James 540SAS-4 Manual

James Subwoofer 540SAS-4

Læs gratis den danske manual til James 540SAS-4 (2 sider) i kategorien Subwoofer. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om James 540SAS-4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Attach the brackets to the speaker using the

supplied 8/32 screws lock washers & at washers .

CD E

PAGE 4 PAGE 1

20190308

2185 Park Place, Minden, Nevada 89423 • Phone: 707.265.6343 | Fax: 707.265.6334 • www.jamesloudspeaker.com

Installation guide for the 101SA-6/540SAS-4 In-Ceiling Small Aperture

® Speaker

101SA-6/540SAS-4

1) #2 Phillips screwdriver

or drill with #2 Phillips

drill bit

2) Straight edge or level

3) Wood or drywall screws

The brackets (Part No.

SA-BRKT-11-22) are

designed for 16” On-center

constructions, however can

be adjusted to accommodate

construction from 11” to

22.5” joist spacing (Fig. 1).

Tools Required:

Assemble the parts

1 - 101SA-6 or 540SAS-4

2 - Mounting Brackets

4 - 8-32 x 1/2 Pan Head

Machine Screws

4 - #8 Lock Washers

4 - #8 Flat Washers

4 - 6/32 Course Head Screws

1 - Foam Dust Guard

Parts List: Supplied

4 - 1.25” Wood or drywall

screws

Parts List: Supplied by Installer

1 - Trim Kit

Spacer Ring(s)

Parts: Ordered Separately

Tighten these screws just enough to allow

movement for adjustment during installation.

Note: brackets can be mounted to either the sides

of the ends of the speaker enclosure for added

installation ﬂexibility.

P/N SA101-SP-0.125

Attach the nishing trim kit

Recommend testing sub with program material

to assure sub reaches its intended frequency

range and that all components are working.

Attach spacers if required

Install foam dust guard.

Drywall, tape, mud, etc.

Safely store the supplied grille for the nal

assembly.

Fig. 1

13”

25.5”

Fig. 15 There are four trim kits

avilable to choose from

Fig. 16

Fig. 17

Fig. 18

Fig. 20

SA101-4S-SRSA101-5R-SR SA101-4S-WSA101-5R-W

For 1/2” Drywall omit spacer (Fig. 17)

For 5/8” Drywall use spacer (Fig. 18)

If the drywall is in excess of 5/8”

add additional 1/8” spacers as needed

Small Aperture

Installation

Video

Trim Kit

Finishing

Playlist

Products suitable for use in

dry outdoor environments

101SA 540SAS-4

Freq. Response 33-150Hz 38-150Hz

Impedance 8 ohm 8 ohm

Sensitivity 87dB 89dB

Amp Range 100-350 Watts 75-250 Watts

PAGE 3PAGE 2

Installation guide for the 101SA-6/540SAS-4 In-Ceiling Small Aperture

® Speaker

101SA-6/540SAS-4

Mount temporary holders to joists

Firmly secure the bracket to the speaker

Remove the temporary holders from the joists

Double check that the face of the speaker

is plumb with joist

Strip an insert wires into terminals

Place the speaker on top of the temporary holders

Fix the brackets to the joists

Cut a couple of 2 x 4s or 1 x 2s, a few

inches wider than the ceiling joists.

Then with a couple of drywall screws,

mount the temporary holders to the

joists. (Drywall screws not included).

Note: 63SA-7 is pictured

in steps 2,8. Procedures

for 101SA-7/540SAS-4 are

identical.

Expand the bracket to ﬁt from joist to joist (Fig. 8). Then ﬁx to the joists using a drywall

screw (Fig. 9). Make certain the bracket is ﬂush with the joists (Fig. 10).

(Drywall screws not included).

Tighten screws enough

to securely ﬁx the bracket

to the speaker enclosure.

Be careful not to strip the

threads on the brackets

(Fig. 11).

You can adjust the side-

to-side position of the

speaker by sliding the

bracket before tightening.

Remove drywall screws and

remove the temporary holders

(Fig. 12a).

Tighten bracket to speaker

with a drill or Allen key, while

being careful not to strip the

threads on the brackets

(Fig. 12b).

Adjust if needed (loosen

the bracket slightly and

adjust the speaker’s

position up or down or as

required (Fig. 13).

Minimum 18-gauge wire,

heavier gauges for longer

wire runs.

Fig. 5

Fig. 11

Fig. 13

Fig. 14

Fig. 8 Fig. 9 Fig. 10

Fig. 6

These will help you hold

the speaker up and make

the speaker mount ﬂush

to the future drywall.

Fig. 7

Fig. 12a

Fig. 12b

Produkt Specifikationer

Mærke:	James
Kategori:	Subwoofer
Model:	540SAS-4
Materiale:	Aluminium
Impedens:	8 ohm (Ω)
Subwoofer RMS-effekt:	250 W
Subwoofer frekvensomrpde:	38 - 150 Hz
Subwoofer, følsomhed:	89 dB
Subwoofer dybde:	86.36 mm
Subwoofer bredde:	355.6 mm
Subwoofer vægt:	18370 g
Subwoofer højde:	914.4 mm