Jamo 883K4 Manual

Jamo Højttaler 883K4

Læs gratis den danske manual til Jamo 883K4 (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Jamo 883K4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

In-Wall speakers

WARNING: Improper installation of the speaker could result in amplifier damage. Read all

instructions before installation.

Placement

Make certain the speaker is located between wall studs to avoid cutting into studs. Place the

supplied template a minimum of 5/8 from any studs. Level it and draw a line around it to mark

the cutout. Take care when cutting the hole to avoid cutting into pipes or electrical conduits. If

you encounter pipes, electrical conduits or other obstacles you may have to select another

location for the speaker.

Installation

First install the frame. Loosen screws A (fig. 1) by turning them counter clockwise. Loosen all 4

screws until the Dog ears B (fig. 2) can move freely. Do not remove the screws. Install the frame

into the wall and level it (notice TWEETER and WOOFER markings on the frame). Turn screws A

clockwise until they are tightened and the frame is firmly installed.

Next install the speaker into the frame. Before installing the speaker connect the speaker wires

as described under Hookup and set the impedance switch to the desired position (see

Adjustments). Remove the grill from the speaker. Place the speaker into the frame and secure

with the 6 screws supplied.

Before reinstalling the grill on the speaker make tweeter level adjustments as described under

Adjustments. Reinstall the grill. If the grill has a loose fit and/or is vibrating when the speaker is

playing remove the grill, install the supplied non-curing glue strips at locations C (fig. 1) and

reinstall the grill.

Hookup

The receiver/amplifier must be turned OFF before you connect the speaker or it may cause dam-

age to the amplifier.

Connect the speaker wires from the receiver/amplifier to the speakers. When connecting the

speaker wires make sure that LEFT (L) is connected to LEFT (L), RIGHT (R) to RIGHT (R), POSITIVE

(+) to POSITIVE (+) and NEGATIVE (-) to NEGATIVE (-). If terminals are color coded, RED is POSI-

TIVE (+) and BLACK is NEGATIVE (-).

Adjustments

The tweeter can be tilted towards the listening area, due to high frequencies being more

directional than low frequencies. The impedance of the speaker and the level of the tweeter are

adjustable.

IMPEDANCE:

Located on the crossover on the back. The factory setting is 8 ohm. If the

receiver/amplifier specifies a minimum impedance of 4 ohm, the speaker

may be switched to the 4 ohm position. This will make the speaker play

louder. When installing more then 1 pair of speakers to a receiver/amplifier

special care should be taken to impedance matching the speakers to the

receiver/amplifier. This may require impedance matching devices. Con-

sult your dealer for information regarding impedance matching.

Produkt Specifikationer

Mærke:	Jamo
Kategori:	Højttaler
Model:	883K4
Type:	I væggen/på væggen/i loftet højttalere
Vægt:	2900 g
Produktfarve:	Hvid
Udgangseffekt (RMS):	90 W
Dimensioner (BxDxH):	241 x 98 x 343 mm
Frekvensområde:	60 - 22000 Hz
Impedens:	4 ohm (Ω)
Lyd-output kanaler:	1.0 kanaler
Fjernbetjent:	Ingen
Diskanthøjttaler:	Ja
Peak Music-Udgangseffekt (PMPO):	180 W
Sensitivitet:	91 dB
Diskant diameter:	25 mm
Woofer diameter:	203 mm
Mid-range driver diameter:	38 mm