JennAir YJMV9196CS Manual

JennAir Mikrobølgeovn YJMV9196CS

Læs gratis den danske manual til JennAir YJMV9196CS (32 sider) i kategorien Mikrobølgeovn. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om JennAir YJMV9196CS, eller vil du spørge andre brugere om produktet?

Side 1/32
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See the “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration
in these installation instructions.
INSTRUCTIONS D’UTILISATION DE LENSEMBLE
HOTTE/FOUR À MICRO-ONDES
Ce produit peut être installé au-dessus de produits de cuisson électriques ou au gaz d’une largeur maximale de 36po (91,4cm).
Voir la section « Exigences d’installation » pour plus de renseignements.
Ces instructions d’installation couvrent plusieurs modèles. L’apparence de votre modèle peut différer légèrement des illustrations
présentes dans ces instructions d’installation.
Table of Contents / Table des matières
W11493662A
MICROWAVE HOOD COMBINATION SAFETY ..................................2
INSTALLATION REQUIREMENTS .......................................................2
Tools and Parts ..................................................................................2
Separate Cardboard Template ..........................................................3
Location Requirements ...................................................................... 3
Product Dimensions...........................................................................3
Electrical Requirements ..................................................................... 4
INSTALLATION INSTRUCTIONS .........................................................5
Remove Mounting Plate ....................................................................5
Rotate Blower Motor .......................................................................... 5
Locate Wall Stud(s) ............................................................................ 8
Mark Rear Wall ...................................................................................9
Drill Holes in Rear Wall ..................................................................... 10
Attach Mounting Plate to Wall ......................................................... 10
Prepare Upper Cabinet ....................................................................11
Install Damper Assembly
(for wall venting only) .......................................................................11
Install the Microwave Oven .............................................................. 12
Complete Installation .......................................................................13
VENTING DESIGN SPECIFICATIONS ..............................................14
ASSISTANCE ......................................................................................15
Replacement Parts ..........................................................................15
Accessories ......................................................................................15
SÉCURITÉ DE L’ENSEMBLE HOTTE/FOUR À MICRO-ONDES .... 16
EXIGENCES D’INSTALLATION .........................................................16
Outils et pièces ................................................................................16
Gabarit en cartonparé ................................................................. 17
Exigences d’emplacement ..............................................................17
Dimensions du produit .....................................................................18
Spéci cationsélectriques ................................................................ 18
INSTRUCTIONS D’INSTALLATION ...................................................19
Dépose de la plaque de montage ...................................................19
Réorientation du moteur du ventilateur ...........................................19
Identi cation de la position des montants de cloison .....................22
Tracé sur le mur arrière ....................................................................23
Perçage de trous dans le mur arrière ..............................................24
Fixation de la plaque de montage au mur .......................................24
Préparation de l’armoire supérieure ................................................25
Installation du registre (pour décharge à travers le mur uniquement) ................................. 25
Installation du four à micro-ondes ...................................................26
Terminer l’installation .......................................................................27
SCIFICATIONS/CONCEPTION DU CIRCUIT D’ÉVACUATION .28
ASSISTANCE ......................................................................................30
Pièces de rechange .........................................................................30
Accessoires ......................................................................................30
2
MICROWAVE HOOD COMBINATION SAFETY
INSTALLATION REQUIREMENTS
Tools and Parts
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Measuring tape
Pencil
Masking tape or thumbtacks
Scissors
No. 2 Phillips screwdriver
No. 3 Phillips screwdriver
for 1/4-20 x 3" (7.6 cm)
bolts
Drill
3/16" (5 mm), 3/8" (10 mm),
5/8" (16 mm) drill bits
3/4" (19 mm) hole saw
Diagonal wire cutting pliers
Stud  nder
7⁄16" (11.11 mm) socket wrench (or box wrench) for 1/4" x 2"
(6.4 mm x 5.1cm) lag screws
11/2" (3.8 cm) diameter hole drill bit for wood or metal cabinet
Keyhole saw
Caulking gun and weatherproof caulking compound
Duct tape
Parts Supplied
For information on reordering, see the “Replacement Parts”
section.
NOTE: The hardware items listed here are for wood studs.
For other types of wall structures, be sure to use appropriate
fasteners.
NOTE: Depending on model, aluminum grease  lter and
charcoal  lter may be combined.
Materials Needed
Standard fi ttings for wall or roof venting. See the “Venting
Design Specifi
cations” section
.
A B C D E F G
H
A. 3/16-24 x 3" round-head
bolts (2)
B. 1/4-20 x 3"  at-head bolts (2)
C. Washers (2)
D. 3/16" toggle nuts (2)
E. 1/4" x 2" lag screws (2)
F. Sheet metal screws 1/8" x 3/8"
(3.2 mm x 9.5 mm) (2)
G. Power supply cord bushing (1)
H. Damper assembly (for wall or
roof venting)
Not Shown:
Mounting plate (attached to
back of microwave oven)
Cardboard template (part of
packaging)
Aluminum grease lters
Charcoal lters (Depending
on model, charcoal  lters may
not be included. See User
Instructions.)


Produkt Specifikationer

Mærke: JennAir
Kategori: Mikrobølgeovn
Model: YJMV9196CS

Har du brug for hjælp?

Hvis du har brug for hjælp til JennAir YJMV9196CS stil et spørgsmål nedenfor, og andre brugere vil svare dig




Mikrobølgeovn JennAir Manualer

Mikrobølgeovn Manualer

Nyeste Mikrobølgeovn Manualer