JANDY JEP-R Manual

JANDY Pomp JEP-R

Læs gratis den danske manual til JANDY JEP-R (60 sider) i kategorien Pomp. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 20 anmeldelser. Har du et spørgsmål om JANDY JEP-R, eller vil du spørge andre brugere om produktet?

Side 1/60
H0412200 Rev J
ENGLISH | FRAN AIS | ESPAÑOLÇ
WARNING
FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and
qualified in pool equipment by the jurisdiction in which the product will be installed where such state
or local requirements exist. The maintainer must be a professional with sufficient experience in pool
equipment installation and maintenance so that all of the instructions in this manual can be followed
exactly. Before installing this product, read and follow all warning notices and instructions that accompany
this product. Failure to follow warning notices and instructions may result in property damage, personal
injury, or death. Improper installation and/or operation will void the warranty.
Improper installation and/or operation can create unwanted electrical hazard which can
cause serious injury, property damage, or death.
ATTENTION INSTALLER - This manual contains important information about the
installation, operation and safe use of this product. This information should be given to
the owner/operator of this equipment.
INSTALLATION AND
OPERATION MANUAL
Jandy Pro Series
JEP-R
Variable-Speed Pump Digital Controller
For use with Jandy Pro Series Variable-Speed Pumps
For Indoor or Outdoor Installations
Table of Contents
DATE OF INSTALLATION
INSTALLER INFORMATION
INITIAL PRESSURE GAUGE READING (WITH CLEAN FILTER)
PUMP MODEL HORSEPOWER
FILTER MODEL SERIAL NUMBER
CONTROLLER MODEL SERIAL NUMBER
NOTES:
EQUIPMENT INFORMATION RECORD
Section 1. IMPORTANT
SAFETY INSTRUCTIONS 3 ...................
1.1 Safety Instructions 3 .............................................
1.2 Pool Pump Suction Entrapment Prevention
Guidelines 6 ..........................................................
Section 2. Installation of the
Digital Controller 7 ................................
2.1 Introduction ........................................................7
2.2 The Controller Panel 7 ..........................................
2.3 The Controller Components 7 ...............................
2.3.1 Additional materials 8 .....................................
2.4 Installation of the Backplate
onto an Electrical Box 8 ........................................
2.5 Installation of the Backplate
on a Flat Wall 8 .....................................................
2.6 Connection to Jandy® Pro Series
variable-speed Pump 8 .........................................
2.7 Variable Speed Pump Switch Settings 9 ..............
2.8 Connection to Remote Contacts 9 ........................
2.9 Remote Operation 10 .............................................
2.10 Remote Closure 4 Behavior 10 ...............................
2.11 Remote Closure 4 Application
- Booster Pump Support 10 ....................................
Section 3. User Operation of the Variable-Speed
Controller ............................................ 11
3.1 The Controller Interface .....................................11
3.2 Basic Functions .................................................11
3.3 OFF Mode ..........................................................11
3.4 RUN Mode .........................................................11
3.5 Manual Start and Stop 12 .......................................
3.6 Pump Speed Setting 12 ..........................................
3.7 Timeclock Setup and Operation.........................12
3.8 Keypad Lock 13 ......................................................
Section 4. Service Setup Options 13 .......................
4.1 Entering Service Setup 13 ......................................
4.2 Minimum and Maximum Pump Speeds 13 .............
4.3 Load Defaults 14 .....................................................
4.4 Last Fault 14 ...........................................................
4.5 Priming Speed and Duration 14 ..............................
4.6 eStar Speed 15 .......................................................
4.7 Pump Freeze Protect Operation 15 ........................
4.8 Selecting Pump Type .........................................15
4.9 Display Power Usage 15 ........................................
Section 5. User Set Up Options 16 ...........................
5.1 Setting Time-of-Day ...........................................16
5.2 Labeling Speeds 16 ................................................
5.3 General Labels 16 ..................................................
5.4 Custom Labels 16 ...................................................
5.5 Display Light Control 16 ..........................................
5.6 Language Selection 17 ...........................................
5.7 Run Duration (Speeds 3 and 4 Only) 17 .................
5.8 Password Protect 17 ...............................................
Section 6. Menu Flow Chart 18 .................................
PAGE 2
ENGLISH JEP-R Variable-Speed Pump Controller | Installation Manual


Produkt Specifikationer

Mærke: JANDY
Kategori: Pomp
Model: JEP-R

Har du brug for hjælp?

Hvis du har brug for hjælp til JANDY JEP-R stil et spørgsmål nedenfor, og andre brugere vil svare dig




Pomp JANDY Manualer

JANDY

JANDY JCP07-3AT-S Manual

11 Januar 2025
JANDY

JANDY JCP07-3AT-N Manual

21 August 2024
JANDY

JANDY JCP07-1BD-S Manual

20 August 2024
JANDY

JANDY Stealth Manual

20 August 2024
JANDY

JANDY PlusHP Manual

20 August 2024
JANDY

JANDY VSSHP220AUT Manual

20 August 2024
JANDY

JANDY JCP15-3AT-N Manual

19 August 2024
JANDY

JANDY WaterFall Manual

18 August 2024
JANDY

JANDY VS FloPro Manual

18 August 2024

Pomp Manualer

Nyeste Pomp Manualer