Kemppi A7 MIG Welder 450 Manual

Kemppi Svejseapparat A7 MIG Welder 450

Læs gratis den danske manual til Kemppi A7 MIG Welder 450 (66 sider) i kategorien Svejseapparat. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Kemppi A7 MIG Welder 450, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/66

350, 450

1920310

1804

A7 MIG WelderA7 MIG Welder

INTEGRATION GUIDE

2A7 MIG Welder© Kemppi Oy 2018 1804

CONTENTS

1. Introduction ..........................................................................................4

2. Integration step by step ...................................................................4

3. Hardware installation ........................................................................5

3.1 Procedures before use ..............................................................................5

3.2 System overview .......................................................................................5

3.3 Power source .............................................................................................7

3.4 Cooling unit ...............................................................................................7

3.5 Wire feeder ................................................................................................7

3.6 Welding torch ............................................................................................9

3.6.1 Mounting .............................................................................................. 9

3.6.2 Push-pull torches ....................................................................................9

3.6.3 Wire inch button ....................................................................................9

3.6.4 Torch-cleaning with compressed air ...........................................................9

3.6.5 Touch-sensing with the gas nozzle ...........................................................10

3.7 Collision sensor .......................................................................................10

3.8 Interconnection cable set .......................................................................11

3.8.1 The arc measurement cable ....................................................................11

3.8.2 Wire feeder control cable .......................................................................12

3.8.3 Welding cable ......................................................................................12

3.8.4 Shielding gas hose ................................................................................12

3.8.5 Cooling hoses ......................................................................................12

3.9 Fieldbus communication ........................................................................13

3.10 Ethernet (web user interface server) ......................................................14

3.11 Emergency input functions ....................................................................14

3.12 Touch sensor status fast output ..............................................................15

3.13 I/O device ................................................................................................16

3.13.1 Installation ..........................................................................................16

3.13.2 Inputs ................................................................................................19

3.13.3 Outputs ..............................................................................................20

3.14 Dual wire feeder support ........................................................................21

3.14.1 Installation ..........................................................................................22

3.14.2 Connect the second wire feeder ..............................................................24

3.15 Powering up ............................................................................................24

4. Accessing the Web user interface ..............................................25

4.1 Conguring the network settings ..........................................................25

4.2 Opening the web user interface ............................................................26

5. System configuration ......................................................................27

5.1 Welding system, sensors and devices ....................................................27

5.1.1 General settings ...................................................................................27

5.1.2 Wire feed settings .................................................................................27

5.1.3 Gas sensor settings ...............................................................................28

5.1.4 General robot settings ...........................................................................29

5.1.5 Touch sensor settings ............................................................................29

5.1.6 Collision sensor settings ........................................................................29

5.1.7 Emergency stop settings ........................................................................29

5.1.8 Watchdog settings ................................................................................30

5.1.9 Welding system time .............................................................................30

5.2 Digital robot interface .............................................................................31

5.2.1 Fieldbus settings ..................................................................................31

5.2.2 Selecting the proper I/O table .................................................................31

5.2.3 Setting up scaling values .......................................................................32

5.3 Users ........................................................................................................34

5.4 Inputs and outputs ..................................................................................35

5.4.1 Inputs ................................................................................................35

5.4.2 Outputs ..............................................................................................35

5.5 Memory channels ....................................................................................36

5.6 System backup ........................................................................................36

6. Digital robot interface .....................................................................37

6.1 Control functions ....................................................................................37

6.1.1 WireFeedSpeed ....................................................................................38

6.1.2 Voltage ...............................................................................................38

6.1.3 FineTuning ..........................................................................................39

6.1.4 Dynamics ............................................................................................39

6.1.5 MemoryChannel ..................................................................................39

INTEGRATION GUIDE

Produkt Specifikationer

Mærke:	Kemppi
Kategori:	Svejseapparat
Model:	A7 MIG Welder 450

Har du brug for hjælp?

Hvis du har brug for hjælp til Kemppi A7 MIG Welder 450 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Svejseapparat Kemppi Manualer

Kemppi KempCool 10 Manual

5 Oktober 2024

Kemppi Master MLS 3500 Manual

22 September 2024

Kemppi FastMig M 320 Manual

22 September 2024

Kemppi MinarcTig Evo 200 Manual

21 September 2024

Kemppi FastMig X 350MV Manual

21 September 2024

Kemppi A7 Robot Gun Mount T4 Manual

20 September 2024

Kemppi A7 MIG gun - 500g Manual

19 September 2024

Kemppi FastMig KMS 400 Manual

17 September 2024

Kemppi A3 MIG Power Source 400 Manual

23 August 2024

Kemppi FastMig WFX 300 Manual

22 August 2024

Svejseapparat Manualer

Nyeste Svejseapparat Manualer

GYS P1 Auto Manual

11 September 2025

Lincoln Electric Tandem Cruiser Manual

8 September 2025

Lincoln Electric Power Wave Advanced Module Manual

8 September 2025

Lincoln Electric Ranger Air 260MPX Manual

8 September 2025

Lincoln Electric POWER MIG 210 MP Manual

8 September 2025

Lincoln Electric Vantage 441X Manual

7 September 2025

Lincoln Electric Miniflex Manual

7 September 2025

Lincoln Electric POWER MIG 140/180 Manual

7 September 2025

Guede 100 GC Manual

7 September 2025

Lincoln Electric Power Wave Connectivity Hub Kit Manual

7 September 2025