Logik LDW45S10 Manual

Logik Opvaskemaskine LDW45S10

Læs gratis den danske manual til Logik LDW45S10 (2 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 46 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 23.5 anmeldelser. Har du et spørgsmål om Logik LDW45S10, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Thank you for purchasing a Logik dishwasher.

Please refer to this guide for the installation process.

1. Remove all packaging before positioning the machine. (Fig 1)

2. Please ensure the dishwasher is installed by a qualied technician. Refer to the tools required in Fig 2.

3. Ensure there is clearance each side of the unit to allow slight sideways movement for servicing when

required. Good levelling is essential for correct closure and sealing of the door. When the unit is correctly

levelled, the door should not catch the inner liner on either side of the cabinet. The adjustable feet may

be loosened or tightened in order to obtain the optimum leveling of the unit. (Fig 3)

4. If required, the worktop of the dishwasher can be removed. The height without the worktop is 820 mm.

Figure 3 outlines the minimum dimensions required to accommodate the dishwasher within tted

kitchen furniture units.

Do not connect the unit to the mains before installation. Ensure you are not installing the unit right in

front of the mains. This is to avoid potential damage to the back of the unit. (Fig 4)

5. The condensation strip must be tted to the underside of the worktop above your dishwasher to protect

it against any moisture. Its purpose is to protect your worktop’s underside from steam rising from the

dishwasher. (Fig 5 and 6)

• Ensure the surface is clean prior to sticking the condensation strip to the underside of the worktop.

• Remove the backing paper from the condensation strip. (Fig 5)

• Stick the condensation strip to the underside of the worktop. (Fig 6)

NOTE: FAILURE TO ATTACH THE CONDENSATION STRIP COULD RESULT IN DAMAGE TO THE UNDERSIDE OF

YOUR WORKTOP!

6. The worktop can be removed by removing the xing screws located at the rear of the dishwasher (Fig 7).

After removing the screws, lift and push the worktop forward to release the lugs from the front section of

the dishwasher. The polystyrene block and the lugs should be saved for future use.

7. Position the dishwasher next to a water tap and a drain. Ensure the water inlet and drain hoses are

not kinked or squashed. The unit must not stand on the mains cable. (Fig 8)

8. Make sure your plumbing is suitable for use with the dishwasher. If in doubt contact a qualied plumber.

This unit MUST BE connected to COLD WATER MAINS using the new water inlet hose. OLD HOSE SETS

MUST NOT BE RE-USED. The water pressure from the water mains needs to be at a minimum of 0.04 MPa

and a maximum of 1.00MPa.

Dishwasher Installation Guide

8. (continued)

• Connect one end of the safety water supply hose to your

dishwasher, and then connect the other end of the hose

to your water mains (Fig A). Please ensure the black

rubber seal is in place.

• After connecting the hose, turn on your water mains and

check for leaks.

• Connect the dishwasher to the mains socket.

NOTE: YOU MAY USE A Y-ADAPTOR (NOT INCLUDED)

FOR ADDITIONAL WATER FEED FOR ANOTHER APPLIANCE,

FOR INSTANCE A WASHING MACHINE. THIS IS ONLY

APPLICABLE FOR COLD WATER MAINS. A Y-ADAPTOR IS

AVAILABLE FROM MOST DIY STORES. (Fig A)

• Do not bend your drain hose. (Fig B)

• You may use the U-shaped drain hose holder to secure

your drain hose and to avoid bending it. (Fig C)

• Secure the water drain hose to the waste pipe to avoid it

coming o during the washing process. (Fig 9 and D)

NOTE: THE WASTE PIPE MUST ONLY BE CONNECTED TO

THE FOUL DRAINS AND NOT THE SURFACE WATER

DRAINAGE SYSTEM.

THE WATER DRAIN HOSE SHOULD BE PLACED BETWEEN 40

CM AND 100 CM FROM THE FLOOR LEVEL AND MUST NOT

BE EXTENDED, OTHERWISE THE UNIT MAY NOT BE ABLE TO

EXPEL THE WASTE WATER PROPERLY.

water mains

safety water supply hose

water drain hose

U-shaped drain hose

holder

Y-Adaptor

(not included)

Connect to

another

appliance

if required.

Logik LDW45S10_IG_GB_p1_100225.pdf 1 2/25/10 1:42 PM

Produkt Specifikationer

Mærke:	Logik
Kategori:	Opvaskemaskine
Model:	LDW45S10

Har du brug for hjælp?

Hvis du har brug for hjælp til Logik LDW45S10 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Opvaskemaskine Logik Manualer

Logik LDW45S10 Manual

26 August 2024

Logik LS474WN Manual

26 August 2024

Logik LDW45S12 Manual

26 August 2024

Logik LS474W Manual

25 September 2023

Logik LDW60S11 Manual

7 Juli 2023

Logik LID45W13N Manual

30 November 2022

Logik LF674SSN Manual

16 November 2022

Logik LDW60W16N Manual

7 November 2022

Logik LDW45S11 Manual

31 Oktober 2022

Logik LDW45W16N Manual

6 Oktober 2022

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Gorenje GU673A67W Manual

20 December 2025

Gorenje GS563B10X Manual

20 December 2025

BEKO BDFN26440WC Manual

20 December 2025

BEKO BDFN26550XC Manual

20 December 2025

BEKO BDUS26040XQ Manual

20 December 2025

BEKO BDIT16430 Manual

20 December 2025

BEKO BDSN25530X Manual

19 December 2025

BEKO BDIN25324 Manual

19 December 2025

Smeg STL5352C Manual

19 December 2025

BEKO BDSN38640X Manual

19 December 2025