Information
What’s in the Box
1 Range Extender with built-in
100–240 V power adapter;
1 Ethernet cable;
1 Quick Start Guide;
1 Quick Start Guide (multilingual).
Safety Instructions
Your Keenetic device is ONLY for indoor
use — NEVER use it outside.
Before use, remove protective labels from
your Keenetic device, and ensure vents are
unblocked.
Never use your Keenetic device
in an enclosed space, and ensure that
is always easily accessible.
Cease to use any damaged Keenetic device
IMMEDIATELY.
Your Keenetic device contains
no user-serviceable parts — DO NOT OPEN.
Keep your Keenetic device away from
water, excessive humidity or heat, and
direct sunlight.
Environmental Conditions
Operating temperature range: 0 +40°C;to
Operating humidity: 20 95% to
non-condensing;
Storage temperature range: –30 +70°C;to
Storage humidity: 10 95% to
non-condensing.
Device Warranty
For the most up date Warranty to
Information, please visit our website
keenetic.com/legal.
Your Keenetic device comes with
a non-transferable 3-year warranty
from the documented date of purchase
(including your 2-year European
Limited Warranty). Valid claims in case
of a defect will be honored subject to local
legal requirements.
Certication Information
Keenetic Limited hereby declares that this
device is in compliance with all relevant
provisions of directives 2014/53/EU,
2009/125/EC, and 2011/65/EU. Details
of the original EU declaration may be found
at within details onkeenetic.com specic
model pages.
This device complies with EU radiation
exposure limits set forth for an uncontrolled
environment.
This equipment should be installed
and operated with a minimum distance
of 20 cm between the antennas and
a person’s body.
The frequency and the maximum transmitted
power for your device, per the requirements
of the EU are listed below:
2400-2483,5 MHz: 20 dBm.
Per (EC) No 1275/2008, the power
consumption in networked standby if all
wired network ports are connected and all
wireless network ports are activated is 2 W.
This device can be used across
EU member states.
Disposal
In accordance with European
directives, your Keenetic device,
including cables may not be disposed
of with general household waste.
Consult your local authority
or your supplier for information
about disposal.
Notice
When you use your Keenetic device
(including when you connect your Keenetic
device the rst time), Keenetic Limited will
process certain personal data about you,
e.g., service tag, serial number, model name,
software version, and IP address of your
Keenetic device.
For more information, please go to
keenetic.com/legal.
If you are in the European Union / European
Economic Area, Keenetic GmbH will process
certain personal data about you, e.g., service
tag, serial number, model name, software
version, and IP address of your Keenetic
device. Please read our Device Privacy
Notice for the European Union / European
Economic Area at keenetic.com/legal.
Buddy 4 Details
1. Wi-Fi Antennas
Two xed Wi-Fi antennas. We recommend
keeping the antennas in a vertical position.
2. Wi-Fi LED D
Solid green — Good connection with
the main router. Internet accesible.
Blinking green — Rebooting
or updating the operating system.
Rapidly blinking green for 2 seconds —
Wi-Fi Control Button has been pressed. Quick
connection session (WPS) has started.
Solid blue — Too far from router.
Relocate closer to the router for better
performance. Internet accesible.
Blinking blue — Range Extender is on the
factory settings. Has connection to the
main router. Initial Setup incomplete.
Solid red — No connection to the
main router or no Internet access.
Blinking red — Range Extender is on the
factory settings. Initial Setup incomplete.
Off — Off.
3. Wi-Fi Control Button D
By default, this button allows you to easily add
extenders to the Keenetic Mesh Wi-Fi System,
or other WPS-compliant devices to the
wireless network.
Pressing it once — Starts a quick connection
session for adding a new device.
Pressing and holding for 10 seconds —
Restores the original factory settings and
resets the administrator password.
4 Network Port.
This port is intended to connect any
wired device to the Internet or establish
a wired backhaul to the router for
optimal performance.
5. Power plug
The Keenetic Range Extender is designed
for continuous operation and does not need
to be powered off daily.
Questions
What should I do if I can’t access the
Initial Setup Wizard page?
1. Make sure that your mobile device /
computer is connected to the Keenetic_
Extender_Setup Wi-Fi network and is set
up obtain an IP address and DNS servers to
automatically.
2. Check that you have correctly entered
the appropriate web address: either
my.keenetic.net (recommended)
or .192.168.1.3
3. Reboot your mobile device / computer and
your Keenetic Wi-Fi Range Extender.
4. If the Initial Setup Wizard page is still not
appearing, please follow the instructions
below to reset your Range Extender.
What should I do if I can’t access
the Internet with my Keenetic
Wi-Fi Range Extender?
1. If the on the Range Extender Wi-Fi LED D
is steady red:
a. Check if your main router is on and
operating normally and has access to the
Internet.
b. In case the network name or password
of the main router has been changed,
or the router was replaced, reset the
Range Extender to factory settings and
set it up again.
c. Make sure your Range Extender is within
the range of your main router. In case
of wired connection check the cable.
2. If the on the Range Extender Wi-Fi LED D
is steady green make sure that your
mobile device / computer is connected
to the right Wi-Fi network and set
up obtain an IP address and DNS servers to
automatically. In case of wired connection
check the cable.
How do I reset/restore the original
factory settings on my Keenetic
Wi-Fi Range Extender?
Make sure that your Range Extender
is connected to a power supply. Press and
hold the Wi-Fi Control Button until the D
Wi-Fi LED begins to blink green rapidly, D
release the button and wait while your device
restarts.
Important: After restoring factory settings,
you will need to re-add the Range Extender
to your Mesh Wi-Fi System.
