JET JT1-1371 Manual

JET Sav JT1-1371

Læs gratis den danske manual til JET JT1-1371 (40 sider) i kategorien Sav. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om JET JT1-1371, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/40
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-JT1-1371
Ph.: 800-274-6848 Edition 2 08/2024
www.jettools.com Copyright © 2024 JET
Operating Instructions and Parts Manual
14-inch Woodworking Band Saw
Model JWBS-14SFX-BLK
2
1.0 Safety Warnings
1. Read and understand the entire owner's
manual before attempting assembly or
operation.
2. Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury.
3. Replace warning labels if they become
obscured or removed.
4. This band saw is designed and intended for use
by properly trained and experienced personnel
only. If you are not familiar with the proper and
safe operation of a band saw, do not use until
proper training and knowledge have been
obtained.
5. Do not use this band saw for anything other
than its intended use. If used for other
purposes, JET disclaims any real or implied
warranty and holds itself harmless from any
injury that may result from that use.
6. This machine has an industrial-grade low-
friction corrosion-resistant coating we call JET
Black. This coating is on the table. While the
JET Black coating is durable, it can be
damaged if metal or other hard and/or sharp
objects strike, gouge, or scratch the surface.
Significant damage to the coating may affect its
performance.
7. Always wear approved safety glasses/face
shield while using this machine. (Everyday
eyeglasses only have impact resistant lenses;
they are not safety glasses.)
8. Before operating band saw, remove tie, rings,
watches and other jewelry, and roll sleeves up
past the elbows. Remove all loose clothing and
confine long hair. Non-slip footwear or anti-skid
floor strips are recommended. Do not wear
gloves.
9. Keep work area clean. Keep floor around
machine clean and free of scrap material, oil,
and grease. Dirty floors and cluttered invite
accidents.
10. Use proper extension cord. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will
draw. An undersized cord will cause a drop in
line voltage resulting in loss of power and
overheating. Sect. 6.3, Table 1 shows the
correct size to use depending on cord length
and nameplate ampere rating. If in doubt, use
the next heavier gage. The smaller the gage
number, the heavier the cord.
11. Secure work. Use clamps or a vise to hold work
when practical. It’s safer than using your hand
and it frees both hands to operate tool.
12. Disconnect tools from power before servicing;
when changing accessories, such as blade,
bits, cutters and the like.
13. Adjust upper blade guides to just clear
workpiece (approximately 3/16”).
14. Make sure blade tension, tracking, and blade
guides are all properly adjusted.
15. Make relief cuts where possible, when cutting
curved stock.
16. When feeding small work pieces into blade,
always use push stick, fixture, or similar device
to keep hands at a safe distance.
17. Hold stock firmly and flat against table.
18. Wear ear protectors (plugs or muffs) during
extended periods of operation.
19. Do not operate this machine while tired or under
the influence of drugs, alcohol or any
medication.
20. Make certain switch is in OFF position before
connecting machine to power supply.
21. Make certain machine is properly grounded.
22. Do not back stock out of blade while blade is
running.
23. Do not remove jammed cutoff pieces until the
OFF button is pressed and the blade has
stopped.
24. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and adjusting
wrenches are removed from the machine
before turning it on.
25. Keep safety guards in place at all times when
machine is in use. If removed for maintenance
purposes, use extreme caution and replace the
guards immediately after completion of
maintenance.
26. Check damaged parts. Before further use of
machine, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or
replaced.
27. Keep visitors a safe distance from work area.
Keep children away.

Produkt Specifikationer

Mærke: JET
Kategori: Sav
Model: JT1-1371

Har du brug for hjælp?

Hvis du har brug for hjælp til JET JT1-1371 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Sav JET Manualer

JET

JET JT1-1371 Manual

8 Oktober 2025

Sav Manualer

Nyeste Sav Manualer

SHOPMAX

SHOPMAX SS0245 Manual

8 Oktober 2025
Flex

Flex FX2141R Manual

8 Oktober 2025
Skil

Skil JS314901 Manual

7 Oktober 2025
NEO Tools

NEO Tools 04-633 Manual

7 Oktober 2025
NEO Tools

NEO Tools 04-632 Manual

7 Oktober 2025
Shindaiwa

Shindaiwa CWT-7410 Manual

6 Oktober 2025
Shindaiwa

Shindaiwa EC7500W Manual

6 Oktober 2025
Hilti

Hilti DST WRC-CA Manual

6 Oktober 2025
Shindaiwa

Shindaiwa 493 Manual

6 Oktober 2025
Shindaiwa

Shindaiwa 251TS Manual

6 Oktober 2025