Mach Power NW-PE100M Manual

Mach Power Ikke kategoriseret NW-PE100M

Læs gratis den danske manual til Mach Power NW-PE100M (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Mach Power NW-PE100M, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

USER MANUAL NW-PE100M

Trouble shooting

When the device encountered with troubles, it can be solved by the methods below:

1. Make sure the device is installed correctly referring to the requirements;

2. Make sure RJ45 cable is good contacted without open circuit; the cable design complies with

EIA/TIA568A or 568B international standards.

3. Each PoE port can provides max 15W to PoE devices, so please don’t connect with the PoE device which

is more than 15W.

4. Replace the trouble device with a normal working NW-PE100M to check if the device is damaged.

5. If all the above methods still don’t work, please contact with manufacturer directly.

PoE Extend

Long Distance PoE and

Extension Sol

Technical Specification

Port

Power Supply Mode

Transmission Media

Output Wattage

Bandwidth

Standard

Status Indicator

Dimensions (mm)

Weight

Operating Environment

One RJ45 port for PoE input, one RJ45 port for PoE output

Powered via PoE input port, support Mid-Span and End-Span

Cat5e/6 standard UTP cable

15.4w(max)

10/100Mbps

IEEE802.3 10BASE-T, IEEE802.3u 100BASE-TX/100BASE-FX, IEEE802.3az,

IEEE802.3af

PoE Indicator, Link/ActIndicator

83.0L x 51.5W x 24.0H

88.6g

Working Temperature: -10°C ~ 55°C

Storage Temperature: -40°C ~ 85°C

Humidity (non-congeal): 5% ~ 95%

Features

Provide two ports : one PoE input and one PoE output

Bandwidth: 10/100Mbps

Input Voltage: 48-57V

Complies with IEEE802.3 10BASE-T, IEEE802.3u, 100BASE-TX/100BASE-FX,

IEEE802.3az, IEEE802.3af

Easy to install and operate on walls or on the desktops.

Support overheating and short circuit protection as well as over-voltage

and over-load protection.

Overview

PoE extender can extend power and ethernet signals to 100m over UTP cable to connect PD devices

compatible with IEEE802.3 af/at (such as IP camera) and supply power to PD devices compatible with

IEEE802.3af/at. This PoE extender is widely used in video surveillance and office net cabling system. Max 3

pieces could be cascaded and transmit max up to 400 meter with PoE switch.

Typical applications diagram is as below:

Note: If any changes with product specification, forgive without prior notice

1. As transmission distance has certain relation with the cable, so you are suggested to use standard

cat5e/6 cable for longest distance needed.

Installation

Before installation, please check the following equipment and accessories, if there are any missing, please

contact with your supplier.

- n°1 NW-PE100M

- n°1 User manual

1. Before installation, please turn off the power of all signal sources and the monitor in case of the damage

to transmission device.

2. Using ONE network cableto connect with PoE input port and switch, as well as powered devices such as

IP camera via the other port.

3. Check whether installation is correct and the device undamaged. Before power on NW-PE100M, make

sure that all connections are reliable.

4. Confirm all network devices are powered and can work normally.

Making methods of RJ45 connector

Required tools: wire crimpers, network cable tester.

The wire sequence of RJ45l connector must complies with international standard of EIA/TIA 568A or

EIA/TIA 568B.

1. Strip about 2cm’s of insulating jacket to let 4 pairs UTP can be seen.

2. Separate 4 pairs UTP cable, and try to straighten each pair.

3. Arrange 8 cables with correct line sequence of EIA/TIA 568A or EIA/TIA 568B.

4. Cut thread residue and leave 1.5cm wire which exposed outside the insulating layer, and ensure 8 wires

are straight and neat.

5. Put 8 wires in RJ 45 connector, then press with wire crimpers.

6. Repeat above five steps , make the other side of UTP cable; Then using the cable tester to test whether

the cat5e/6 works normally.

PoE Camera

PoE Extender

PoE Switch

NVR

T568A

T568B

white

greeen

white

orange

greeen

orange

white

orange

white

green

blue

white

blue

white

blue

orange

green

white

brown

white

brown

Note:

Ports of this device support Auto MDI/MDIX, so the different

wire sequence at two sides of the cable is

allowed when using RJ45 port for transmission.

Produkt Specifikationer

Mærke:	Mach Power
Kategori:	Ikke kategoriseret
Model:	NW-PE100M

Har du brug for hjælp?

Hvis du har brug for hjælp til Mach Power NW-PE100M stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Mach Power Manualer

Mach Power NW-PSSO-004 Manual

29 August 2024

Mach Power SW-UG24L2F-075 Manual

29 August 2024

Mach Power EB-AT10232OS Manual

29 August 2024

Mach Power HC-EDC2035 Manual

29 August 2024

Mach Power VS-NVRP4C4K-313 Manual

29 August 2024

Mach Power IT-ULA65T8 Manual

29 August 2024

Mach Power IT-ULA90T8 Manual

29 August 2024

Mach Power HC-EDCP235 Manual

29 August 2024

Mach Power NW-PE100M Manual

28 August 2024

Mach Power EB-AT10232O Manual

28 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tripp Lite TLM406NC Manual

31 Juli 2025

Tripp Lite Protect It! TLP76RBTEL Manual

31 Juli 2025

Tripp Lite N286-40G-ESR4-J Manual

31 Juli 2025

Emos H5011 Manual

31 Juli 2025

Emos ZM6145 Manual

31 Juli 2025

Oppo Find X7 Manual

31 Juli 2025

Intellinet 713191 Manual

31 Juli 2025

Emos DCFW01 Manual

31 Juli 2025

AIC RSC-3ET Manual

31 Juli 2025

Tone City King Of Blues Overdrive Manual

31 Juli 2025