JBL FS1000 Manual

JBL Ikke kategoriseret FS1000

Læs gratis den danske manual til JBL FS1000 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om JBL FS1000, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

FS1000

A Harman International Company

JBL Consumer Products

250 Crossways Park Drive, Woodbury, NY 11797 www.jbl.com

JBL is a registered trademark of Harman International Industries, Incorporated.

Part No. 406-000-05066

Speakers not included.

Included

For use…

…with all JBL

SCS200,

SCS260,

SCS30 and0

DSC systems

...with all JBL

SCS115,

SCS125,

SCS135,

SCS136,

SCS138,

SCS140,

SCS145,

SCS146,

SCS150,

SCS160,

SCS180

and ESC

systems

1. Assembly

1. Insert the

loudspeaker wire

through the cable

hole at the rear of

the top of the

upright. Feed the

wire through the

upright, all the

way down. Leave

approximately

20cm (8") of wire

out of the top of

the stand.

2. Lead the wire

through the hole

in the foot of the

stand. Place the

stand upright in

the foot and use

the supplied

screws to fit the

stand to the foot.

Note that the

stand upright

needs to be

inserted in such

a way that the

side of the foot

with the JBL logo

is facing forward

and the side of

the stand upright

with the hole on

the top is facing

toward the rear

of the stand foot.

2. Attach speaker

Depending on which speakers you would like to attach,

follow the steps below.

1. Attach the

stand adaptor

on the top of

the stand

upright as

shown. Note

that the side

with the pins

needs to be

toward the rear of the stand pole.

Fasten the adaptor to the stand

upright with the screw supplied.

2. Connect the loudspeaker wire to the

loudspeaker, respecting the polarity

(“+” and “–”; refer to the owner’s

manual of your loudspeakers).

3. Place the loudspeaker securely on

the stand, using the locating pin.

1. t the standInser

adaptor inside

the top of the

stand upright, as

shown in the image.

2. Take the bracket and

make sure that the

locking ring on the

bottom of the bracket

is rotated all the way up.

3. Screw the bracket into the adaptor

in the stand upright. Just before

the bracket has been screwed in

completely, position the bracket so that

the closed side is facing rearward.

Rotate the locking ring on the bottom

of the bracket down to tighten the

bracket to the stand.

4. Take the loudspeaker wire, and split

the two leads. Insert the two leads

through the hole on the back of the

bracket. Connect the loudspeaker wire

to the loudspeaker, respecting the

polarity (“+” and “–”; refer to the

owner’s manual of your loudspeakers).

5. Attach the loudspeaker to the bracket,

using the supplied screws.

SCS200, SCS260,

SCS300 and DSC

SCS115, SCS125, SCS135, SCS136,

SCS138, SCS140, SCS145, SCS146,

SCS150, SCS160, SCS180

and ESC variants

Thank you for choosing JBL

For more than 55 years, JBL has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you

play in your home, car or office. We’re confident that the JBL products you have chosen will provide every note of enjoyment that you expected – and that