of

mechanism between ears at sides of case before

snapping in place.

4. Lift the left side of the insulator off of the retaining post

and pivot it up and away to expose the terminal

screws.

5. Strip the supply and load wires by removing 1/2 inch of

insulation. DO NOT USE ALUMINUM WIRE. Insert

the wire ends under the proper terminal plates and

tighten the screws firmly. Use any size wire,

AWG #10 through #18. Connect ground wire to

grounding terminal at bottom of case.

6. Replace the plastic insulator.

7. Follow instructions for battery installation. Be sure that

the battery is functioning properly. This can be checked

by seeing that the display is visible. If the display

has scrambled information, check to be sure that

the polarity orientation of the battery is as shown on

the cover label, then press the RESET switch and hold

for at least two seconds. Note that the battery can

easily be replaced without removing the time

switch mechanism or field wiring. Simply press in and

downward (in the direction of the arrow) on the

battery cover which is identified with the word “Battery”.

It is recommended that the battery be replaced with a

“AA” industrial grade alkaline cell at two to three

Fig. 3

Fig.2

Fig.1

Mounting Holes

Knockouts

Ground

Terminal

Snap Out Catch Tilt Top Forward

Lift Up

Remove

hp://waterheatermer.org/How- -wire-EH40-hot-water-heater-mer.htmlto

________________________________________________________________

year intervals as part of the normal time switch

maintenance observing battery polarity markings when

installing. No other maintenance is required.

8. Place the slide switches in the AUTO and RUN position.

9. Reapply power to the time switch.

10. Press the recessed reset switch for at least two

seconds. The display will show 12:00 A.M. and MO.

Note that the days of the week are identified with the

first two letters of the day (MO for Monday).

The timer is now ready for programming. Refer to the

examples which follow and enter the scheduled events

(set points) required. Assign each of the 12 set

points (EVENTS) entered to whichever day or groups

of days of the week you wish an ON or OFF

operation to occur.

Set Point = Event = ON = OFF

PROGRAMMING STEPS:

SET CURRENT DAY AND TIME

Slide switch to TIME SET. Push DAY until current day

shows, then push HOUR until current hour AM or PM

shows. Now push MINUTE until current minute

shows. Clock is now set. Follow same procedure after

replacing battery or changing time (such as

for daylight saving time).

SET YOUR PROGRAM

Slide switch to PROG. Display will look like this: (-:- -)

•Press DAY until desired program period shows (see

choices in “PROGRAM PERIOD OPTIONS” section

above).

•Press HOUR until desired “ON 1” hour shows (that

is, the first time each day of the program period that

you want the load to turn ON).

•Press MINUTE until desired minute shows.

•Press EVENT to program time for ON 1 (and to

advance to programming for OFF 1).

•Press DAY again until all seven days of the week

show (or until another desired program period

option shows; see “PROGRAM PERIOD

OPTIONS”).

•Press HOUR again until desired “OFF 1” hour shows

(that is, the first time each day of the program

period that you want the devices to turn OFF).

•Press MINUTE until desired minute shows.

•Press EVENT to set time for OFF 1. You may now

begin setting ON 2, a second ON time, for the same

program period, OR press DAY to change to a

different program period.

•Repeat above procedure until all desired ON/OFF

programs are set.

PLEASE NOTE: Before you program your timer, or when you

remove the battery, or when you use the RESET, pressing

EVENT will display the bar symbol -:-- ON 1. Repeated press-

ing of EVENT will display all the way through the final bar sym-

bol -:-- OFF 6. Once you program your timer, however, each

actual time setting you make will replace the bar symbol. While

programming, each time you press you will advance toEVENT

the next EVENT.

PROGRAM PERIOD OPTIONS:

Your timer gives you up to 6 different ON and 6 different OFF

settings per program period. You can use all 6 settings per peri-

od, or as few as you like. A program period covers one of these:

•ALL 7 DAYS OF THE WEEK combined into one -

display shows: MO TU WE TH FR SA SU.

•MONDAY THRU FRIDAY combined into one -

display shows: MO TU WE TH FR.

•SATURDAY AND SUNDAY combined into one -

display shows: SA SU

•EACH INDIVIDUAL DAY OF THE WEEK -

display shows only that day.

•BLANKDAY EXPLANATION - “BLANKDAY”

follows Sunday after last push of DAY button (when

the lower slide switch is set at PROGRAM). The

purpose of the BLANKDAY is to disable a program

setting on a day.

Program periods with days “combined into one” help you

make settings for those multiple days quickly and conve-

niently while using only one ON/OFF pair. When you set

such a program period, all settings will be identical for

every day of that period.

