Keystone KSTAW10BE Manual

Keystone Klimaanlæg KSTAW10BE

Læs gratis den danske manual til Keystone KSTAW10BE (4 sider) i kategorien Klimaanlæg. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Keystone KSTAW10BE, eller vil du spørge andre brugere om produktet?

Side 1/4
4
INSTALLATION INSTRUCTIONS
Read these instructions completely
and carefully.
IMPORTANT- Save these
instructions for local inspector s use.
IMPORTANT- Observe all
governing codes and ordianaces.
Note to Consumer-Keep these
instructions for futrue reference.
Note to Installer-Be sure to leave these
instructions with the Consumer.
Completion time-Approximately 1 hour.
Skill level-Installatio of this appliance
requires basic mechanical skills.
We recommend that two people install
this product.
Proper installation is the responsibility
of the installer.
Product failure due to improper installation
is not covered under the Warranty.
You MUST use all supplied parts and use
proper installation procedures as described
in these instructions when installing this air
conditioner.
BEFORE YOU BEGIN
Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord.
CAUTION
Do not change the plug on the power cord
of the air conditioner.
Aluminum house wiring may present special
problems- consult a qualified electircian.
When handling unit, be careful to avoid cuts from
sharp metal edges and aluminum fins on front and
rear coils.
TOOLS YOU WILL NEED
Screwdriver
Level
TOOLS YOU MAY USE
Screwdriver
Pencil
Ruler or tape measure
Scissors or knife
Save Carton and these Installation Instructions
for future reference. The carton is the best way
to store unit during winter, or when not in use.
NOTE:
H
Your air conditioner is designed to install in
standard double hung windows with opening
widths of 23 to 36 inches(584mm to 914mm) .
WINDOW REQUIREMENTS
Model
H
600 0~8000Btu/ h 10000~12000Btu/h
14 (356mm) 15-1/2 (394mm)
Table 1
Fig.C
NOTE: The top rail hardware and the Fig.A,
Fig.B and Fig.C are not applicable to the units
more than 10000B tu/h.Before installing unit,
the top rail must be assembled on the unit (For
<10000Btu/h models only).
5
INSTALLATION INSTRUCTIONS
Lower sash must open sufficiently to allow a clear
vertical opening (H) of following size (see Table 1).
Side louvers and the rear of the AC must have clear
air space to allow enough airflow through the
condenser,for heat removal. The rear of the unit must
be outdoors, not inside a building or garage.
PREPARE THE WINDOW
3/4 (or 1/ )
Scre ws
(7)
2Lock Frame
(2)
Sash Lock
(1)
Mounting Hardware
Wind ow sash
seal foam
(1)
PREPARE AIR CONDITIONER
A: Remove the air conditioner from the carton and
place on a flat surface.
B: Remove top rail from the packaging material as
shown in Fig. A.
Top Rail Hardware
3/8 Scre ws
(4)
Top Rail
(1)
Packaging
Fig.A
Top Rail
C: Align the hole in the top rail with those in the top
of the unit as shown in Fig.B
D: Secure the top rail to the unit with the 3/8 Screws
as shown in Fig.C.
For safety reasons, all four(4) screws MUST
be securely fastened.
NOTE:
INSTALL THE ACCORDION PANELS
NOTE: Top rail and Sliding Panels at each side are
offset to provide the proper pitch to the rear of (5/16 ).
This is necessary for proper condensed water
utilization and drainage. If you are not using the Side
Panels for any reason, this pitch to the rear must be
maintained.
A.Place unit on floor, a bench or
a table. Hold the Accordion
Panel in one hand and gently
pull back the center to free the
open end. See Fig.1
Fig.1
Fig.B


Produkt Specifikationer

Mærke: Keystone
Kategori: Klimaanlæg
Model: KSTAW10BE

Har du brug for hjælp?

Hvis du har brug for hjælp til Keystone KSTAW10BE stil et spørgsmål nedenfor, og andre brugere vil svare dig