Klein Tools ET300 Manual

Klein Tools Strømafbryder ET300

Læs gratis den danske manual til Klein Tools ET300 (6 sider) i kategorien Strømafbryder. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Klein Tools ET300, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street

Lincolnshire, IL 60069

1-800-553-4676

www.kleintools.com 139578 Rev. 09/19 D

WARRANTY

www.kleintools.com/warranty

CLEANING

Be sure unit is turned off and wipe with a clean, dry lint-free cloth.

Do not use abrasive cleaners or solvents.

STORAGE

Remove the batteries when instrument is not in use for a prolonged period of

time. Do not expose to high temperatures or humidity. After a period of storage

in extreme conditions exceeding the limits mentioned in the Specifications

section, allow the instrument to return to normal operating conditions before

using it.

DISPOSAL / RECYCLE

Do not place equipment and its accessories in the trash.

Items must be properly disposed of in accordance with local

regulations. Please see www.epa.gov www.erecycle.org or

for additional information.

INSTRUCTION MANUAL

ENGLISH

Digital Circuit Breaker Finder

• FULLY AUTOMATIC

• FLASHING ARROW

INDICATOR FOR

EASY IDENTIFICATION

• 90 – 120V AC

OPERATION

• MICROPROCESSOR

CONTROLLED FOR

MORE ACCURATE

READINGS

ET300

OPERATING INSTRUCTIONS

1. Identify the wall outlet or fixture for which the breaker must

be determined.

2. Safely check that the outlet or fixture is live.

3. Plug in the transmitter. Its LED will light if it is receiving power.

4. Move to the breaker panel with the receiver.

5. Turn on the receiver by pressing, but not holding, the power button.

You will hear a beep and see its LED lit.

6. Position the receiver perpendicularly on the breakers in the panel

with the power button pointing up.

7. Slowly scan all breakers in the panel once. Ignore any beeps

or indications, as the receiver is learning the panel.

8. Scan all breakers a second time. This time, the receiver will beep

and illuminate the green arrow only at the correct breaker.

9. Power off the receiver by pressing and holding the power button.

Return to the outlet or fixture and remove the transmitter.

NOTE: All appliances or equipment on the circuit being tested should be

unplugged to help reduce the possibility of erroneous readings.

OPTIONAL ACCESSORIES

(Cat. No. 69411)

GENERAL SPECIFICATIONS

• 90 – 120V ACOperating Voltage:

• 50 – 60HzOperating Frequency:

• Tracking Distance: Up to 1000 ft. (305 m)

• Operating Temperature: 32°F – 104°F (0°C – 40°C)

• 50%Relative Humidity:

• < 6562 ft. (2000 m)Altitude:

• For indoor use onlyEnvironment:

• 9 volt alkaline batteryPower:

• Approximately 4 minutesAuto Power Off:

• Transmitter Dimensions: 2.8" x 1.9" x 1.2" (7.11 x 4.83 x 3.04 cm)

• 6.0" x 2.0" x 0.9" (15.24 x 5.08 x 2.29 cm)Receiver Dimensions:

• Transmitter Weight: 1.6 oz. (45 g)

• 3.2 oz. (91 g)Receiver Weight:

• Indication at 0.16" (4 mm) distance from a wire Sensitivity:

carrying 120V AC.

• UL listedSafety Rating:

WARNINGS

To ensure safe operation and service of the tester, follow these instructions.

Failure to observe these warnings can result in severe injury or death.

• Understand the risks of working around live voltage.

• Turn off power before inspecting, applying, or removing

the transmitter (when using the optional 'Leads Adapter').

• Exercise extreme caution around live, bare wires, especially

in an open breaker panel.

• Consult with an experienced electrician when necessary.

• Other equipment or devices attached to the circuit being tested could

interfere with the tester. Clear the circuit before testing.

Light Fixture Adapter:

Screw this adapter into an empty light socket.

Make sure the fixture is live. Plug in the

transmitter and follow the instructions

starting at step 4.

Leads Adapter:

Carefully attach leads to the correct wires.

Plug in transmitter to adapter. Follow the

instructions starting at step 4.

Exercise extreme caution around live wires.

Digital Circuit Breaker

Finder

ET300

Micro-Processor

Controlled

When you press

down on the

Power Button

LED will light up

Digital Circuit Breaker

Finder

ET300

ssor

Digital Circuit Breaker

Finder

ET300

TRANSMITTER

Once plugged in, the LED

will light up when

socket is live

Digita l Cir cuit Brea ker

Finder

ET300

TRANSMITTER

ENGLISH

Produkt Specifikationer

Mærke:	Klein Tools
Kategori:	Strømafbryder
Model:	ET300

Har du brug for hjælp?

Hvis du har brug for hjælp til Klein Tools ET300 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Strømafbryder Klein Tools Manualer

Klein Tools ET300 Manual

27 August 2024

Strømafbryder Manualer

Nyeste Strømafbryder Manualer

Schneider ComPact INV1000 Manual

30 December 2025

30 December 2025

30 December 2025

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024

9 December 2024