La Crosse Technology 40222B Manual

La Crosse Technology Vækkeur 40222B

Læs gratis den danske manual til La Crosse Technology 40222B (3 sider) i kategorien Vækkeur. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 19 anmeldelser. Har du et spørgsmål om La Crosse Technology 40222B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

AUTO- SET by EQUITY

SETS THE CORRECT TIME WHEN POWERED UP!

MODEL 40222S/40222B

OPERATING MANUAL

POWER REQUIREMENT

One 3v Lithium Battery CR2032 is required to hold the time memory. The lithium battery

is included.

Two “AA” Alkaline batteries are required to operate the time function. These batteries

are not included.

TIME ZONES

H-Hawaii-Aleutian Standard Time

A-Alaska Standard Time

P-Pacic Standard Time

M-Mountain Standard Time

C-Central Standard Time

E-Eastern Standard Time

SETTING PROCEDURE FOR THE AUTO-SET CLOCK

BEFORE inserting the “AA” batteries into the battery compartment

• Make sure that the clock hands are in the 12:00 position

• The Mode switch (8) should be in the SET position

• Slide the time zone switch (2) to the correct time zone

• Slide the DST witch (9) to the appropriate position for your area

• Verify that the rear LCD display (4) reads the correct time

• Once all above is complete, insert the “A” batteries; slide the mode switch (8)

to the run position, the clock will fast forward to the correct time

Note: To change the Time zone, DST, or time, the mode switch (8) must be in SET

position. Remove the “AA” batteries, and then follow the setting steps above.

DAYLIGHT SAVINGS TIME

If you live in an area that does observe DST, place the DST switch into the ON

position. The clock will now adjust automatically each spring and fall to correct for

the 1-hour time change.

If you live in an area that does not observe DST, such as Arizona, Hawaii, or parts of

Indiana, place the switch into the OFF position to deactivate the DST function.

REPLACING 3V LITHIUM BATTERY

The Auto-set time memory is maintained by a lithium button cell battery, model CR2032.

The expected life of this battery is about 8 years. Be sure that the 2 “AA” batteries

in the clock are fresh. The MODE switch (8) must be in the RUN position when replacing

this button cell battery. This battery is located in the small round battery

compartment on the rear of the clock secured by a screw. Open the battery compartment

(3) with a screw driver and replace the CR2032 lithium battery observing the polarity.

Then close the compartment securing with the screw.

SETTING THE CORRECT DATA INFORMATION IN THE LCD DISPLAY

1) Manually turn the clock hands to 12:00

2) Be sure a fresh Lithium button cell battery is in place, model CR2032

3) Slide the time zone switch (2) to the desired time zone position

4) Choose DST on or o, by sliding the DST switch to ON or OFF position

5) Slide the mode switch (8) to SET position, a SETUP icon will be ashing on the

display. The HOUR digit will be also ashing. Press (+) key (6) or (-) key (7) to

adjust to the correct hours. Note the “PM” indicator on the LCD display.

6) Press MODE key (5) once, the minute digit will be ashing. Press (+) key (6) or (-

) key (7) to adjust to the correct minutes.

7) Press MODE key (5) again, to set month, day, year, similarly.

8) Insert two fresh “AA" alkaline batteries into battery compartment (1), according to

the polarity shown.

9) You can slide the switch (8) to SEC position, press (+) key (6) to have the clock’s

second hand move to 12:00 position.

10) Slide the switch (8) to RUN position, the clock’s hands will move quickly, and

automatically synchronize the new time data in the LCD display.

REPLACING THE “AA” BATTERIES

For best performance, replace the “AA” batteries annually to maintain accuracy. With

the MODE switch in the RUN position, remove the old “AA” batteries. Make sure the

hands are in the 12:00 position . If not so, manually turn the hands to 12:00. Insert 2

fresh “AA” alkaline batteries into the battery compartment (1) according to the

polarity shown. The clock will automatically move to the correct time displayed in the

LCD display. Alkaline batteries are recommended. Carbon zinc and rechargeable (nickel

cadmium) batteries are not recommended. Please help in preservation of the environment

and return used batteries to an authorized depot.

Two Year Warranty (U.S.A.)

Equity products are warranted for two years from the date of consumer purchase against defects in material and

Produkt Specifikationer

Mærke:	La Crosse Technology
Kategori:	Vækkeur
Model:	40222B
Bredde:	250 mm
Dybde:	30 mm
Højde:	250 mm
Vægt:	395 g
Produktfarve:	Sort
Ramme, materiale:	Plast
Formfaktor:	Cirkel
Antal understøttede batterier:	3