LYYT DK3-RGB30 Manual

LYYT Ikke kategoriseret DK3-RGB30

Læs gratis den danske manual til LYYT DK3-RGB30 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 7 anmeldelser. Har du et spørgsmål om LYYT DK3-RGB30, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
DIY LED TAPE KIT
User Manual
DIY LED TAPE KIT - SINGLE COLOUR
Introduction:
Thank you for purchasing the Lyyt DIY LED Tape . Kit LED tape is ideal for use on the underside of a counter tops, shelves, cupboards, around
window frames or in an alcove of a ceiling to name just a few examples.
Before starting please ensure that you have read this instruction leaflet carefully.
If you are unsure about any of the installation details, please have this installed by a competent installer.
Blister Contents:
1 x Reel of LED tape
1 x UK power adap tor
Possible Required tools: Scissors, Craft knife, Soldering iron and solder, 2 core DC wire and heat shrink tube.
Step 1: Preparation
Ensure that the surface you are attaching to is clear of dust and dirt. Clean thoroughly and leave to dry before fitting the tape.
Unravel the tape and connect the power supply. Check that all the LEDs are functioning correctly and if there are any faults return to your retailer
without delay.
Step 2: Cutti ng
WARNING: Disconnect from the power supply before attempting any cutting.
Measure out each section and cut with sharp scissors at the marked 5cm intervals to achieve the perfect length. Do not discard any excess tape as
it can be easily reconnected and used again (see FIG 2).
Step 3: Fitting:
Example 1: Simple straight run.
Clear the area you wish to install the tape and remove the backing paper, exposing the adhesive tape. Push tape firmly onto the surface. It is
recommended to work on 50cm sections at a time in order to ensure a professional finish. When you reach the end of your installation cut at the
marked cutting point.
Example 2: Requires cutting:
The tape can be cut at highlighted 5cm intervals for a perfect fit.
FIG 1:
DIY LED Tape User Manual Kit
You may also reconnect the two pieces by soldering the connection together (FIG 2). The tape has two tracks for the DC voltage with points +
positive pole at the top and negative pole at the bottom. –
To reattach, use a craft knife to cut the Epoxy coating from the terminals.
Use a soldering iron and solder to connect the DC wire to the relative terminals be sure not to cause a short circuit when making these connections,
as this will result in malfunction and possible damage to the power supply.
FIG 2:
WARNING: Only cut the tape on the highlighted intervals. Cutting the tape in other parts without due care will permanently damage that section
of the tape and will result in malfunction.
Points to remember when using this tape
1) Only use the supplied power adaptor for the length of tape in the kit
2) Only cut the tape at the highlighted 5cm intervals.
3) Do not connect another reel and operate from a single power supply as this will seriously affect the performance.
3) The top track of the tape is the + Positive pole.
4) The bottom track of the tape is the negative pole. –
5) Ensure you connect the correct wires otherwise the tape will not work.
6) Ensure that when soldering there are no short circuits
7) We recommend use heat shrink tubing to protect the connection. of
8) Check that everything operates correctly before installing.
FAQ:
Q) Can I connect different colours in a chain?
A) Yes all the LEDs draw the same power, current and have the same connection but do not exceed the full reel length.
Q) Can you cut a reel of tape into many different sections then connect them all together?
A) Yes as long as you cut the tape at 5cm intervals highlighted.
Q) I have connected two reels together off one power supply and the LEDs are dim towards the end.
A) The power adaptor is only designed to operate the reel in the kit. Anything longer will seriously affect the performance.
Q) Can I connect the tape together to form a loop?
A) Yes you can. This will even the brightness out on the LEDS across the reel length
Q) Can I use the tape outdoors?
A) Yes, the tape is IP65 rated. Ensure that the terminated ends are heat shrink protected.
Q) Can I clean the tape?
A) Yes, the tape is IP65 rated and has an epoxy coating. Just wipe down with a damp cloth regularly to ensure continuing brightness
Q) Can I replace / patch damaged tape with a new piece
A) Yes, just highlight the effected area by the 5cm intervals. Cut out the faulty section then fit in a new piece soldering the connections securely
and using heat shrink to protect the repaired connection.
Specifications
Voltage
12Vdc
Current consumption
340mA/m
Power consumption
4.08W/m
Number of LEDs
60/m
LED Spacing
16mm
Cut intervals
5cm
Beam angle
140° - 160°
LED type
SMD3528 or SMD2835
IP rating
IP65

Produkt Specifikationer

Mærke: LYYT
Kategori: Ikke kategoriseret
Model: DK3-RGB30

Har du brug for hjælp?

Hvis du har brug for hjælp til LYYT DK3-RGB30 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret LYYT Manualer

LYYT

LYYT CLIP10-B Manual

29 August 2024
LYYT

LYYT DIY-CW60 Manual

20 August 2024
LYYT

LYYT PS30-24 Manual

17 August 2024
LYYT

LYYT LT24560-BL Manual

16 August 2024
LYYT

LYYT DIY-B60 Manual

15 August 2024
LYYT

LYYT DIYH-RGB30 Manual

14 August 2024
LYYT

LYYT LT12560-WW Manual

14 August 2024
LYYT

LYYT PS40 Manual

14 August 2024
LYYT

LYYT RGB10-F Manual

14 August 2024
LYYT

LYYT LT12560-CW Manual

14 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman

Navman MY500XT Manual

1 August 2025
Navman

Navman FOCUS150 GPS Manual

1 August 2025
Scheppach

Scheppach TW1000 Manual

1 August 2025
Navman

Navman MiVue 750 WIFI Manual

1 August 2025
Navman

Navman MiVue Drive FHD Manual

1 August 2025
Midea

Midea MEC64 Manual

1 August 2025
Navman

Navman MY50T Manual

1 August 2025
Navman

Navman M100 Manual

1 August 2025
Navman

Navman MiVue 770 SAFETY Manual

1 August 2025
Navman

Navman MiVue 790 Manual

1 August 2025