Lowrance LST3800 Manual

Lowrance Navigator LST3800

Læs gratis den danske manual til Lowrance LST3800 (12 sider) i kategorien Navigator. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Lowrance LST3800, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/12
1
Pub. 988-0064-351
LST-3800
In-Dash Digital Sonar Gauge
Installation & Operation Instructions
The LST-3800 is a depth and temperature gauge that comes with a 200
kHz transducer, features deep and shallow alarms and has three main
page displays. It can show depth in Meters or Feet, temperature in Fahr-
enheit or Celsius and its display may be set to rotate between Tempera-
ture, Depth or Dual display pages. The unit fits in a standard 2-1/8" (54
mm) hole used by most marine equipment manufacturers.
The 3800 is designed to display water depth and surface water tempera-
ture, but you MUST have a transducer with built-in temp sensor to re-
ceive temperature information.
LST-3800 temperature gauge.
Mounting Preparations
When installed, the gauge's bezel will cover a circular area at least 2-1/2"
(64 mm) wide on the front of the dash. To mount the unit, make sure
there is at least 4-1/8" (105 mm) from the front of the dash to any ob-
struction behind the dash. The maximum usable dash thickness is 1-1/8"
(28.5 mm). Also, make certain there is room to route the unit's cables.
The following figure shows gauge dimensions.
2
Dash installation, cross-section view.
Caution:
You should read over the entire installation section before drilling
any holes in your vessel!
You can install this gauge in some other order if you prefer, but we rec-
ommend the installation sequence summarized below:
1. Determine the location for the gauge so you can plan how and where to
route the cables. This will help you make sure you have enough cable
length for the desired configuration.
2. Determine the location of your battery or other power connections,
along with the power cable route.
3. Determine the location for the alarm buzzer and its wire route.
4. If you want to turn on the gauge backlights whenever you turn on your
dashboard lights, locate your boat's dash light switch and determine how
to route the dash light wires to it.
6. Install transducer, connect power wires to the battery and route the
power/transducer cable to the gauge location.
7. Install the gauge, and connect the power/transducer cable.
8. Connect the buzzer wires and install the buzzer. If desired, connect the
dash light wires to the boat's dash light switch.
4-1/8"
(105 mm)
2-1/2"
(64 mm)
Ga
s
ket
Threaded mounting collar
Dash
Cables

Produkt Specifikationer

Mærke: Lowrance
Kategori: Navigator
Model: LST3800

Har du brug for hjælp?

Hvis du har brug for hjælp til Lowrance LST3800 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Navigator Lowrance Manualer

Lowrance

Lowrance Elite FS Manual

9 August 2024
Lowrance

Lowrance Elite Ti Manual

9 August 2024
Lowrance

Lowrance iWAY 350C Manual

3 August 2024
Lowrance

Lowrance IFinder H2Oc Manual

2 August 2024
Lowrance

Lowrance LCX-25C Manual

1 August 2024
Lowrance

Lowrance iWAY 250C Manual

31 Juli 2024
Lowrance

Lowrance GlobalMap 8200C Manual

29 Juli 2024
Lowrance

Lowrance GlobalMap 6600C HD Manual

28 Juli 2024
Lowrance

Lowrance Elite-3x Manual

28 Juli 2024
Lowrance

Lowrance GlobalMap 4900M Manual

28 Juli 2024

Navigator Manualer

Nyeste Navigator Manualer

Curtis

Curtis GPD359B Manual

18 Juni 2025
ModeCom

ModeCom FreeWAY CX 7.0 Manual

9 Juni 2025
Holux

Holux GPSmile 6762D Manual

8 Juni 2025
Peiying

Peiying PY-GPS6005 Manual

7 Juni 2025
Peiying

Peiying PY-GPS5005 Manual

6 Juni 2025
Peiying

Peiying PY-GPS5003 Manual

6 Juni 2025
Holux

Holux GPSmile 52 Manual

3 Juni 2025
Holux

Holux GPSmile 61 Manual

3 Juni 2025
Holux

Holux GPSmile 51B Manual

2 Juni 2025
Holux

Holux GPSmile 62 Manual

2 Juni 2025