Legrand CS102 Manual

Legrand Netværkskort/adapter CS102

Læs nedenfor 📖 manual på dansk for Legrand CS102 (61 sider) i kategorien Netværkskort/adapter. Denne guide var nyttig for 63 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/61

CS102 SNMP Card

User Manual

User’s Manual

Version 0.94

July, 2023

CS102 SNMP Card

User Manual

Chapter 1 - Introduction

CS102 can manage UPS systems using their native serial protocols. User can use web browser or

any NMS, SNMP, or MODBUS manager to manage UPS via Ethernet.

The CS102 also provides shutdown schedules for different operating systems: for example, it can

send a shutdown command in the event of a scheduled shutdown, utility power failure, UPS low

battery condition, UPS overload, UPS overtemperature, and other alarms. All extinguishing events

are user configurable. The shutdown software will perform an orderly automatic shutdown to

avoid crashing clients or servers.

1.1. Features

◼ Real-time UPS health monitoring

◼ Comprehensive UPS management and flexible configuration via Web Browser, NMS, Telnet,

and SNMP.

◼ Automatic events notification via E-mail, and SNMP Trap.

◼ Graceful shutdown to protect up to 250 servers/workstations from data loss due to power

outa . ge

◼ Assigned IP automatically via DHCP or BOO . TP

◼ Scheduling shutdown/startup/reboot of UPS via remote control.

◼ Regularly records UPS parameters for statistical analysis and event diagnosti . cs

◼ Support for standard UPS MIB (RFC1628).

◼ Auto-sense to works in the 10/100Mbps fast Ethernet network environme . nt

◼ WOL function supported.

◼ Configuration utility simplifies the firmware upgrade proce . ss

◼ Support Radius and NTLM . V1

◼ IPv4 and IPv6 dual ck. sta

CS102 SNMP Card

User Manual

1.2. CS102 System Application

The following diagram shows how the CS102 SNMP Web Card which can be used in a network

application. supports various kinds of protocol such as HTTP, SNMP, MODBUS, c It et …

Through the SNMP NMS and Web Browser, user can obtain the UPS status, issue commands of

UPS and set up CS102 configuration via the network.

CS102 also provides shutdown software for sending the event notifications to the connected tool

clients. The shutdown software can be installed on various operating systems. It can

communicate with the CS102 automatically via a proprietary protocol. CS102 will issue the

shutdown command to shutdown software in the event of AC failure, battery low and scheduled

shutdown. Shutdown software will proceed to the shutdown process to prevent the abnormal

shutoff of host or server.

CS102 SNMP Card

User Manual

Step3. address to the same network Select the device and then click “Set IP” to change the IP

segment as your LAN.

Step4. Type in Account and Password . The default administrator and click on “Next” button

account is:

Account: admin

Password: cs102snmp

CS102 SNMP Card

User Manual

2. Enter the appropriate date and time information in the specified format and click to “Apply”

save the settings.

3.4. Network Protocols

By default, only strictly necessary network protocols are enabled.

Select “Network Protocols” from the main menu to enable the required additional network →

protocols In case you are not sure what to enable, please leave the default. .

3.5. Network Configuration

1. from the main menu: Select “Network →Network settings”

2. Enter the required information: IP address, Gateway, Subnet Mask, DNS

CS102 SNMP Card

User Manual

Chapter 4 - Web Interface

4.1. System Status

In this section you can check the real time operating status of the UPS, Schedule, Alarm and other s,

product information.

4.1.1. Dashboard

In the dashboard, you can check the operational status, scheduling, and other data of the UPS.

This page updates automatically.

Section

Description

Power Flow Diagram

This area displays the input/output power status of the UPS in a

diagram. The most important is the "UPS status" light at the

bottom left: if it turns yellow or red, check the "Active Alarm list ".

Voltage Real time Chart

This chart displays the input/output voltages of the UPS in real-time

in graph format

Battery Real time Status

◼ Battery Capacity displays the estimated charge level of the UPS :

batteries.

◼ Autonomy Time displays the estimated remaining back-up time :

of the UPS. For some UPSs this data is not available.

◼ Temperature: displays the internal temperature of the UPS.

History Log of Output

Load

This chart displays the power consumption of the devices

connected to the UPS as percentages.

Schedule Calendar

UPS schedules can be checked for each month.

Active Alarm List

This table displays the currently active alarm s.

CS102 SNMP Card

User Manual

Identification

UPS Identification

Item

Description

UPS Model

The UPS model name (e.g., “Daker DK Plus 3000”)

UPS Name

The unique name of the UPS, as configured by the Administrator

(default is the same as displayed in "UPS Model")

UPS Serial Number

The serial number of the UPS

UPS Firmware Revision

The firmware version of the UPS

CS102 Firmware Revision

The firmware version of the CS102 SNMP card

UPS Type

Type of -Line Off-Line Line-Interactive , the UPS: “On ”, “ ”, “ ”

“ ” or “Three phase in One Out”3 Phase -

UPS Protocol

This allows the user to choose the model/family of the UPS

connected to the CS102

UPS Baud Rate

It allows to select the communication parameters between the

CS102 and the UPS. Except in very special cases, leave the default

setting (“Auto Detect”)

Rating Group

Item

Description

Input Rating Voltage

The nominal input voltage (P-N) of the UPS, in Volts

Input Frequency

The nominal input frequency of the UPS, in Hertz

Output Rating Voltage

The nominal output voltage (P-N) of the UPS, in Volts

Output Frequency

The nominal output frequency of the UPS, in Hertz

Output Rating Current

The nominal output current of the UPS, in Ampere

Rating Battery Voltage

The total nominal voltage of the UPS battery, in Volts

Output Rating VA

The nominal apparent output power of the UPS, in VA

Output Rating Watt

The nominal active output power of the UPS, in Watt

UPS Control

This section let you perform control such as stopping/starting the UPS and running a battery test.

Item

Description

UPS Shutdown Delay

The delay (in seconds) that the UPS stays on after being told to shut

down; it will be added to any shutdown schedule you set.

To avoid improper shutdown of computers, this time should always

be greater than the time required for the computers to shut down

properly

UPS Sleep Time

The duration (in minutes) that the UPS remains in sleep mode.

During this mode, the UPS does not provide output power

regardless of the status of the input line. After the specified time,

the output power will resume.

CS102 SNMP Card

User Manual

Buttons

Item

Description

Reset To Default

To reset the CS102 configuration to the factory default.

Reboot

Restart the CS102. It has no effect on the UPS.

Apply

To save the changes made in this page

Upload and Download

Item

Description

Download Root Certificate

To download the current certificate of the CS102

Download Configurations

Allows to create a backup file of the current CS102 configuration.

Upload Configurations

Allows to restore a configuration previously saved using

“Download Configurations” button

Upload CA file

To upload and use a custom certificate file.

CS102 SNMP Card

User Manual

4.3.3 Web Settings .

Web Settings

This page lets you configure the settings related to the Web monitor refresh interval and timeout

when you log in.

Item

Description

Web Refresh Time

The refresh interval (in seconds) of web pages.

Logs per page

Set the number of lines displayed on each log pages

"CS102 Event Log", "UPS Event Log", "History Log" (UPS Management

→ Alerts & Logs)

Web Timeout Interval

It specifies the time interval (in seconds), to log out the user if the user

has no action on the web page.

External Links Setup

This page describes setting up links to web pages and/or external websites. For example, another

UPS or the technical support home page. Up to four links can be set.

Item

Description

Screen Text

The description of the link name that will be displayed in the menu structure,

within the "External Links" menu.

Link Address

The real name of web page to be connected, in URL format.

Status

This field controls the visibility of the link on menu tree. Setting "Disable" will

make this link invisible from menu tree.

CS102 SNMP Card

User Manual

4.4.3 WakeOnLAN .

The Wake On LAN ("WOL") feature can turn on a PC or compatible device, via its MAC address.

After the clients shut down due to UPS shutdown events and after the shutdown events return to

normal, the WOL packet will be sent to the client to restart the PC.

Up to 24 client MAC addresses can be set.

Setting

Item

Description

Repeating Times

The repeat times of sending WOL packet to client. Range 1~99. :

Interval Timer

The time interval (in seconds) between two actions of sending the WOL

packet to the client. Range: 1~999 seconds.

WOL Table

Item

Description

Test

If this option is selected, the WOL packet will send to client to start up PC after

pressing the OL Test " button. "W

MAC Address

Enter the MAC address of the device you want to boot using a WOL packet.

Control

Enable, or disable, the WOL function.

Description

User description. The maximum length of the string is 31 characters.

CS102 SNMP Card

User Manual

Chapter 5 - Configuring the CS102 via SSH

The SSH protocol allows you to access the configuration of the CS102 without using the web

interface. For security reasons, the SSH protocol is disabled by default; you can enable it here:

[Network] [Protocols] [SSH Connection] → →

5.1. Login

Use SSH software (like PuTTY ) to connect to the CS102. When the following message appears “ ”

on the screen, enter your username and password:

admin@192.168.53.23's password: *****

The CS102 Configuration Utility main menu will then be displayed.

5.2. CS102 s etup

From the main menu, digit page: “ ” to enter the 1 SNMP/WEB Card Settings

============================================================

CS102 Configuration Utility

[CS102 Legrand v0.90 a7]

============================================================

1. SNMP/WEB Card Settings

2. Reset Accounts/Passwords to Default

3. Reset Configuration to Default

4. Restart SNMP/WEB Card

0. Exit

Please Enter Your Choice => 1

Produkt Specifikationer

Mærke:	Legrand
Kategori:	Netværkskort/adapter
Model:	CS102
Bredde:	68 mm
Dybde:	133 mm
Højde:	43 mm
Vægt:	69 g
Produktfarve:	Grå
Opbevaringstemperatur (T-T):	0 - 60 °C
Relativ luftfugtighed ved drift (H-H):	20 - 95 %
Ethernet LAN-porte (RJ-45):	2
Ethernet LAN:	Ja
Strømforbrug (typisk):	3 W
Driftstemperatur (T-T):	0 - 40 °C
Hurtig installationsvejledning:	Ja
Forbindelsesteknologi:	Ledningsført
Understøttede netværksprotokoller:	IPv4, IPv6, DHCP, DNS, HTTP, HTTPS, SSH, NTP, SMTP, SNMP, MODBUS TCP, Wake on LAN, UPnP, RADIUS
LED-indikatorer:	Fejl
Udgangsspænding:	5.5 - 40 V
Antal USB-porte:	2
Processorfrekvens:	180 MHz
Understøttede Windows-operativsystemer:	Ja
Understøttede Linux-operativsystemer:	Ja
Grænseflade:	Ethernet
Intern:	Ja
Maksimal dataoverførselshastighed:	1000 Mbit/s
Flashhukommelse:	8 MB
Ethernet-grænsefladetype:	Gigabit Ethernet
Komponent til:	Nødstrømsforsyning (UPS)
Monteringsbeslag inkluderet:	Ja
Processor arkitektur:	ARM9
Wake-on-LAN klar:	Ja