LYYT LT12560-AM Manual

LYYT Ikke kategoriseret LT12560-AM

Læs gratis den danske manual til LYYT LT12560-AM (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 55 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 28 anmeldelser. Har du et spørgsmål om LYYT LT12560-AM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

SINGLE COLOUR LED TAPE

Installation Guide

Stock code

Voltage

Colour

Luminous flux

(Lumens per metre)

Light intensity per LED

(millicandelas)

156.704UK

12Vdc

540lm/m

5000mcd

156.705UK

12Vdc

Red

60lm/m

600mcd

156.706UK

12Vdc

Pink

120lm/m

1000m cd

156.708UK

12Vdc

Green

130lm/m

1200mcd

156.711UK

12Vdc

Blue

30lm/m

500mcd

156.714UK

12Vdc

Yellow

45lm/m

600mcd

156.715 UK

12Vdc

Cool white (6500K)

720lm/m

3996mcd

156.716 UK

12Vdc

Warm white (2700K)

720lm/m

3996mcd

156.755UK

24Vdc

Red

60lm/m

600mcd

156.756UK

24Vdc

Pink

120lm/m

1000mcd

156.758UK

24Vdc

Green

130lm/m

1200mcd

156.761UK

24Vdc

Blue

30lm/m

500mcd

156.764UK

24Vdc

Yellow

45lm/m

600mcd

156.765 UK

24Vdc

Cool white (6500K)

720lm/m

3996mcd

156.766 UK

24Vdc

Warm white (2700K)

720lm/m

3996mcd

Common Specifications

Number of LEDs

60/m

Beam angle

140°

Cut intervals

5cm

Reel length

LED type

Epistar™ SMD5050 for UV, SMD2835 for cool/warm white, SMD3528 for others

LED spacing

16mm

IP rating

IP65

Power consumption / metre

4.8W - (8.4W/m for UV 156.704UK)

Cross-section

10.5 x 2.55mm

Weight

210g - (230g for UV 156.704UK)

Single Col r LED Tape Installation Guide ou

Caution: Please read this guide carefully before installing Lyyt LED tape

Damage caused by incorrect application is not covered by the rranty wa

Lyyt single colour LED tape is supplied on 5m reels in either 12Vdc or 24Vdc voltages.

Installation should be carried out by competent electrical installers, observing the relevant electrical safety procedures.

Lyyt single colour LED tape has a self-adhesive backing to allow it to be easily attached to a clean, non-porous surface.

Where less than 5m of tape is needed, there are solder points as shown below, where the tape may be cut to size. These

cut points will be at 5cm intervals for 12V tape and 10cm intervals for 24V tape. In order to re-connect to another length

of tape after cutting, strip a y the epoxy coating at the solder points and solder a wire from “+” to “+” and a wire from wa

“-” to “-” as shown below. Some accessories are supplied with the tape reel for this purpose. In order to retain weather-

proofing, it is advised to seal the cuts and joints with silicone glue.

Ea 5m reel of single colour LED tape is fi ed with a 2.1 DC jack socket for po r input for easy connection to a ch tt mm we

power supply. This connector may be removed and stripped for bare wire co ection if a 2.1 jack is not fitted to the nn mm

power supply.

If the power supply has enough capacity to po r more than one reel, another r l can be co ected to the end of the we ee nn

first reel via the 2.1 DC jack plug mm . (Except for the 12V UV tape)

For 12V single colour LED tape, it is recommended to link no more than 15m of tape in sequence. For 24V versions, up to

30m can be linked in this way. Using a separate wire to loop “+” and “-” back to the power supply will help to avoid

dimming at the far end through voltage drop. To connect beyond these lengths, a parallel wire must be run from the

powe supply to the further reels of tape r . The UV tape will require seperate power supply to each 5m reel.

It is imperative that the power supply should have higher than the rated capacity in Amps (A) for the current required to

power the length(s) of LED tape installed. Please s the table below for reference. ee

10m

15m

20m

25m

30m

Current for 12V tape

10A

12A

Current for 24V tape

Please visit to select from our range of 12Vdc and 24Vdc power supplies that are suitable for powering www.avsl.com

Lyyt LED tapes.

Disp al:os The “Crossed Wheelie Bin” symbol on e product means at e product is classed as E ctrical or th th th le

E ctronic equip nt and sh ld not be disposed with other h sehold or co ercial waste at e end its useful fe. le me ou ou mm th of li

The g ds must be disposed of according to r cal co cil guidelines. oo you lo un

Errors and omissions excepted.

Tape Length

Current for UV tape 3.5A

Produkt Specifikationer

Mærke:	LYYT
Kategori:	Ikke kategoriseret
Model:	LT12560-AM

Har du brug for hjælp?

Hvis du har brug for hjælp til LYYT LT12560-AM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret LYYT Manualer

LYYT CLIP10-B Manual

29 August 2024

LYYT DIY-CW60 Manual

20 August 2024

LYYT PS30-24 Manual

17 August 2024

LYYT LT24560-BL Manual

16 August 2024

LYYT DIY-B60 Manual

15 August 2024

LYYT DIYH-RGB30 Manual

14 August 2024

LYYT LT12560-WW Manual

14 August 2024

LYYT PS40 Manual

14 August 2024

LYYT RGB10-F Manual

14 August 2024

LYYT LT12560-CW Manual

14 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Liteline LEDBAR34 Manual

19 Juni 2025

Festo EMMB-AS-40-01-S30M Manual

19 Juni 2025

Mr Safe JS7500 Manual

19 Juni 2025

Rane SEQ 30L Manual

19 Juni 2025

XP Gold Maxx Power Manual

19 Juni 2025

Fiamma Vent 50 Manual

19 Juni 2025

Rane SEQ 30S Manual

19 Juni 2025

Parkside PRM 1800 B2 Manual

19 Juni 2025

Xiaomi Air Fryer Essential 6L Manual

19 Juni 2025

Parkside HG09673 Manual

19 Juni 2025