Lectrosonics LMb/X Manual

Lectrosonics Ikke kategoriseret LMb/X

Læs gratis den danske manual til Lectrosonics LMb/X (24 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Lectrosonics LMb/X, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/24

LMb

Digital Hybrid Wireless® UHF Belt Pack Transmitter

Featuring

Digital Hybrid

Wireless®

INSTRUCTION MANUAL

Rio Rancho, NM, USA

www.lectrosonics.com

Fill in for your records:

Serial Number:

Purchase Date:

Quick Start Steps

1) Install good batteries and turn power on (see

pages 5 and 6).

2) Set compatibility mode to match the receiver (see

page 9).

3) Connect signal source and adjust input gain for

optimum modulation level (see page 9).

4) Set StepSize and frequency to match receiver

(see page 10). Also see receiver manual for scan-

ning procedure.

5) Turn on the receiver and verify RF and audio

signals are present (see receiver manual).

LMb, LMb/E01, LMb/E06, LMb/X

WARNING: Moisture, including talent’s sweat,

will damage the transmitter. Wrap the LMb in

a plastic baggie or other protection to avoid

damage or see LMCVR.

LMb, LMb/E01, LMb/E06, Lmb/X

LECTROSONICS, INC.

Table of Contents

Quick Start Steps 1 .................................................................................................................................................................................

Introduction 3 .............................................................................................................................................................................................

About Digital Hybrid Wireless 3 .............................................................................................................................................................

Frequency Agility 3 .................................................................................................................................................................................

Servo Bias Input and Wiring 3 ................................................................................................................................................................

DSP-controlled Input Limiter 3 ...............................................................................................................................................................

LMb Block Diagram 4 .............................................................................................................................................................................

No Pre-Emphasis/De-Emphasis 4 .........................................................................................................................................................

Pilot Tone Squelch 4 ...............................................................................................................................................................................

Battery Installation 5 .................................................................................................................................................................................

Belt Clips 5 .................................................................................................................................................................................................

Operating Instructions 6 ...........................................................................................................................................................................

Battery Status LED Indicators 6 .............................................................................................................................................................

Powering On in Operating Mode 6 .........................................................................................................................................................

Powering On in Standby Mode 7 ...........................................................................................................................................................

Powering Off 7 ........................................................................................................................................................................................

Navigating Menus 7 ................................................................................................................................................................................

Locking/Unlocking Changes to Settings 7 ............................................................................................................................................

Power Menu Options 7 ...........................................................................................................................................................................

Selecting Programmable Switch Functions 8 .......................................................................................................................................

Main Window Indicators 8 ......................................................................................................................................................................

Selecting the Compatibility (Compat) Mode 9 ......................................................................................................................................

Connecting the Signal Source 9 .............................................................................................................................................................

Adjusting the Input Gain 9 ......................................................................................................................................................................

Selecting Step Size 9 ..............................................................................................................................................................................

Selecting Frequency 10 ..........................................................................................................................................................................

Selecting Frequency Using Two Buttons 10 ..........................................................................................................................................

Helpful Features on Receivers 10 ..........................................................................................................................................................

About Overlapping Frequency Bands 10 ...............................................................................................................................................

Selecting Audio Polarity (Phase) 11 .......................................................................................................................................................

Adjusting LCD Backlight 11 ...................................................................................................................................................................

RF ON/OFF on the Menu 11 ...................................................................................................................................................................

Selecting Battery Type 11 .......................................................................................................................................................................

Restoring Default Settings 11 ................................................................................................................................................................

IR (infrared) Sync 11 ...............................................................................................................................................................................

5-Pin Input Jack Wiring 12 ........................................................................................................................................................................

Microphone Cable Terminationfor Non-Lectrosonics Microphones 13 ...............................................................................................

Input Jack Wiring for Dierent Sources 14 .............................................................................................................................................

Microphone RF Bypassing 15 ................................................................................................................................................................

Line Level Signals 15 ..............................................................................................................................................................................

Wiring Diagram for MI39A Instrument Cable 15 ....................................................................................................................................

Supplied and Optional Accessories 16 ....................................................................................................................................................

Troubleshooting 17 ....................................................................................................................................................................................

Specications and Features 18 ................................................................................................................................................................

Service and Repair 19 ...............................................................................................................................................................................

Returning Units for Repair 19 .................................................................................................................................................................

Consumer Alert for US Users - FCC Order DA 10-92

Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this

microphone system without a license is subject to certain restrictions: the system may not cause harmful

interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has no protection from

interference received from any other device. Purchasers should also be aware that the FCC is currently evaluat-

ing use of wireless microphone systems, and these rules are subject to change. For more information, call the

FCC at 1-888- CALL-FCC (TTY: 1-888-TELL-FCC) or visit the FCC’s wireless microphone website at www.fcc.

gov/cgb/wirelessmicrophones. To operate wireless microphone systems at power greater than 50mW, you

must qualify as a Part 74 user and be licensed. If you qualify and wish to apply for a license go to: http://www.

fcc.gov/Forms/Form601/601.html