LG LW345 Manual

LG Ikke kategoriseret LW345

Læs gratis den danske manual til LG LW345 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 6 anmeldelser. Har du et spørgsmål om LG LW345, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Power-down the system and physically remove the power

cord(s) from the system.

Remove the cover from the system’s chassis, following

instructions provided by the manufacturer.

Select an available PCIe Gen 1 / Gen 2 (x2, x4, p1-x8 or x16)

slot and insert the Velocity Duo card into the slot, as shown

in Figure 1. ( p1-x2 slots are very rare in desktop NOTE:

systems, typical installation will use a p1-x4 slot).

Hold the Velocity Duo card at the edges and press down

gently into place.

Secure the Velocity Duo metal bracket to the system

chassis by tightening the slot screw.

After the Velocity Duo is installed, replace the chassis

cover, reconnect the power cord(s) and boot the computer.

Follow the directions below to complete your upgrade.

Installing the Velocity Duo

in your desktop computer

Velocity Duo Quick Start Guide

To prevent ESD

(Electrostatic Discharge) damage

Use an ESD wrist strap or discharge static electricity by

touching a grounded bare metal surface before handling,

installing, and removing the Velocity Duo. Observe proper

ESD grounding techniques. Store your HDD or SSD in an

anti-static bag until you are ready to install it in the system.

When installing and removing the Velocity Duo Card hold by

the edge of the printed circuit board (PCB), and avoid

touching components including connectors.

IMPORTANT HANDLING INFORMATION

Connecting your SSD to the Velocity DUO Card

Slide both of your

SSDs onto the SATA

connectors on the

Velocity Duo Card. Use

4 mounting screws in

each drive to secure

them to the Duo Card.

SATA connector

Figure 1. Installing the Velocity Duo on

PCIe Gen 1 / Gen 2 slot

NOTE: Windows XP users and those using the Velocity

Duo with a boot disk (i.e. with OS already installed)

Before connecting your SSD to the Velocity Duo, please refer

to the directions below for installation of Windows drivers.

PCIe Gen 1/Gen 2 ( x2 slot or larger)

To ensure optimal RAID  functionality, both of the SSDs on the Velocity Duo must be identical (same brand, same

firmware revision and capacity) Additionally, prior to data cloning, each drive must be eroed out using a disk utility such

as Gparted, Parted agic, or a utility native to your OS. Since RAID  is strictly a performance-enhancing array with data

being striped across 2 drives, if one of those drives should fail, all data on both will be lost. When using Velocity Duo with

RAID  configuration, regular backup is recommended to minimie data loss.

Apricorn’s Technical Support Specialists are available

8.00am to 5.00pm, PST Monday through Friday

Email our Technical Support Department at

support@apricorn.com or call 800-458-5448 option 3

Free Tech Support

Need help? Download product manuals,

checkout FAQs and set up questions at

www.apricorn.com

Changing the boot drive on your PC

Once you have cloned your system to your Velocity Duo drive, you have two options.

Remove your original drive, thereby forcing your system to boot from the Velocity Duo drive.

Go into your system’s BIOS and change your boot order to the Velocity Duo drive, keeping your original drive for storage.

Entering your computer’s BIOS to change the boot order is dependent on your particular system. For directions that apply to your particular

system, please refer to your computer’s product manual.

Note: Do not turn your computer off or allow your computer to sleep during the cloning process. Let the process continue until you

see the congratulations screen. When the congratulations screen appears, select “Quit EZ Gig” and then turn off your computer.

Apricorn’s innovative EZ Gig allows you to clone your entire hard drive or deselect data files from the cloning process to save space, giving

you the option to run your OS and applications from a fast, smaller SSD boot drive, while keeping your documents and media files on your

original hard drive. As EZ Gig is able to run from inside the Windows operating system, simply download EZ Gig from Apricorn’s website

(apricorn.com/products/software/ezgig.html) and run the program. The EZ Gig wizard will guide you through the cloning process in a few

simple steps.

