James SPL6QLCR Manual

James Højttaler SPL6QLCR

Læs gratis den danske manual til James SPL6QLCR (2 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 4 anmeldelser. Har du et spørgsmål om James SPL6QLCR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTALLATION GUIDE

Spacers have been provided to elevate

the SPL bracket high enough to clear any

protrusions on the display that my interfere

with the bracket mounting process. We

recommend using the minimal amount of

spacers required to clear any protrusion.

Determine the screw size, M6 or M8,

required to mount your wall bracket to the

display. Select either the M6 or M8

hardware bag. 3 lengths are provided,

35mm, 45mm, and 50mm. Select the

correct length to match the spacer quan-

tity (height) and then loosely mount the

brackets to the rear of the display.

SPL6 UNIVERSAL MOUNTING BRACKET

Installation guide for James Loudspeakers SPL6 SoundBar universal mounting bracket.

BRACKETS SUPPLIED HARDWARE

Part # QTY Screws

#1 28 VESA Spacers (1.25˝ x 0.125˝)

#2 4 M8-50mm Pan Head Philips Screws

4 M8-45mm Pan Head Philips screws

4 M8-35mm Pan Head Philips screws

#3 4 M6-50mm Pan Head Philips Screws

4 M6-45mm Pan Head Philips screws

4 M6-35mm Pan Head Philips screws

#4 4 UNC 1/4-20˝ Pan Head Philips Screws

4 Sealing Washers (0.625˝ x 0.275˝)

2 UNC 10-24 Flat Head

After the bracket has been inserted into the

channel of the SoundBar, slide the bracket

left to right to align them to the VESA

pattern on the rear of the display.

Place the display on a padded ﬂat surface. Loosen screws on bracket and

pre-assembled swivel joints, so that they

can slide/pivot with little resistance.

If extra support is desired on the sliding

portion of the bracket, then use the

additional screws and washers provided.

123Before mounting the bracket to the rear

of the display, ﬁrst insert the bracket into

the channel located on the rear of the

SoundBar.

Part A (Pre-Assembled)

(2) VESA rails, (2) Bracket rails,

(2) Long swivel joints (part B)

Non James TV bracket shown for illustration

- Slide the adjustable portion of the

holding tab into the bottom slot of

the SoundBar.

- Tighten the two screws on each of

the holding plates

James Loudspeaker | 535 Airpark Road, Napa, CA94558 | 707.265.6343 | www.JamesLoudspeaker.com

20180305

SPL6 UNIVERSAL MOUNTING BRACKET

Connect wires to terminals, ensuring

correct polarity, before mounting to wall.

Follow the manufacturer’s instruction

for the wall mount installation.

(Will require 2 or more people).

Make all ﬁnal adjustments to swivel

joints and bracket tabs, make sure to

avoid stressed positions/alignments.

Lastly, tighten all screws on joints & tabs

while applying constant pressure on the

SoundBar so that it’s snug against the

display while tightening fasteners.

If desired, tightening the set screws

located in the bracket’s trusses will make

micro adjustment’s to the SoundBar’s tilt

angle.

Produkt Specifikationer

Mærke:	James
Kategori:	Højttaler
Model:	SPL6QLCR
Dybde:	101.6 mm
Højde:	206.38 mm
Udgangseffekt (RMS):	200 W
Husmateriale:	Aluminium
Anbefalet brug:	Universel
Frekvensområde:	60 - 24000 Hz
Impedens:	4 ohm (Ω)
Diskanthøjttaler:	Ja
Antal drivere til diskant:	12
Sensitivitet:	91 dB
Diskant diameter:	19 mm
Bashøjttaler:	Ja
Woofer diameter:	165 mm