Kurth Electronic POEcheck Manual


Læs nedenfor 📖 manual på dansk for Kurth Electronic POEcheck (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 4 personer og blev bedømt med 5.0 stjerner i gennemsnit af 2.5 brugere

Side 1/2
POEcheck - Bedienungsanleitung
Die aktuell gültige Technologie basiert auf dem IEEE 802.3af Standard.
Er definiert zwei Varianten zur Stromeinspeisung in ein PoE-taugliches Gerät.
Das (Power Sourcing Device), das den Strom in die Netzwerkverkabelung PSE
einspeist, kann entweder ein sein oder ein Endspan-Gerät, die sich Midspan-Gerät
beide entsprechend dem Standard in einer Reihe von Punkten klar unterscheiden.
Von gelieferter Strom wird in Adernpaare eingespeist Endspan-Geräten
die Daten übertragen und wird Typ A genannt, oder er wird in unbenutzte Adernpaare
eingespeist und heisst dann Typ B.
Der von Midspan-Geräten gemäß jetziger Norm gelieferte Strom wird typischerweise in
Stecken Sie das mitgelieferte RJ45 Kabel in den POEcheck und dann in den Datenport.
Als Alternative kann das am Endgerät eingesteckte Datenkabel in den POEcheck
eingesteckt werden. Dann wird auch das Kabel überprüft.
Beachten Sie die LEDs auf dem POEcheck:
LED
Status LED
Information
A-Switch
B-Midspan
Aus
Aus
Keine PoE-Spannung am Datenport oder
Cisco-eigenes System
A-Switch
B-Midspan
Grün
Aus
Spannung erkannt. Sie wird von einem Typ
A-Gerät geliefert, einem Standard 802.3af
Switch
A-Switch
B-Midspan
Aus
Grün
Spannung erkannt. Sie wird von einem Typ
B-Gerät geliefert, einem Standard 802.3af
Midspan Gerät
A-Switch
B-Midspan
Grün
Grün
Spannung erkannt. Sie wird von einem
High Power Gerät geliefert, welches beide
Übertragungswege nutzt
Made in
Germany
Kurth Electronic GmbH | Mühleweg 11 | D 72800 Eningen u. A. GERMANY | Tel. +49(0)7121 9755 0 |
Fax +49(0)7121 9755 56 | info@kurthelectronic.de | www.kurthelectronic.de
POEcheck - How to use
Power over Ethernet regarding the regulation defines a way to build IEEE802.3af
Ethernet power-sourcing equipment and powered terminals.
The specification involves delivering power over shielded or unshielded twisted-pair
wiring. There are two versions - Type A ( Endspan ) where the router or switch
delivers the power over the data pairs.
Or Type B (Midspan) where the power is delivered over the spare pairs. In any
case is managed by a multi-stage handshake protocoll to protect equipment PoE
from damage and to manage power budgets. This features protecting the
equipment but also makes it impossible to check for power with standard
equipment.
Connect the test cable who comes with the uint into the POEcheck and then to the
dataport under test. Or you can use the cable who is connected to the end unit.
In this case the cable is also tested.
Watch the indicator LEDs on the POEcheck:
LED
Status LED
Information
A-Switch
B-Midspan
Off
Off
No POE power detected or CISCO non-
standart switch
A-Switch
B-Midspan
Green
Off
Power detected. Originated from a Type A
unit, an standard 802.3af switch
A-Switch
B-Midspan
Off
Green
Power detected. Originated from a Type B
unit, an standard 802.3af midspan
A-Switch
B-Midspan
Green
Green
Power detected. Originated from a high
power unit who uses both ways.
Made in
Germany
Kurth Electronic GmbH | Mühleweg 11 | D 72800 Eningen u. A. GERMANY | Tel. +49(0)7121 9755 0 |
Fax +49(0)7121 9755 56 | info@kurthelectronic.de | www.kurthelectronic.de


Produkt Specifikationer

Mærke: Kurth Electronic
Kategori: Ikke kategoriseret
Model: POEcheck

Har du brug for hjælp?

Hvis du har brug for hjælp til Kurth Electronic POEcheck stil et spørgsmål nedenfor, og andre brugere vil svare dig