Lorex LW4211B Manual

Lorex Overvågningskamera LW4211B

Læs gratis den danske manual til Lorex LW4211B (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 71 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 36 anmeldelser. Har du et spørgsmål om Lorex LW4211B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Resources

• Ensure your camera is placed as close to your receiver as possible.

• Reduce the number of obstructive materials between the camera and

the receiver. Concrete, brick, metal and wood are the most common

materials in your house that can cause poor signal strength.

To ensure the best possible wireless performance, it is

recommended to keep the following installation tips in mind

when choosing a location for the camera:

• Point the camera where there is the least amount of obstructions (i.e.,

tree branches).

• Install the camera where vandals cannot easily reach.

• This camera is rated for outdoor use. Installation in a sheltered location

is recommended.

• The camera uses the 2.4GHz band exclusively. Most new routers

support both 2.4GHz and 5GHz bands. It is recommended to use other

WiFi-connected devices using the 5GHz band when possible to ensure

the 2.4GHz band is not overcrowded.

• Other electronic devices such as microwaves, TVs, cordless phones,

and baby monitors can cause signal interference. It is recommended to

install the camera as far away from these devices as possible.

1080p MPX Wireless Security Camera

• 1080p MPX Wireless

Security Camera

• Wireless Receiver

• Antennas (×2)*

• Read this guide carefully and keep it for future reference.

• Follow all instructions for safe use of the product and handle with care.

• Use the camera within given temperature, humidity and voltage levels

noted in the camera’s speciﬁcations.

• Do not disassemble the camera.

• Do not point the camera directly towards the sun or a source of

intense light.

• Use only the supplied regulated power supply provided with the

product. Use of a non-regulated, non-conforming power supply can

damage the product and void the warranty.

• Periodic cleaning may be required. Use a damp cloth only. Do not use

any harsh, chemical-based cleaners.

* One each for camera and receiver.

Quick Start Guide

English Version 1.0

LW4211 SERIES

Package Contents

ATTENTION:

A REGULATED UL / CSA APPROVED power supply is REQUIRED for use

with this camera (included). Use of a non-regulated, non-conforming

power supply can damage this product and voids the warranty.

Safety Precautions

Installation Tips

Need Help?

Visit us online for

up-to-date software and

complete instruction

manuals

Click on the Downloads tab

Visit lorex.com

Search for the model number

of your product

Click on your product in the

search results

www.lorex.com

Dimensions

5.4” / 138mm

6.1” / 155mm

2.8” / 70mm

4.5” / 114mm

4.4” / 113mm

LW4211_QSG_EN_R1

As our products are subject to continuous improvement, Lorex reserves the right

to modify product design, speciﬁcations and prices, without notice and without

• For a full list of compatible recorders, visit lorex.com/compatibility

• Not intended for submersion in water.

• This camera includes an Auto Mechanical IR Cut Filter. When the

camera changes between Day/Night viewing modes, an audible clicking

noise may be heard from the camera. This clicking is normal, and

indicates that the camera ﬁlter is working.

Disclaimers

• Power Adapters (×2)*

• Mounting Kits (×2)*

• Allen Key

• BNC Adapter

LW4211_QSG_EN_R1

To install your camera:

Installing the Camera

Cable

Notch

IMPORTANT:

• Test your camera prior to selecting a permanent mounting location by

temporarily connecting the camera and cable to your DVR.

• Ensure the camera is no more than 700ft (213m) away from the wireless

receiver in an open ﬁeld (with line of sight between antennas). The range

is approximately 115ft (35m) or less in an indoor environment, depending

if there are walls or obstructions between the camera and receiver.

• Review the ‘Installation Tips’ section before choosing a mounting

location for the camera.

Before Installing the Camera

• Decide whether to run the cables through the

wall / ceiling (drilling required) or along the

wall / ceiling.

• If you run the cables along the wall / ceiling,

you must run the cable through the cable

notch on the base. This will keep the camera

base ﬂush to the surface when mounted.

1. Use the included mounting template or camera base to mark

holes for the included mounting screws. Drill holes where

marked.

NOTE: Ensure one of the included antennas is properly

attached to the camera.

2. Mount the camera to the mounting surface using the

included mounting screws (×3).

NOTE: Use the included drywall anchors (×3) if installing

into drywall.

3. Adjust the angle of the camera until the desired view is set.

Tighten the screws to secure the camera position.

Mounting Surface

Camera Base

Drywall Anchors (×3)

Mounting Screws (×3)

4. Connect the camera power adapter to the camera cable.

Connect the power adapter to a power outlet.

5. Remove protective ﬁlm from the camera lens.

Installing Multiple Wireless Cameras

When installing multiple digital wireless security cameras in the same

environment, maintain at least 4” / 10cm between the receivers to

optimize camera performance.

