7
Rev. E 2/09 2085358
2085358
Rev. E 2/09 2
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electrical shock and injury to persons, including the following:
SAVE THESE INSTRUCTIONS
Read all instructions before using this Fan.
1. Make certain the power source conforms to the electrical requirements of the Fan.
2. Make certain that the room is equipped with a working smoke detector.
3. Use this Fan only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock,
or injury to persons.
4. To reduce the risk of personal injury and electric shock, the Fan should not be played with or placed where small children can reach it.
5. Unplug power cord before installing, servicing, or moving the Fan.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING
OR MOVING THE FAN. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG FAN BEFORE
LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE FAN IS ON OR PLUGGED IN.
6. This Fan must be used in potentially dangerous locations such as flammable, explosive, chemical-laden or wet atmospheres NOT
where gasoline, paint or flammable liquids are used or stored.
7. DO NOT use Fan in or near a window. Rain may create an electrical hazard.
8. Completely assemble Fan, according to instructions, before connecting to power supply.
REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK - DO NOT USE THIS FAN
WITH ANY SOLID STATE SPEED CONTROL DEVICES.
9. Where possible, avoid the use of extension cords because the extension cord may overheat and cause a fire. If you must use an exten-
sion cord, minimize the risk of overheating by using the shortest cord possible and ensuring that it is UL listed. use a single NEVER
extension cord to operate more than one Fan. Do not plug Fan into any other cord connected device, such as a power strip, cord
reel, surge protector, multiple outlet adapters or outlet-type air fresheners. The use of such devices may create a fire hazard.
10. operate any Fan with a damaged cord or plug or after the Fan malfunctions, has been dropped or damaged in any manner. NEVER
There are no user serviceable parts. Return Fan to an authorized service facility for examination, electrical or mechanical adjustment
or repair.
11. insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or fire, NEVER
or damage the Fan. To reduce the risk of fire, block or tamper with the Fan in any manner while it is in operation.DO NOT
12. Always place the Fan on a stable, flat, level surface when operating, to avoid the chance of the Fan overturning. Locate the Power
Cord so the Fan or other objects are not resting on it. run Power Cord under carpeting. cover Power Cord with DO NOT DO NOT
throw rugs, runners or the like. Arrange Power Cord away from room traffic and where it will not be tripped over.
13. This Fan is not intended for use in wet or damp locations. locate a Fan where it may fall into a bathtub or other water con-NEVER
tainer. use Fan where flammable liquids are used or stored.NEVER
14. use Fan outdoors. NEVER
15. This Fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please
refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical require-
ments for Agricultural Buildings. THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
16. This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or
local codes or standards relating to electrical requirements for Hazardous locations. THIS FAN DOES NOT MEET THE REQUIRE-
MENTS OF NEC ARTICLE 500 (2008).
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock,
this plug is intended to fit in a polarized outlet only one way. Match wide blade of plug to wide slot. Fully
insert. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. DO NOT attempt to defeat this safety feature.
This plug is a safety feature, to reduce the risk of fire, electric shock and personal injury. DO NOT remove,
replace, repair or tamper with the originally supplied plug. If the Fan does not function properly, it may be due
to the safety device incorporated in this plug. Return to an authorized service center or call 800-233-0268,
Monday - Friday, between 8:00 a.m. and 5:00 p.m. EST. If the plug warning label is missing or damaged, call
the toll free number for a replacement label.
1. Inserte la parte delantera del Asamblaje Del Motor hacia la parte
delantera de la Base. Empuje asi atras en el Asamblaje del Mo-
tor (Figura 1) y acomodelo completamente en su posicion.
4. Asiente la Rejilla Trasera Tuerca De Plástico y sujetela con la
HACIA LA DERECHA. (Figura 4)
5. Deslice la Hélice en el eje del motor. (Alinear la (Figura 5) Ra-
nura Del Cubo de la tapa con el Pasador del eje del motor. Figura
5A)
6. Para asegurar la Helice, enroscarla hasta que quede
apretada en el Cubo de la Tapa haciéndola girar
Hacia la Izuierda.
7. Con el cabezal del ventilador en posición vertical, alinee el Adorno
de la de modo que quede horizontal y con Parrilla Delantera
el lado debido hacia arriba. Empiece en la parte superior de la
parrilla y siga hacia abajo, insertando las Trabas Parrilla de la
Trasera Ranuras Parrilla Delantera (Figura 6) en las de la .
Asamblaje
Del Motor
Base
Figura 1
Figura 5
2. Alinear la lengüeta de la Rejilla Trasera con la ranura en la parte
superior de la cubierta delantera del . Motor (Figura 2)
3. Inclinar la cabeza del ventilador hacia atrás. Coloque la Re-
jilla Trasera en el Motor. (La marca UP indica la parte superior.)
(Figura 3)
Adorno
Figura 6
Trabas
Ranuras
Parrilla
Delantera
Parrilla Trasera
Figura 3
Figura 2
ARMADO
Motor
Rejilla Trasera
Motor
Rejilla Trasera
Figura 4
Tuerca De
Plástico
Rejilla Trasera
Hélice
Figura 5A
Pasador
R a n u r a
Del Cubo
1. Coloque el ventilador sobre una superficie firme y nivelada.
ADVERTENCIA: Los tacos de plástico o hule, tales como las
patas de esta unidad, pueden pegarse a la superficie de los muebles.
La unidad podría dejar un residuo capaz de oscurecer, manchar o
dejar marcas permanentes en el acabado de ciertas superficies de
muebles, incluyendo superficies y pisos de madera.
2. Conecte el cable eléctrico a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchuf es queda n flojos en los
tomacorrientes, pueden deslizarse parcial o
completamente fuera del tomacorriente con un leve
movimiento del cable adosado. Los tomacorrientes
en este estado podrían sobrecalentarse y representar
un grave peligro de incendio; si está cubierto por una
cortina o tela, el riesgo de incendio es aún mayor.
FUNCIONAMIENTO
