Klipsch Flexus Wall Mount Manual

Klipsch Ikke kategoriseret Flexus Wall Mount

Læs gratis den danske manual til Klipsch Flexus Wall Mount (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Klipsch Flexus Wall Mount, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

FLEXUS CORE 200

RIGHT-ANGLE BRACKET

FLEXUS CORE 300

RIGHT-ANGLE BRACKET

MOUNTING TEMPLATE HAS 1.0 INCH (25 MM) SPACING AROUND PERIMETER EXCEPT AS NOTED BELOW

1.0 (FLEXUS CORE 300)

6.5 (FLEXUS CORE 200)

Wood Screw

Anchor Screw

Wood Screw

Anchor

USE PROVIDED T20 DRIVE BIT

#2 PHILLIPS SCREWDRIVER NOT INCLUDED

ANCHOR

(TOGGLE SHOWN IN INSTALL ORIENTATION)

USE PROVIDED FLAT WASHER

WITH BOTH WOOD AND

ANCHOR SCREWS

Screws

FLEXUS CORE 200

Mounting Template

MUST USE ONE OF THESE FIVE SLOT OPENINGS

WHEN MARKING SCREW LOCATIONS ON WALL PER EACH SIDE.

FLEXUS CORE 300

MUST USE ONE OF THESE THREE SLOT OPENINGS

WHEN MARKING SCREW LOCATIONS ON WALL PER EACH SIDE.

Wood Screws

Total Screws

Wall Anchor &

Anchor Screw

Pre Drill

See Note 1

3 3

2 2

4 4

Note 1

Note 2

Note 3

See Note 2

Centered

Not

Centered

Not

Centered

16" Stud Wood

Spacing

Keep mounting template against wall. Use a 1/8" (3mm) drill bit and drill through template, drywall, and into stud.

Total pre drill depth 2~2.5 inches.

Mark screw location with sharp object by piercing template. Move folded template below and tape to wall to

help catch drywall debris. Use a #2 Phillips screwdriver, press anchor tip slightly into drywall.Apply pressure,

turn anchor until flush with drywall and arrows on head of anchor point up and down.

24" Stud Wood

Spacing

Concrete, Brick, or Plaster

Use a minimum of 3 fasteners (not included)

Wall mounting template. Don’t discard

during unboxing process.

PREPARE MOUNTING TEMPLATE

ATTACHMENT TO WALL DETAILS

MOUNTING TEMPLATE

Unfold template from its

shipping configuration.

Fold bottom flap and side

flaps along bend lines. Then

tuck triangular flap behind

and insert into vertical slot

opening at each end.

Produkt Specifikationer

Mærke:	Klipsch
Kategori:	Ikke kategoriseret
Model:	Flexus Wall Mount

Har du brug for hjælp?

Hvis du har brug for hjælp til Klipsch Flexus Wall Mount stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Klipsch Manualer

Klipsch Heritage Active Crossover Manual

8 Oktober 2025

Klipsch KI-362-SMA-II Manual

19 Juli 2025

Klipsch Horizon HS-1 Manual

18 Juli 2025

Klipsch Reference RVX-42 Manual

10 Juli 2025

Klipsch Flexus Wall Mount Manual

4 Juli 2025

Klipsch Reference RS-42 Manual

27 Februar 2025

Klipsch Reference RS-52 Manual

27 Februar 2025

Klipsch Reference RC-64 Manual

26 Februar 2025

Klipsch Reference RC-52 Manual

26 Februar 2025

Klipsch IC-500-T-SC Manual

14 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hendi 580035 Manual

3 November 2025

MSW -PTM-02 Manual

3 November 2025

ANCEL FX1000 Manual

3 November 2025

Extron RCP 401 Manual

3 November 2025

IFM E11847 Manual

3 November 2025

Ingenuity Easy Rinse Bather Manual

3 November 2025

ANCEL S2000 Manual

3 November 2025

ANCEL HD3600 Manual

3 November 2025

Hendi 550113 Manual

3 November 2025

Philips Series 5000 MG5942 Manual

3 November 2025