Lectrosonics DNTBOB88 Manual

Lectrosonics Processor DNTBOB88

Læs gratis den danske manual til Lectrosonics DNTBOB88 (16 sider) i kategorien Processor. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Lectrosonics DNTBOB88, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/16
DNTBOB 88
8x8 Breakout Box
INSTALLATION AND SETUP GUIDE
Rio Rancho, NM, USA
www.lectrosonics.com
Fill in for your records:
Serial Number:
Purchase Date:
Dante is a trademark of Audinate Pty Ltd.
IMPORTANT:
Set all DNTBOB 88 units to the
Switched mode for initial setup.
See page 7 for details.
DNTBOB88
Tested to comply
with FCC Standards
FOR HOME OR OFFICE USE
ASPEN Digital Processor
LECTROSONICS, INC.
2
FCC Part 15 Compliance
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired op-
eration.
CAUTION: Changes or modifications not expressly
approved by Lectrosonics, Inc. could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation. The
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment
and receiver
• Connect the equipment into an outlet on a circuit
different from that which the receiver is connected
• Consult the dealer or an experienced radio/TV
technician for help
Changes or modifications to this equipment not ex-
pressly approved by Lectrosonics, Inc. could void the
user’s authority to operate it.
Industry Canada
Compliance
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe B est conforme a
la norme NMB-003 du Canada.

Produkt Specifikationer

Mærke: Lectrosonics
Kategori: Processor
Model: DNTBOB88

Har du brug for hjælp?

Hvis du har brug for hjælp til Lectrosonics DNTBOB88 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Processor Lectrosonics Manualer

Lectrosonics

Lectrosonics DNT16i Manual

5 September 2024
Lectrosonics

Lectrosonics DNTBOB88 Manual

2 September 2024
Lectrosonics

Lectrosonics DNT0212 Manual

2 September 2024

Processor Manualer

Nyeste Processor Manualer

Roland

Roland VSR-880 Manual

1 Juni 2025
Allen & Heath

Allen & Heath AHM-32 Manual

25 Februar 2025
Kopul

Kopul DAN-2X2UAC Manual

4 Februar 2025
Kopul

Kopul DAN-AIXF2 Manual

4 Februar 2025
Kopul

Kopul DAN-AOXM2 Manual

4 Februar 2025
Alto

Alto ACL2 Manual

30 Januar 2025
Alto

Alto ALPHA MICtube Manual

30 Januar 2025
Alto

Alto DIGAN 2.7 Manual

30 Januar 2025
Alto

Alto DIGAN 2.30 Manual

30 Januar 2025
Alto

Alto Monitor Manual

30 Januar 2025