Lorus W120 Manual

Lorus Ur W120

Læs gratis den danske manual til Lorus W120 (3 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Lorus W120, eller vil du spørge andre brugere om produktet?

Side 1/3
Button B : Calendar (month, date and day)
display in the time/calendar display.
• Start/stop in the stopwatch func-
tion.
Selection of the digits to be ad-
justed in the alarm setting func-
tion and the time/calendar set-
ting function.
Button C : Alarm display in the time/cal-
endar display.
Split/split release/reset in the
stopwatch function.
Setting the digits in the alarm
setting function and the time/
calendar setting function.
Stopping the alarm in any dis-
play.
Button
B while keeping button C pressed:
Engagement and disengagement
of the alarm and the time signal.
Button C while keeping button B pressed:
Changeover of the calendar (month
and date) display.
Buttons B & C:
Alarm test in the time/calendar
display.
CHARACTERISTICS
1. Time/calendar display: Hour, minute,
seconds, date, day of the week and month.
2. Automatic calendar adjustment: Cal-
endar adjusts automatically for odd and
even months except February of leap years.
3. Time indication: Changeover between
12-hour and 24-hour indications is pos-
sible.
4. Stopwatch: 24 hour stopwatch with 1/
100 second readout up to 1 hour and with
1 second readout after the first 1 hour.
Split time measurement is available.
5. Alarm: The alarm rings at the designated
hour and minutes for 20 seconds.
6. Hourly time signal: Can be set to ring
every hour on the hour with a single “beep”.
7. Illuminating light: The light illuminates
the display in the dark.
HOW TO SET THE DUAL CALEN-
DAR DISPLAY
1 Press button “B” to show the calendar (month,
date, and day) display. The calendar dis-
play is shown while button “B” is kept
pressed.
2 The month and the date change places
with each other with each press of button
“C” while keeping button “B” pressed.
INSTRUCTION MANUAL
CAL. W120 (RBZ SERIES)
CAL. W121 (RB6 SERIES)
CAL. W130 (RBN SERIES)
NREW120C 11-99
DISPLAY AND BUTTON OPERATION
Button A : Selection of the display.
The selection is made in the following order:
A
A
A
----------------------------
------
------
----------------------------
Time/calendar display
Stopwatch display
A
Time/calendar setting Alarm setting
Press
button “A”
for 2 seconds.
• The design of the digital display differs
depending on the calibre. The illustra-
tions of the display shown in this manual
refer to Cal. W120.
B
C
A
Light
button
Day indicator
Time signal mark Alarm mark
Seconds
MinutesHour
*In the 12-hour indication, the AM/PM mark
is displayed. In the 24-hour indication, there
is no indication.
DateMonth
Day Day
B
C
B
C
Date Month
HOW TO USE THE STOPWATCH
C: Split/
Split release/
Reset
A
1/100 seconds
B: Start/Stop
Stopwatch
indicator
Split indicator
Stop indicator 1/100 second
indicator
SecondsMinutes
1 Press button “A” to show the stopwatch
display. (The stopwatch indicator starts
flashing.)
The stopwatch can measure up to 24 hours
and is displayed in minutes, seconds, and
1/100 seconds up to 1 hour, and in hours,
minutes, and seconds after the first 1 hour.
(The 1/100 second indicator flashes dur-
ing the first 1 hour.)
When the measurement is over 24 hours,
the stopwatch will be reset to “0:00oo”
and start counting again.
2 Reset the digits to “0:00oo” before using
the stopwatch. When the split and the
stopwatch indicators are flashing, press
button “B” to check that the stop indicator
starts flashing, and then press button “C”
twice to reset the digits to zero.
3 When measuring a long period of time,
return the stopwatch to the time/calendar
display after the stopwatch starts to pre-
vent any possible mistaken operation.
* When button “B” or “C” is pressed in the
stopwatch display, a single “beep” sounds
to confirm the operation.
Accumulated elapsed time measurement
Start Stop Restart ResetStop
BB B BC
Restart and stop can be repeated by
pressing button “B”.
Measurement between two competitors
Split time measurement
Start
BC BC
Split
Split release
Stop Reset
C
Finish (First runner)
BCBCC
Finish (Second runner)
Start
Finish time
of 2nd
competitor
ResetStop
Measurement and release of split time
can be repeated by pressing button “C”.
Finish
time of 1st
competitor
HOW TO SET THE ALARM
Alarm and time signal
are disengaged.
Time signal is engaged.
Alarm is disengaged.
Alarm and time signal
are engaged.
The alarm rings at the designated time for 20
seconds and stops. However, the alarm can
be stopped manually by pressing button “C”
in any display.
ALARM TEST
Alarm is engaged.
Time signal is disengaged.
The alarm can be tested with a beeping sound
by pressing buttons “B” and “C” at the same
time in the time/calendar display.
HOW TO STOP THE ALARM
HOW TO SET THE TIME/CALENDAR
1 Press button “A” to activate the time/calendar
setting function. (The time/calendar setting
indicator and the second digits start flashing.)
2 Selection of the digits to be adjusted (flash-
ing) is made in the following order by
pressing button “B”.
3 One digit (flashing) is advanced with each
press of button “C”. (The digits except
seconds are advanced quickly by keeping
button “C” pressed.)
Seconds setting
Press button “C” in accordance with a
time signal. The seconds are reset to
“00” and start immediately.
When the seconds count any number
from “30” to “59” and button “C” is pressed,
one minute is added and the seconds
are immediately reset to “00”.
4 After all the adjustments are completed,
press button “A” to return to the time/
calendar display.
Note: When setting the hour digits, be sure
to check that the AM/PM mark is cor-
rectly set.
Seconds Minutes MonthHour
Day Date
→→
←←
HOW TO CHANGEOVER THE 12-HOUR
AND THE 24-HOUR INDICATIONS
In the calendar or the alarm display, each
press of button “A” changes over the time
indication display from the 12-hour to the 24-
hour and vice versa.
Changeover in the calendar display
24-hour
12-hour
A
A
Time/calendar setting
indicator
A
B
C
[Keeping button “B” pressed]
2 With each press of button “B” while keep-
ing button “C” pressed, the engagement
and disengagement of the alarm and the
time signal are made as follows:
HOW TO ENGAGE AND DISENGAGE
THE ALARM AND THE TIME SIG-
NAL
Alarm display
1 Press button “C” in the time/calendar dis-
play to show the alarm display. The alarm
display is shown while button “C” is kept
pressed.
B
C
“A” (AM)
Hour Minutes
Note: When setting the hour digits, be sure
to check that the “A” (AM)/“P” (PM)
mark is correctly set.
3 One digit (flashing) is advanced with each
press of button “C”. The digits are ad-
vanced quickly by keeping button “C” pressed.
4 After all the adjustments are completed,
press button “A” to return to the time/
calendar display.
(The display returns directly to the time/
calendar display and not to the time/cal-
endar setting.)
1 Press button “A” for 2 seconds to activate
the alarm setting function. (The alarm set
indicator starts flashing.)
2 Press button “B” to activate the “Hour” or
“Minute” setting. The display changes in
the following order with each press of button
“B”.
B
Hour setting
Minute setting
B
C
“A” (AM)
MinutesHour
Alarm set
indicator


Produkt Specifikationer

Mærke: Lorus
Kategori: Ur
Model: W120

Har du brug for hjælp?

Hvis du har brug for hjælp til Lorus W120 stil et spørgsmål nedenfor, og andre brugere vil svare dig