Lowrance LDT3200 Manual

Lowrance Navigator LDT3200

Læs gratis den danske manual til Lowrance LDT3200 (12 sider) i kategorien Navigator. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Lowrance LDT3200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

Pub. 988-0099-071

LDT-3200

Digital Temperature Gauge

Installation & Operation Instructions

The LDT-3200 combines a temperature gauge, voltmeter and clock in one

housing. It displays the temperature in either Fahrenheit °F or Celsius

°C and may be set to rotate between four gauge displays or "pages." The

unit fits in a standard 2-1/8" (54 mm) hole used by most marine equip-

ment manufacturers.

The gauge and its temperature sensor are designed to show surface water

temperature in a transom installation, but the sensor can be installed to

monitor the temperature elsewhere, such as in a live well.

LDT-3200 temperature gauge.

Mounting Preparations

When installed, the gauge will cover an area on the dash 2-3/8" (60.3 mm)

in diameter. To mount the unit, first make sure there is at least 2-3/4"

(70 mm) from the front of the dash to any obstruction behind the dash.

The maximum usable dash thickness is 1-1/8" (28.5 mm). Also, be sure

there is room to route the power and sensor cables. The following figure

shows gauge dimensions.

Dash installation, cross-section view.

Caution:

You should read over the entire installation section before drilling

any holes in your vessel!

You can install this gauge in some other order if you prefer, but we rec-

ommend this installation sequence, which is summarized below:

1. Determine the location for the gauge so you can plan how and where to

route the cables. This will help you make sure you have enough cable

length for the desired configuration.

2. Determine the location of your battery or other power connections,

along with the power cable route.

3. Determine the location for the temperature sensor and its cable route.

4. Determine the location for the alarm buzzer and its wire route.

5. If you want to turn on the gauge backlights whenever you turn on your

dashboard lights, locate your boat's dash light switch and determine how

to route the dash light wires to it.

6. Install the temp sensor, connect power wires to the battery and route

the power/sensor cable to the gauge location.

7. Install the gauge, and connect the power/sensor cable.

8. Connect the buzzer wires and install the buzzer. If desired, connect the

dash light wires to the boat's dash light switch.

2-3/4"

(70 mm)

2-3/8"

(60.3 mm)

Gasket

Threaded mounting collar

Dash

Cables

Produkt Specifikationer

Mærke:	Lowrance
Kategori:	Navigator
Model:	LDT3200

Har du brug for hjælp?

Hvis du har brug for hjælp til Lowrance LDT3200 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Navigator Lowrance Manualer

Lowrance HDS Carbon Manual

4 August 2025

Lowrance HDS Live Manual

4 August 2025

Lowrance Hook 2 7X GPS HDI Manual

7 Juli 2025

Lowrance Hook 2 4X Sonar Manual

6 Juli 2025

Lowrance Hook 2 7X GPS TS Manual

5 Juli 2025

Lowrance Hook 2 5X GPS HDI Manual

5 Juli 2025

Lowrance Elite FS Manual

9 August 2024

Lowrance Elite Ti Manual

9 August 2024

Lowrance iWAY 350C Manual

3 August 2024

Lowrance IFinder H2Oc Manual

2 August 2024

Navigator Manualer

Nyeste Navigator Manualer

Rand McNally OverDryve Manual

22 September 2025

Rand McNally TND 750 Manual

21 September 2025

Rand McNally RoadExplorer 70 Manual

21 September 2025

Rand McNally TND 740 Manual

20 September 2025

Rand McNally OverDryve 7 Manual

20 September 2025

Rand McNally RoadExplorer 80 Manual

20 September 2025

Rand McNally Foris Manual

20 September 2025

Rand McNally RoadExplorer 5 Manual

20 September 2025

Rand McNally IntelliRoute TND 700 Manual

20 September 2025

Rand McNally RVND 5525 LM Manual

20 September 2025