PERSONAL PROGRAM EXAMPLES

EVENTS

DAY CHECKS ON TIMES OFF TIMES DISPLAYED DAYS & TIMES DISPLAYED

EXAMPLE 1

MO TU WE TH FR SA SU 5:00 PM 10:00 PM ON 1 MO TU WE TH FR SA SU 5:00 PM

OFF 1

EXAMPLE 2

MO TU WE TH FR 6:00 PM 10:00 PM ON 1 MO TU WE TH FR 6:00 PM

OFF 1 MO TU WE TH FR

10:00 PM

SA SU 4:00 PM 8:00 PM ON 2 SA SU 4:00 PM

OFF 2 SA SU 8:00 PM

EXAMPLE 3

MO TU WE TH FR 6:00 AM 9:30 AM ON 1 MO TU WE TH FR 6:00 AM

OFF 1 MO TU WE TH FR 9:30 AM

MO TU WE TH FR 5:30 PM 11:15 PM ON 2 MO TU WE TH FR 5:30 PM

OFF 2 MO TU WE TH FR 11:15 PM

SA SU 3:00 PM 10:00 PM ON 3 SA SU 3:00 PM

OFF 3 SA SU 10:00 PM

EXAMPLE 4

MO TU WE TH 8:00 PM 11:30 PM ON 1 MO TU WE TH 8:00 PM

OFF 1 MO TU WE TH 11:30 PM

FR SA 5:00 PM 2:20 PM ON 2 SU 7:00 PM

(DAY AFTER) OFF 2 SU 10:30 PM

SU 7:00 PM 10:30 PM ON 3 FR 5:00 PM

OFF 3 MO 11:30 PM

ON 4 SA 5:00 PM

OFF 4 TU 11:30 PM

ON 5 “BLANKDAY” -:- -

OFF 5 WE 11:30 PM

ON 6 “BLANKDAY” -:- -

OFF 6 TH 11:30 PM

NOTE: “-:- -” follows Sunday after last push of DAY button

(when the slide switch is set at PROG). The purpose of the

-:- - is to cancel a program setting on that day.

REVIEW YOUR PROGRAM

Slide switch to PROG. Press EVENT button to advance

display to each ON or OFF setting. Check days and times

displayed. To make a change, follow instructions under

“SET YOUR PROGRAM”. To delete a displayed set point,

press DAY button until “-:- -” is displayed.

GENERAL FEATURES AND HINTS FOR TROUBLE-

FREE USE

•BUTTON: When you press a button, there is an advance

of one time unit; holding a button down advances contin-

uously until released.

•MAINTENANCE: With the exception of battery replace-

ment at 2-3 year intervals, your Intermatic timer is

maintenance-free.

•AFTER THE INSTALLATION IS COMPLETED, THE

LOCKABLE HASP SHOULD BE MOVED TO THE UP

POSITION TO ENGAGE THE COVER WHEN IT IS

CLOSED.

FULL ONE YEAR WARRANTY

If within one (1) year from the date of purchase, this product fails

due to a defect in material or workmanship, Intermatic

Incorporated will repair or replace it free of charge. The warranty

does not apply to (a) damage caused by accident, abuse, mis-

handling or dropping: (b) units which have been subject to unau-

thorized repair, opened, taken apart; (c) units not used in accor-

dance with directions; (d) damages exceeding the cost of the

product. Some states do not allow a limitation of damages, so the

foregoing limitation may not apply to you. This warranty gives you

specific legal rights, and you may also have other rights which

vary from state to state.

This warranty service is available by either (a) returning the prod-

uct to the dealer from whom the unit was purchased, or (b) mail-

ing postage prepaid to the authorized service station listed below.

Please be sure to wrap the product securely when mailing to

avoid damage. This warranty is made by: Intermatic Incorporated,

Intermatic Plaza, Spring Grove, Illinois 60081-9698.

AUTHORIZED SERVICE STATION

INTERMATIC INCORPORATED

4720 West Montrose Avenue

Chicago, Illinois 60641

INTERMATIC INCORPORATED

SPRING GROVE, ILLINOIS 60081-9698

158ET8805 PRINTED IN U.S.A.

TIMER

POWER

LOAD

NEUTRAL

1 2 3 4

Fig. 4 Fig. 5

TIMER

POWER

1 2 3 4 5 6

LINE 1

LINE

LINE 2

LINE 1 LINE 2

LOAD

120 ≈

240≈

EH10

EH40

- 2 -

See

Pg. 7

See

Pg. 7

Produkt Specifikationer

Mærke:	Intermatic
Kategori:	Tidsskifte
Model:	EH10

Har du brug for hjælp?

Hvis du har brug for hjælp til Intermatic EH10 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Tidsskifte Intermatic Manualer

Intermatic ST01 Series Manual

15 Januar 2025

Intermatic EH10 Manual

6 Juli 2024

Intermatic WH21 Manual

6 Juli 2024

Intermatic EH40 Manual

4 Juli 2024

Tidsskifte Manualer

Nyeste Tidsskifte Manualer

SilverCrest Digitale tijdschakelaar Manual

15 Januar 2025

Selecttime 1728391 Manual

14 Januar 2025

Profile PCF-360 Manual

23 September 2024

Profile 840000020 Manual

17 September 2024

Sygonix 1625525 Manual

27 August 2024

Sygonix 1528595 Manual

27 August 2024

TimeControl AX-801 Manual

26 August 2024

TimeControl DX-2 Manual

26 August 2024

TimeControl 2000 Electronic Manual

26 August 2024

Wachsmuth - Krogmann WK140A Manual

26 August 2024