JET JWDS-1632OSC Manual

JET Rysteplaster JWDS-1632OSC

Læs gratis den danske manual til JET JWDS-1632OSC (32 sider) i kategorien Rysteplaster. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om JET JWDS-1632OSC, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/32
Operating Instructions and Parts Manual
Drum Sander
Model JWDS-1632OSC
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-723525
Ph.: 800-274-6848 Edition 1 12/2022
www.jettools.com Copyright ©2022 JET
Shown with optional infeed/outfeed tables
2
1.0 IMPORTANT SAFETY
INSTRUCTIONS
WARNING – To reduce risk of injury:
1. Read and understand the entire owner's
manual before attempting assembly or
operation.
2. Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all warnings may cause serious
injury.
3. Replace warning labels if they become
obscured or removed.
4. This drum sander is designed and intended for
use by properly trained and experienced
personnel only. If you are not familiar with the
proper and safe operation of a drum sander, do
not use until proper training and knowledge
have been obtained.
5. Do not use this drum sander for other than its
intended use. If used for other purposes, JET
disclaims any real or implied warranty and holds
itself harmless from any injury that may result
from that use.
6. Always wear ANSI Z87.1 approved safety
glasses or face shield while using this drum
sander. (Everyday eyeglasses only have impact
resistant lenses; they are not safety glasses.)
7. Before operating this machine, remove tie,
rings, watches and other jewelry, and roll
sleeves up past the elbows. Do not wear loose
clothing. Confine long hair. Non-slip footwear or
anti-skid floor strips are recommended. Do not
wear gloves.
8. Kickback occurs when the workpiece is thrown
towards the operator at a high rate of speed. If
you do not have a clear understanding of
kickback and how it occurs, DO NOT operate
this drum sander.
9. Wear hearing protection (plugs or muffs) during
extended periods of operation.
10. Do not operate this machine while tired or under
the influence of drugs, alcohol, or any
medication.
11. Make certain the switch is in the OFF position
before connecting the machine to the power
supply.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance
with the machine unplugged from the power
source.
14. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and adjusting
wrenches are removed from the machine
before turning it on.
15. Keep safety guards in place at all times when
the machine is in use. If removed for
maintenance purposes, use extreme caution
and replace the guards immediately after
completion of maintenance.
16. Make sure the sander is firmly secured to the
stand or work table before use.
17. Check damaged parts. Before further use of the
machine, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or
replaced.
18. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
19. Keep the floor around the machine clean and
free of scrap material, oil and grease.
20. Keep visitors a safe distance from the work
area. Keep children away.
21. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
22. Give your work undivided attention. Looking
around, carrying on a conversation and “horse-
play” are careless acts that can result in serious
injury.
23. Maintain a balanced stance at all times so that
you do not fall onto moving parts. Do not
overreach or use excessive force to perform
any machine operation.
24. Use the right tool at the correct speed and feed
rate. Do not force a tool or attachment to do a
job for which it was not designed. The right tool
will do the job better and more safely.
25. Use recommended accessories; improper
accessories may be hazardous.
26. Maintain tools with care. Keep conveyor and
abrasives clean for the best and safest
performance. Follow instructions for lubricating
and changing accessories.
27. Turn off the machine before cleaning. Use a
brush or compressed air to remove chips or
debris — do not use bare hands.
28. Do not stand on the machine. Serious injury
could occur if the machine tips over.

Produkt Specifikationer

Mærke: JET
Kategori: Rysteplaster
Model: JWDS-1632OSC

Har du brug for hjælp?

Hvis du har brug for hjælp til JET JWDS-1632OSC stil et spørgsmål nedenfor, og andre brugere vil svare dig


Rysteplaster JET Manualer

JET

JET JT1-1372 Manual

8 Oktober 2025
JET

JET JWDS-1632OSC Manual

8 Oktober 2025

Rysteplaster Manualer

Nyeste Rysteplaster Manualer

Bosch Blauw

Bosch Blauw GDA 280 E Professional Manual

5 Oktober 2025
Bosch Blauw

Bosch Blauw GBS 75 AE Professional Manual

5 Oktober 2025
Draper

Draper 65084 Manual

3 Oktober 2025
Fein

Fein WSG 17-125 PSQ Manual

2 Oktober 2025
Fein

Fein WPO 14-25 E Set Manual

2 Oktober 2025
Stanley

Stanley FatMax SFMCG400M2K Manual

1 Oktober 2025
Fein

Fein WSG 17-150 PQ Manual

1 Oktober 2025
Chicago Pneumatic

Chicago Pneumatic CP7255CVE Manual

1 Oktober 2025
Fein

Fein WSG 15-125 PR Manual

1 Oktober 2025
Fein

Fein CG 17-125 Inox Manual

1 Oktober 2025