Liberty Pumps 405HV Manual

Liberty Pumps Pumpe 405HV

Læs gratis den danske manual til Liberty Pumps 405HV (15 sider) i kategorien Pumpe. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Liberty Pumps 405HV, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/15

IMPORTANT:

Prior to installation, record Model, Serial Number, and

Code Number from pump nameplate for future reference.

MODEL ________________________

SERIAL ______________________

CODE ______________________

INSTALLATION

DATE _____________________ __

7000 Apple Tree Avenue

Bergen, NY 14416

Phone: (800) 543-2550

Fax: (585) 494-1839

www.libertypumps.com

Contents

1.) General Information and Safety

Guidelines

2.) Installation

3.) Maintenance and Troubleshooting

Installation Manual 7212000D

Model 404 and 405 Automatic Drain Pump

MODEL 404 Residential

115 volt

MODEL 405 Commercial 115 volt

MODEL 405HV Commercial 230 volt

Contains Certified pump

Side view

404

Side view

405

Top view

404 and 405

Dimensions are rounded to the nearest 1/8”

Before installation, read the following instructions carefully. Each Liberty pump is individually factory tested to insure proper

performance. Closely following these instructions will eliminate potential operating problems, assuring years of trouble-free service.

 Risk of electric shock. Always disconnect the pump from the power source before handling or making adjustments.

 The electrical connections and wiring for a pump installation should only be made by qualified personnel.

 Explosion hazard during installation. PVC cleaners, primers, and cements can release explosive vapors. These heavier than

air vapors can accumulate in the tank. The heat of soldering or sweating copper or other metal pipe can ignite these vapors

causing a violent explosion. If the unit is to be connected to copper discharge or vent piping, all solvent welded PVC joints must be

allowed to cure a minimum of 24 hours. The access cover must be removed to allow the tank to be thoroughly ventilated prior to

sweating copper pipe near the unit.

 This pump is supplied with a grounding conductor and grounding-type attachment plug. To reduce the risk of electric shock, be

certain that it is connected to a Ground Fault Circuit Interrupter (GFCI) receptacle that meets the latest requirements per UL 943

including End of Life Provision and protection from Reverse Line-Load Miswire.

 Always wear rubber boots when water is on the floor and you must unplug the pump.

 DO NOT bypass grounding wires or remove ground prong from attachment plugs. DO NOT use an extension cord.

 This pump requires a separate, properly fused and grounded branch circuit. Make sure the power source is properly sized for the

voltage and amperage requirements of the pump, as noted on the nameplate.

 The electrical outlet shall be within the length limitations of the pump power cord, and at least 4 feet above floor level to minimize

possible hazards from flood conditions.

 The installation must be in accordance with the National Electric Code, Uniform Plumbing Code, International Plumbing Code, as

well as all applicable local codes and ordinances.

 Keep clear of suction and discharge openings. To prevent injury, never insert fingers into pump while it is plugged in.

 DO NOT use this product for flammable or corrosive liquid.

 DO NOT use this product in applications where human contact with the pumped fluid is common (such as swimming pools,

fountains, etc.)

 NEVER dispose of materials such as paint thinner or other chemicals down drains, as they can chemically attack and damage

pump components, potentially causing product malfunction or failure.

 Model 404 Do not use this pump in water over 140





 Model 405 Do not use these pumps in water over 180°F

 DO NOT DO NOT use pumps in mud, sand, cement, oil or chemicals.

 DO NOT modify the pump in any way.

 DO NOT lift or carry pump by power cord.

 DO NOT remove any tags from pump or cords.

 If pump is installed during construction before power is available, it

must be protected from the environment to prevent water from

entering through the cord plug end, etc.

Fig. 1 – Typical Resident

Installation

This is a recommended

installation only.

1. General Information and Safety Guidelines

2. Installation

Produkt Specifikationer

Mærke:	Liberty Pumps
Kategori:	Pumpe
Model:	405HV

Har du brug for hjælp?

Hvis du har brug for hjælp til Liberty Pumps 405HV stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Pumpe Liberty Pumps Manualer

Liberty Pumps PRG101A Manual

27 Marts 2025

Liberty Pumps 405HV Manual

2 Oktober 2024

Pumpe Manualer

Nyeste Pumpe Manualer

16 Juni 2025

16 Juni 2025

10 Juni 2025

9 Juni 2025

9 Juni 2025

9 Juni 2025

9 Juni 2025

9 Juni 2025

9 Juni 2025

9 Juni 2025