Kenwood DNX710EX Manual

Kenwood GPS-enhed DNX710EX

Læs gratis den danske manual til Kenwood DNX710EX (5 sider) i kategorien GPS-enhed. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Kenwood DNX710EX, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

DNX7100

DNX710EX

GPS NAVIGATION SYSTEM

INSTALLATION MANUAL

SYSTÈME DE NAVIGATION GPS

MANUEL D’INSTALLATION

SISTEMA DE NAVEGACIÓN GPS

MANUAL DE INSTALACIÓN

English | 3

Installation Procedure

1. To prevent a short circuit, remove the key from the

ignition and disconnect the - battery.

2. Make the proper input and output wire

connections for each unit.

3. Connect the speaker wires of the wiring harness.

4. Connect the wiring harness wires in the following

order: ground, battery, ignition.

5. Connect the wiring harness connector to the unit.

6. Install the unit in your car.

7. Reconnect the - battery.

8. Press the reset button.

2WARNING

• If you connect the ignition wire (red) and the battery wire

(yellow) to the car chassis (ground), you may cause a short

circuit, that in turn may start a fire. Always connect those

wires to the power source running through the fuse box.

• Do not cut out the fuse from the ignition wire (red) and the

battery wire (yellow). The power supply must be connected

to the wires via the fuse.

Acquiring GPS Signals

The first time you turn on the DNX7100/DNX710EX,

you must wait while the system acquires satellite

signals for the first time. This process could take up to

several minutes. Make sure your vehicle is outdoors

in an open area away from tall buildings and trees for

fastest acquisition. After the system acquires satellites

for the first time, it will acquire satellites quickly each

time thereafter.

• If the power is not turned ON (or it is ON, but will be OFF

immediately), the speaker wire may have a short-circuit

or touched the chassis of the vehicle and the protection

function may have been activated. Therefore, the speaker

wire should be checked.

• If your car’s ignition does not have an ACC position, connect

the ignition wires to a power source that can be turned on

and off with the ignition key. If you connect the ignition

wire to a power source with a constant voltage supply, as

with battery wires, the battery may die.

• If the console has a lid, make sure to install the unit so that

the faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps

on the ends of the unconnected wires or the terminals.

• Connect the speaker wires correctly to the terminals to

which they correspond. The unit may be damaged or fail to

work if you share the - wires or ground them to any metal

part in the car.

• When only two speakers are being connected to the

system, connect the connectors either to both the front

output terminals or to both the rear output terminals (do

not mix front and rear). For example, if you connect the +

connector of the left speaker to a front output terminal, do

not connect the connector to a rear output terminal.-

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Mount the unit so that the mounting angle is 30° or less.

• This unit has the cooling fan (page 5) to decrease the

internal temperature. Do not mount the unit in a place

where the cooling fan of the unit are blocked. Blocking

these openings will inhibit the cooling of the internal

temperature and result in malfunction.

Produkt Specifikationer

Mærke:	Kenwood
Kategori:	GPS-enhed
Model:	DNX710EX

Har du brug for hjælp?

Hvis du har brug for hjælp til Kenwood DNX710EX stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

GPS-enhed Kenwood Manualer

Kenwood DMX908S Manual

29 August 2024

Kenwood DNX7032 Manual

6 August 2024

Kenwood DNX8022BT Manual

6 August 2024

Kenwood DNX8032BT Manual

4 August 2024

Kenwood DNX5120 Manual

3 August 2024

Kenwood DNR-1000U Manual

28 Juli 2024

Kenwood DNX6160 Manual

28 Juli 2024

Kenwood DNX812 Manual

25 Juli 2024

Kenwood DNX891HD Manual

20 Juli 2024

Kenwood DNX6040EX Manual

20 Juli 2024

GPS-enhed Manualer

Nyeste GPS-enhed Manualer

4smarts SkyTag Plus Manual

30 Juli 2025

SpyTec GL300 Tracker Manual

23 Juli 2025

Family1st Portable GPS Tracker Manual

16 Juli 2025

LandAirSea SilverCloud Manual

15 Juli 2025

SinoTrack ST-904L 4G Manual

30 Juni 2025

SinoTrack ST-906W Manual

30 Juni 2025

Holux GR-213 Manual

7 Juni 2025

Amod AGL3080 Manual

6 Juni 2025

Power Acoustik NAVIBOX-1 Manual

6 Juni 2025

Holux M-1000 Manual

6 Juni 2025