NOTE: It is not recommended to install more than 3 digital wireless

security cameras in the same environment to maintain optimal video

frame rate performance.

A. Use the included Allen key to

loosen the adjustment screw

on the camera base. Rotate the

arm of the camera up to 360°,

then tighten the screw.

B. Use the included Allen key to

loosen the adjustment screw.

Bend the arm of the camera up

to 90°, then tighten the screw.

C. Use the included Allen key to C

Setting Up the Receiver

1. Ensure one of the included antennas is properly attached to the

receiver.

2. Connect the receiver’s BNC cable to a compatible DVR’s video

input*.

3. Connect the receiver power adapter to the receiver. Connect the

power adapter to a power outlet.

NOTE: Make sure to ﬁrst connect and power on the camera before

powering on the receiver.

4. (Optional) Use the included double-sided tape to securely attach

the receiver to a ﬂat surface.

(OR)

Secure the receiver to a ﬂat surface using the included mounting

screws.

Connecting the receiver directly to DVR:

Connecting the receiver to DVR using a BNC extension cable:

Connect the BNC connector

to a video input on your DVR.

Connect the female power head

to the included receiver power

adapter.

Receiver DVR

Male Power Female Power

* This camera is only compatible with select DVRs. For a full list of

compatible recorders, visit lorex.com/compatibility.

** Not included. Compatible BNC extension cable available at lorex.com.

Connect the BNC

connector on the extension

cable to the included

BNC adapter. Connect

the adapter to the BNC

connector on the receiver.

Connect the male power

head to the female

power head on the

receiver.

Audio Settings

ATTENTION:

Audio recording without consent is illegal in certain jurisdictions. Lorex Corporation

assumes no liability for use of its products that does not conform with local laws.

Audio is disabled by default. You can enable audio through a

compatible Lorex DVR. For a full list of compatible recorders, visit

lorex.com/compatibility

NOTE: These instructions are based on current DVR interface. For

the most up-to-date instructions, see your DVR’s instruction manual

on .lorex.com

BNC Adapter

Pairing the Camera

The camera and receiver have already been paired out of the box. If for some

reason the pairing is lost, follow these steps to pair the camera and receiver.

Pair Button on

the Camera

To pair the camera and receiver:

Pair Button on

the Receiver

1. Make sure that the camera and receiver are

both powered up and all antennas properly

attached.

2. Press the pair button on the receiver (see

Figure 1).

3. Press and hold the pair button on the back

of the camera within 30 seconds of pressing

the pair button on the receiver (see Figure

2). If successful, live video from the camera

will appear on the monitor.

Figure 1

Figure 2

To enable camera audio on LHV / DV Series DVRs:

1. In Live View, right-click and click . Enter the system user Main Menu

name and password.

2. Click ( ) and select Recording Recording> .

loosen the adjustment screw furthest from the camera base. Rotate

the camera until it is level with the viewing area, then tighten the

screw.

3. Under , select Channel

the channel where the

audio-capable camera

is connected.

4. Under , Audio/Video

check the box on the

left to enable audio

recording.

5. Under , Audio Format

select the format

that will be used to

record audio. is G711a

recommended.

6. Click to save changes.OK

7. (Optional) Under , check the middle box to enable audio Audio/Video

when viewing cameras through the computer or mobile applications.

Produkt Specifikationer

Mærke:	Lorex
Kategori:	Overvågningskamera
Model:	LW4211B

Har du brug for hjælp?

Hvis du har brug for hjælp til Lorex LW4211B stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Lorex Manualer

Lorex W261AS Manual

19 Juli 2025

Lorex F861AS-AA Manual

4 Juli 2025

Lorex W281AA Manual

3 Juli 2025

Lorex LND45DVW Manual

3 Juli 2025

Lorex E863SD Manual

2 Juli 2025

Lorex E863SB Manual

2 Juli 2025

Lorex LNB95MBW Manual

2 Juli 2025

Lorex LNW16XF Manual

26 Juni 2025

Lorex LNE95MDB Manual

20 Juni 2025

Lorex LNZ45P25 Manual

20 Juni 2025

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

FLIR ioi HD CB-5222 Manual

30 Juli 2025

Eufy Cam S3 Pro Manual

30 Juli 2025

Telycam Vision+ 4KN 30X Manual

30 Juli 2025

Marshall Electronics CV630-BI Manual

30 Juli 2025

Telycam Vision+ SE Manual

30 Juli 2025

FLIR Ariel CC-3405 Manual

29 Juli 2025

FLIR Ariel CM-3505 Manual

29 Juli 2025

Axis Q6355-LE Manual

29 Juli 2025

Sony SNC-EMX52R Manual

29 Juli 2025

Hikvision DS-2CD3086G2H-LIU Manual

29 Juli 2025