JBL SUB150P Manual

JBL Subwoofer SUB150P

Læs gratis den danske manual til JBL SUB150P (4 sider) i kategorien Subwoofer. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om JBL SUB150P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Included Items

Your new JBL® SUB150P 300-watt powered subwoofer incorpo-

rates a 10" (250mm) PolyPlas™ cone transducer and a built-in

high-performance 300-watt (RMS) amplifier that deliver the power-

ful, dynamic and accurate low-frequency performance that makes

your film soundtracks and music come alive. And with line-level

and LFE inputs, adjustable crossover and phase controls and

automatic turn on/off, the SUB150P is also simple to connect and

set up.

We’re confident that this JBL subwoofer will provide every note of

enjoyment that you expect – and that when you think about pur-

chasing additional audio equipment for your home, car or office,

you will once again choose JBL products.

This quick-start guide contains all the information you need to set

up, connect and adjust your new subwoofer. For more in-depth

information, go to our Web site: www.jbl.com.

thank You For choosIng thIs JBl® Product

suB150P

300-Watt, 10" (250mm) Powered Subwoofer

quIck-start guIde

Phase Switch: This switch determines whether the subwoofer transduc-

er's piston-like action moves in and out in phase with the main speakers.

If the subwoofer were to play out of phase with the main speakers, the

sound waves from the main speakers could partially cancel out the sound

waves from the subwoofer, reducing bass performance and sonic impact.

This phenomenon depends in part on the placement of all the speakers

relative to the listening position and to each other in the room.

Input Mode Switch: When this switch is in the “Normal” setting, the input

signal from both Line In connectors is routed through the subwoofer's

built-in low-pass crossover network. When the switch is in the “LFE” set-

ting, the input signal from the LFE Input connector bypasses the subwoof-

er's built-in crossover network.

Volume Control: Use this control to adjust the subwoofer’s volume. Turn

the knob clockwise to increase the volume; turn the knob counterclock-

wise to decrease the volume.

Crossover Control: This control determines the highest frequency at

which the subwoofer reproduces sounds. The higher you set the Cross-

over control, the higher in frequency the subwoofer will operate and the

more its bass will “overlap” that of the satellite speakers. This adjust-

ment helps achieve a smooth transition of bass frequencies between the

subwoofer and the satellites for a variety of different rooms and subwoofer

locations.

NOTE: The Crossover Control functions only when the Input Mode switch

is in the “Normal” setting.

On/Standby LED: When the Power switch is in the “On” position, this

LED indicates whether the subwoofer is in the On or Standby state:

• When the LED glows green, the subwoofer is turned on.

• When the LED glows red, the subwoofer is in the Standby mode.

Line In/LFE Input Connectors:

• When you’re connecting the subwoofer to the dedicated subwoofer

output of a receiver/processor that has its own low-pass crossover

network, use the LFE Input connector and set the Input Mode switch

in the “LFE” position.

• When you're connecting the subwoofer to the preamp or subwoofer

outputs of a receiver/processor that does not have its own low-pass

crossover network, use both Line In connectors and set the Input

Mode switch in the “Normal” position. If your receiver/processor only

has one subwoofer output you can use either Line In connector.

Power Switch: Set this switch in the “On” position to turn the subwoofer

on. The subwoofer will then be in the Standby mode. It will automatically

turn On when an audio signal is detected at its inputs, and will return to the

Standby mode when no audio signal is detected its inputs after approxi-

mately 10 minutes.

If you will be away from home, or will not be using the subwoofer for an

extended period, set this switch in the “Off” position to conserve energy.

Power Cord Connector: After you have made and veriﬁed the subwoof-

er’s input connections, plug the female end of the supplied IEC power cord

into the subwoofer’s Power Cord connector, and plug the other end of the

power cord into an active, electrical outlet for proper opera-unswitched

tion of the subwoofer. plug the power cord into the accessory DO NOT

outlets found on some audio components.

suBwooFer rear-Panel controls and connectIons

2053 23

No rt hr id ge , CA USA

De sign ed and e n gi ne er ed i n USA

Made in P.R.C

SUB150P

Phase Switch

Input Mode Switch

Volume Control

Crossover Control

On/Standby LED

Power Switch

Line-Level/LFE

Input Connectors

Power Cord

Connector

Produkt Specifikationer

Mærke:	JBL
Kategori:	Subwoofer
Model:	SUB150P

Har du brug for hjælp?

Hvis du har brug for hjælp til JBL SUB150P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Subwoofer JBL Manualer

11 Marts 2025

11 Marts 2025

26 Februar 2025

26 Februar 2025

JBL Club 1000SSL Manual

11 Februar 2025

JBL Club 1200SSL Manual

11 Februar 2025

JBL SSW-4 Manual

26 December 2024

JBL SSW-2 Manual

26 December 2024

JBL 800.4GTi Manual

25 December 2024

JBL Grand Touring GTO1212BP Manual

25 December 2024

Subwoofer Manualer

Nyeste Subwoofer Manualer

Rockustics SubScape 12 Manual

19 Juni 2025

Planet Audio P10AWK Manual

19 Juni 2025

Wharfedale WH-S8E Manual

19 Juni 2025

Wharfedale WH-S10E Manual

19 Juni 2025

Planet Audio PL12S Manual

19 Juni 2025

Rockustics SubScape 8 Manual

18 Juni 2025

Rockustics Subscape 10 Manual

18 Juni 2025

Planet Audio PL10S Manual

18 Juni 2025

MB Quart RW1-164 Manual

18 Juni 2025

MB Quart DS1-254 Manual

17 Juni 2025