Cloning your hard drive using

Apricorn’s EZ Gig for Windows

For complete instructions go to Apricorn’s

website to download the Velocity Duo manual.

After downloading EZ Gig from Apricorn’s site, open the

EZ Gig program or double click on the EZ Gig icon to get

started. Click “Run EZ Gig” from the EZ Gig Start-up

Options window.

Select “Let’s Get Started” from the EZ Gig main screen.

EZ Gig will then scan for connected drives.

Note: The Velocity Duo card must be installed for EZ Gig to

run. EZ Gig will only run with Apricorn Upgrade devices.

The EZ Gig Wizard will then ask you to choose your Source

drive and your Destination drive. Choose your internal drive

as the Source and the Velocity Duo drive as your

Destination drive.

Once the Source and Destination drives are selected,

EZ Gig will give you the option of cloning your entire system

or deselecting data files from the cloning process to save

space. Make your selection then click “Start Clone.”

Once the clone is complete, you can boot your computer

from the new drive. Please refer to the directions below.

Cloning your hard drive using Apple’s Built-in Disk Utility

Starting in Mac OSX 10.4 it is possible to use the Disk Utility application to perform a Restore operation of the Boot disk to another disk.

Starting in OSX 10.7 this operation needs to be performed while booted in Recovery mode, but the process is still the same. Open Disk Utility

from Applications / Utilities / Disk Utility. Select the Restore tab located at the top of the application window. Carefully drag your original boot

volume to the Source field, and then drag the new SSD mounted to the Velocity Duo to the Destination field. Click the Restore button and the

process will begin. Once the process has finished you will quit the Disk Utility application, and open the System Preferences. Use the Startup

Disk preference pane to choose your new Velocity Duo as the startup disk. Reboot the Mac and the OS will start from the new disk.

Installation of drivers and initial setup of the Velocity Duo

If the Velocity Duo drive is not detected, check the drive connections and ensure that the Velocity Duo is installed correctly in the PCIe slot.

Windows - Before booting any version of Windows from the Velocity Duo, Windows must detect and install drivers for the new

storage controller. If you installed new blank SSDs on the Velocity Duo (directions above) AND are running Windows 7 or Vista,

drivers will be automatically installed. If you are installing a boot drive (i.e. with OS already installed) to the Velocity Duo or are

running Windows XP, please ensure that Windows is booted one time with the Velocity Duo card installed in the computer but

without the SSDs connected. After the drivers are installed, the SSDs may be attached to the Velocity Duo.

Windows XP owners need to download drivers from www.apricorn.com/downloads/VelDuo_drivers.zip

Windows Vista and 7 will automatically detect and install the drivers from Windows Update.

Mac - Hardware support for the Velocity Duo product family is built into the Mac OSX, so no driver install is necessary.

Mac OSX can be booted from any drive attached to the Velocity Duo.

PC CLONING SOFTWARE DOWNLOAD

Apricorn EZ Gig Software for the Velocity Duo

www.apricorn.com/products/software/ezgig.html

Produkt Specifikationer

Mærke:	LG
Kategori:	Ikke kategoriseret
Model:	LW345

Har du brug for hjælp?

Hvis du har brug for hjælp til LG LW345 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LG Manualer

21 Juli 2025

20 Juli 2025

20 Juli 2025

20 Juli 2025

19 Juli 2025

17 Juli 2025

15 Juli 2025

8 Juli 2025

8 Juli 2025

6 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman MY500XT Manual

1 August 2025

Navman FOCUS150 GPS Manual

1 August 2025

Scheppach TW1000 Manual

1 August 2025

Navman MiVue 750 WIFI Manual

1 August 2025

Navman MiVue Drive FHD Manual

1 August 2025

Midea MEC64 Manual

1 August 2025

Navman MY50T Manual

1 August 2025

Navman M100 Manual

1 August 2025

Navman MiVue 770 SAFETY Manual

1 August 2025

Navman MiVue 790 Manual

1 August 2025