Irritrol 2507DK-LF Manual


Læs gratis den danske manual til Irritrol 2507DK-LF (7 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Irritrol 2507DK-LF, eller vil du spørge andre brugere om produktet?

Side 1/7
®
Drip Zone Valve Kits
Installation Instructions
Click on the links to view the documents.
Drip Zone Valve Kit
Models 2500DK-1-LF and 2500DK-1-MF
Installation Instructions
373-0512 Revision B
Drip Zone Valve Kit
Models 2711APRDK-LF and 2711APRDK-MF
Installation Instructions
373-0513 Revision B
Drip Zone Valve Kit
Models 2713APRDK-LF and 2713APRDK-MF
Installation Instructions
373-0514 Revision B
Drip Zone Valve Kit
Models 700DK-075-LF
Installation Instructions
373-0515 Revision B
Drip Zone Valve Kit
Models 700DK-1-LF and 700DK-1-MF
Installation Instructions
373-0516 Revision B
Drip Zone Kit - Less Valve
Models DK-LV-LF and DK-LV-MF
Installation Instructions
373-0535 Revision A
®
Get more doneTM
Drip Zone Valve Kit
Models 2500DK-1-LF and 2500DK-1-MF
Installation Instructions
Kit Components
• Irritrol 2500 Series Valve, Model 2500TF
• Pressure Regulator - 25 psi at 0.1–8 GPM,
3/4" Female NPT (Low Flow [LF] model)
• Pressure Regulator - 25 psi at 2–20 GPM,
3/4" Female NPT (Medium Flow [MF] model)
• 3/4" MPT x MPT F Series Y-filter, 150 Mesh Screen
• Drip Line Compression Adapter, CA-710
• 1" x 3/4" Male NPT Reducer Bushing
• 3/4" MPT x 1/2" Slip Fitting
Specifications
• Downstream Pressure Regulation: 25 psi
• Flow Rate at 25 psi: (LF Model) 0.1–8 GPM
(MF Model) 2–20 GPM
• Filtration: 150 Mesh Stainless Steel Screen
• 1" In-line Electric Control Valve, Model 2500TF
Operating Pressure: 10–150 psis
24 VAC, 50/60 Hz Solenoids
Inrush: 0.40 amp, 9.6 VA s
Holding: 0.20 amp, 4.8 VA s
Manual On/Off - Internal and External Bleeds
Adjustable Flow Controls
Installation Procedure
CAUTION: When assembling the drip zone valve kit components, use just 1 ½ to 2 turns of PTFE tape on male
threads. Never use pipe dope. To achieve a leak-free thread connection, turn the male fitting until it is finger-
tight, and then add one or two more turns. Over-tightening can cause splitting and failure of the female threads.
Important: Ensure the Y-filter, control valve and pressure regulator are installed in the correct flow
orientation. Flow direction arrows are provided on each component. Refer to Figure 1.
1. Thread the Y-filter inlet into the valve outlet with
the provided 1" x 3/4" NPT reducer bushing. Use
PTFE tape on all threaded connections. Angle the
Y-filter slightly downward as shown in Figure 1.
2. Thread the pressure regulator inlet into the Y-filter
outlet.
3. Connect the water source supply line and piping
to drip emitters.
NOTE: Installing the valve assembly below grade
in a valve box is recommended for protection and
ease of service.
NOTE: Refer to the 2500TF Series Valve
Instruction Guide provided in the kit for complete
valve installation and operation information.
NOTE: To adapt the Drip Zone Valve Kit for
dripline applications, install the provided 3/4" MPT
x 1/2" Slip fitting and CA-710 dripline compression
adapter to the pressure regulator outlet.
4. Flush the system to remove debris.
5. To determine the recommended minimum/
maximum number of drip emitters per control
valve, refer to the table below.
2500TF Series Valve
Valve Box
Reducer
Bushing
Y-filter
Pressure
Regulator
3/4" MPT x
1/2" Slip
Compression Adapter
(Use with Flex Tube only)
To Emitters From Source
Figure 1
Table 1
© Irritrol • www.irritrol.com • For Technical Assistance, call 1-800-333-3125 Part Number 373-0512 revision B
Back to Menu


Produkt Specifikationer

Mærke: Irritrol
Kategori: Ikke kategoriseret
Model: 2507DK-LF

Har du brug for hjælp?

Hvis du har brug for hjælp til Irritrol 2507DK-LF stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Irritrol Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer