Lexmark T522 Manual

Lexmark Printer T522

Læs gratis den danske manual til Lexmark T522 (2 sider) i kategorien Printer. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Lexmark T522, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Quick Reference

Lexmark Laser Printer

Operator panel

Press Menu to:

• Enter the menus from the ready state

• Scroll through menus or values

• Increase or decrease a numerical value

• Display the Job Menu while the printer is busy

Press Select to:

• Select the item on the second line of the display

• Save the selection as a new default setting

Press Return to:

• Return to the previous menu level

Press Go to:

• Exit printer menus and return to the Ready state

• Clear messages

Press Stop to:

• Temporarily stop all print activity without losing

data

Loading a paper tray

Complete these instructions to load print materials into any of the standard or

optional trays. All paper trays are loaded the same way.

1 Remove the paper tray.

2 Pull the width guide tab and slide the width guide to the far right side of

the tray.

3 Squeeze the length guide lever and slide the length guide to the correct

position for the size paper you are loading.

4 Place the paper into the paper tray with the recommended print side face

down for single-sided printing and face up for double-sided printing. Do

not fill paper above the paper capacity mark (fill line).

Pull the width guide tab and slide the width guide to the left until it lightly rests

against the edge of the paper stack.

Loading the multipurpose feeder

1 Push the lower release latch.

2 Pull the metal bar out far enough to support your paper size.

3 Slide the paper width guide to the far right.

Supported print material sizes and types

Types:

Sizes:

Loading letterhead

Letterhead must be loaded differently depending on whether you want your print

job to be single-sided or double-sided (duplexed).

Ready

1 Menu 2Select 3Return 4

Go 5Stop 6

Pull here

Length

guide

Paper size

indicators

Width

guide

Length guide

lever

Paper and transparencies Envelopes

Plain Paper Labels Preprinted Envelope

Card Stock Bond Colored Paper

Transparency Letterhead Custom Type <x>

Letter A4 B4 Folio* 9 Envelope

Legal A5 JIS-B5 Statement* DL Envelope

Executive B5 Envelope

C5 Envelope

7 3/4 Envelope

10 Envelope

Other Envelope

*This size is not available until Size Sensing is turned off. For more information, refer to

the online information.

In a paper tray

In the multipurpose

feeder

Single-sided printing

Double-sided

(duplex) printing

Printed in USA

This document is printed on recycled paper. 5/01

E.C. 2H0003 P/N 09H0412

Operator panel menus Accessing paper jam areas

You open doors and covers, remove paper trays, and remove options to access paper jam areas. If your

printer has a multipurpose feeder, it is visible when the lower front door is opened. The illustration shows the

location of paper sources and possible paper jam areas.

Warning: Do not attempt to clear any paper jam using tools or instruments. This may permanently

damage the printer.

Print quality problems

PCL Emul Menu

Font Source

Font Name

Point Size

Pitch

Symbol Set

Orientation

Lines per Page

A4 Width

Tray Renumber

Auto CR after LF

Auto LF after CR

Paper Menu

Paper Source

Paper Size

Paper Type

Custom Types

Universal Setup

Substitute Size

Configure MP

Envelope Enhance

Paper Texture

Paper Weight

Paper Loading

Finishing Menu

Duplex

Duplex Bind

Copies

Blank Pages

Collation

Separator Sheets

Separator Source

Multipage Print

Multipage Order

Multipage View

Multipage Border

Quality Menu

Print Resolution

Toner Darkness

PQET

PictureGrade

Job Menu

Confidential Job

Held Jobs

Cancel Job

Reset Printer

Print Buffer

Utilities Menu

Print Menus

Print Net <x> Setup

Print Fonts

Print Directory

Factory Defaults

Format Flash

Defragment Flash

Format Disk

Job Acct Stat

Hex Trace

Setup Menu

Printer Language

Power Saver

Resource Save

Download Target

Print Timeout

Wait Timeout

Auto Continue

Jam Recovery

Page Protect

Display Language

Alarm Control

Toner Alarm

Job Accounting

PostScript Menu

Print PS Error

Font Priority

Serial Menu

PCL SmartSwitch

PS SmartSwitch

NPA Mode

Serial Buffer

Job Buffering

RS-232/RS-422

RS-422 Polarity

Serial Protocol

Robust XON

Baud

Data Bits

Parity

Honor DSR

Network Menu

PCL SmartSwitch

PS SmartSwitch

NPA Mode

Network Buffer

Job Buffering

Network <x> Setup

Mac Binary PS

LocalTalk Menu

LocalTalk Port

PCL SmartSwitch

PS SmartSwitch

NPA Mode

LocalTalk Buffer

Job Buffering

NPA Hosts

LocalTalk Name

LocalTalk Addr

LocalTalk Zone

USB Menu

PCL SmartSwitch

PS SmartSwitch

NPA Mode

USB Buffer

Job Buffering

Mac Binary PS

Parallel Menu

PCL SmartSwitch

PS SmartSwitch

NPA Mode

Parallel Buffer

Job Buffering

Advanced Status

Protocol

Honor Init

Parallel Mode 1

Parallel Mode 2

Infrared Menu

Infrared Port

PCL SmartSwitch

PS SmartSwitch

NPA Mode

Infrared Buffer

Job Buffering

Window Size

Transmit Delay

Max Baud Rate

202 Paper Jam

Printer rear door

230 Paper Jam

Duplex rear door

200 Paper Jam

201 Paper Jam

Upper front door

250 Paper Jam

Lower front door

(down when envelope

feeder is installed)

24x Paper Jam

Integrated input tray

230 Paper Jam

Duplex front

access cover

24x Paper Jam

Paper trays

260 Paper Jam

Envelope feeder

Problem Action

Print is too light. • The toner may be low. To utilize the remaining toner, remove the

cartridge by gripping the handles with both hands. With the cartridge

arrows pointing downward, shake the print cartridge back and forth.

Reinstall the cartridge and then press Go.

• Change the Toner Darkness setting in the Quality Menu.

• If you are printing on an uneven print surface, change the Paper

Weight and Paper Texture settings in the Paper Menu.

Verify that the correct print material is being used.

Toner fog or background shading

appears on the page.

• Check the print cartridge to make sure it is installed correctly.

• Change the print cartridge.

• If the problem continues, change the charge roll.

Streaks appear on the page. • The toner may be low. To utilize the remaining toner, remove the

cartridge by gripping the handles with both hands, and then shake the

print cartridge vigorously. Reinstall the same print cartridge.

• If you are using preprinted forms, make sure the ink can withstand

temperatures of 212°C (414°F).

The job prints, but the top and side

margins are incorrect.

• Make sure the Paper Size setting in the Paper Menu is correct.

• Make sure the margins are set correctly in your software application.

Produkt Specifikationer

Mærke:	Lexmark
Kategori:	Printer
Model:	T522
Vægt:	20411.7 g
Udskrivningsteknologi:	Laser
Maksimal opløsning:	1200 x 1200 dpi
Udskrivningshastighed (sort, normal kvalitet, A4/amerikansk papirformat):	25 sider pr. minut
Medietyper til papirbakke:	Bond paper, Envelopes, Labels, Plain paper, Transparencies
Ikke-ISO udskriftsmedier størrelse:	Executive (184 x 267mm), Folio (media size), Letter (media size), Statement (140 x 216mm), Legal (media size)
Samlet inputkapacitet:	600 ark
Intern hukommelse:	16 MB
Dimensioner (BxDxH):	419.100 x 513.080 x 378.460 mm
Duplex udskrivning:	Ja
Maksimal indgangskapacitet:	4100 ark
Mac kompabilitet:	Ja
Kompatible operativsystemer:	Mac OS 8.6 - 9.x\nApple Mac OS X
Processormodel:	250 MHz
Farve:	Ingen
Lydtryksniveau (udskrivning):	51 dB
Tid til første side (sort, normal):	9 sek./side
Maksimal kapacitetsydelse:	250 ark
Universal-magasin kapacitet:	100 ark
Multifunktionsbakke:	Ja
Netværk klar:	Ja
Lydeffektniveau (standby):	30 dB